Kereskedelmi, irodai és ipari

Product Name:  2pcs 3.3-6V 3.7V 5V to 3V DC-DC Step-Down Power Supply Buck LDO Module
    
Module No.:  DD0403MA_3V*2
         
Packing list:
​2 PCS DD0403MA_3V 3.2V-6V to 3V DC DC Step Down Converter LDO Module
       
 
 
 
    
Description:
     
Low power consumption,Low ESR Cap.Compatible DD0403MA Series LDO Module,Very suitable for lithium battery-powered
   
Input voltage: DC 3.2-6V
  
Output voltage: DC 3V
  
Long time maximum output current 300mA
Short time maximum output current 400mA
 
Highly Accurate：±2%
 
Quiescent Current : 8uA
 
Short Circuit Current : 30mA
 
Over Current Protection : 500mA
 
Operating Temperature: -25℃ ~ 85℃
 
Size(Not including pin) : 11.6 x 7.8 x 2.5mm
 
Weight : 0.5g
 
  
     
Attention :
  
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
  
Applications:
   
 
3V MCU ARM CPU FPGA/CPLD
5V 3.7V TO 3V lithium battery-powered systems
3V Motor​ Toy
WIFI esp8266 Module
CCTV camera
Wireless Module:Nrf24l01 CC1101 CC2500 CC2530 Zigbee
Smart home / home automation
Distributed Power Systems
Battery Charger
Pre-Regulator for Linear Regulators
FM radio
Battery powered equipment
Audio amplifier
 
 
 
 
 
 
  

Product Name:  2pcs 3.3-6V 3.7V 5V to 3V DC-DC Step-Down Power Supply Buck LDO Module
    
Module No.:  DD0403MA_3V*2
         
Packing list:
​2 PCS DD0403MA_3V 3.2V-6V to 3V DC DC Step Down Converter LDO Module
       
 
 
 
    
Description:
     
Low power consumption,Low ESR Cap.Compatible DD0403MA Series LDO Module,Very suitable for lithium battery-powered
   
Input voltage: DC 3.2-6V
  
Output voltage: DC 3V
  
Long time maximum output current 300mA
Short time maximum output current 400mA
 
Highly Accurate：±2%
 
Quiescent Current : 8uA
 
Short Circuit Current : 30mA
 
Over Current Protection : 500mA
 
Operating Temperature: -25℃ ~ 85℃
 
Size(Not including pin) : 11.6 x 7.8 x 2.5mm
 
Weight : 0.5g
 
  
     
Attention :
  
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
  
Applications:
   
 
3V MCU ARM CPU FPGA/CPLD
5V 3.7V TO 3V lithium battery-powered systems
3V Motor​ Toy
WIFI esp8266 Module
CCTV camera
Wireless Module:Nrf24l01 CC1101 CC2500 CC2530 Zigbee
Smart home / home automation
Distributed Power Systems
Battery Charger
Pre-Regulator for Linear Regulators
FM radio
Battery powered equipment
Audio amplifier
 
 
 
 
 
 
  

Product Name : DC 3.3V 3.7V 5V LED Driver 30-1500MA Constant Current Adjustable Module PWM Control Board for USB LED flashlight 18650 Li-ion
   
Packing list:
 
1 PCS 30-1500MA LED Driver Constant current adjustable Module( no Pin)
 
Description: 
  
Working voltage : DC 2.8-6V(Perfect for 3V 3.3V 3.7V 4.5V 5V 6V LED Driver)
   
Output Current: 30-1500MA
   
Maximum output power: 9W
 
Can drive 1-16pcs 2.8-6V LEDs  (maximum current does not exceed 1.5A)
   
Current regulation: 1 through adjustable resistance; 2 through PWM signal control
 
Chip Temperature Regulation
Over LED Current Protection
Operating Temperature Range
 
Size : 18mm x 10.3mm x 2.8mm
Weight :  0.56g
 
 
 
 
 
 
Application 1: Wiring in accordance with the following figure, use a suitable screwdriver gently and slowly rotate the adjustable resistance.
 
Application 2: Adjust the adjustable resistance to 0 ohms (or maximize the current according to Application 1) and then use the MCU output PWM signal to control the LED output current
the frequency of the PWM signal should be less than 2KHz
 
 
 
 
 
 
LD06AJSA/B is a current regulation integrated circuit operating from an input voltage of 2.8V to 6V, the constant
output current can be set up to 1.5A with an external resistor. The LD06AJSA/B consists of high precision reference
voltage, amplifier, current mirror, etc. The on-chip power transistor and current sense block greatly reduce the
external component count, which makes the LD06AJSA/B ideal for LED driver.
When the CE pin is high, the input voltage is greater than 2.8V, and is larger than the LED forward voltage plus
the required voltage drop, LD06AJSA/B functions normally to deliver constant current from the LED pin.
The LD06AJSA/B adopts the temperature regulation instead of temperature protection function, the temperature
regulation can make the LED being turned on continuously in case of high ambient temperature or high voltage
drop. When the LD06AJSA/B junction temperature reaches about 135 ° C, the internal temperature regulation block
reduces the LED current so that the junction temperature will not rise any more. This feature allows the users to
maximize the use of the power handling capability of the chip, do not worry about the chip overheating and
damage to the chip or external components.
The LD06AJSA/B also has the chip enable function, which can shutdown the whole chip to limit the current
consumption within 1uA.
The LD06AJSA/B also adopts the over current protection block. When LED current approaches 1.9A(Typical), the
over current protection block begins to function to prevent the LED current from increasing further.
 
 

Product Name : DC 3.3V 3.7V 5V LED Driver 30-1500MA Constant Current Adjustable Module PWM Control Board for USB LED flashlight 18650 Li-ion
   
Packing list:
 
1 PCS 30-1500MA LED Driver Constant current adjustable Module( no Pin)
 
Description: 
  
Working voltage : DC 2.8-6V(Perfect for 3V 3.3V 3.7V 4.5V 5V 6V LED Driver)
   
Output Current: 30-1500MA
   
Maximum output power: 9W
 
Can drive 1-16pcs 2.8-6V LEDs  (maximum current does not exceed 1.5A)
   
Current regulation: 1 through adjustable resistance; 2 through PWM signal control
 
Chip Temperature Regulation
Over LED Current Protection
Operating Temperature Range
 
Size : 18mm x 10.3mm x 2.8mm
Weight :  0.56g
 
 
 
 
 
 
Application 1: Wiring in accordance with the following figure, use a suitable screwdriver gently and slowly rotate the adjustable resistance.
 
Application 2: Adjust the adjustable resistance to 0 ohms (or maximize the current according to Application 1) and then use the MCU output PWM signal to control the LED output current
the frequency of the PWM signal should be less than 2KHz
 
 
 
 
 
 
LD06AJSA/B is a current regulation integrated circuit operating from an input voltage of 2.8V to 6V, the constant
output current can be set up to 1.5A with an external resistor. The LD06AJSA/B consists of high precision reference
voltage, amplifier, current mirror, etc. The on-chip power transistor and current sense block greatly reduce the
external component count, which makes the LD06AJSA/B ideal for LED driver.
When the CE pin is high, the input voltage is greater than 2.8V, and is larger than the LED forward voltage plus
the required voltage drop, LD06AJSA/B functions normally to deliver constant current from the LED pin.
The LD06AJSA/B adopts the temperature regulation instead of temperature protection function, the temperature
regulation can make the LED being turned on continuously in case of high ambient temperature or high voltage
drop. When the LD06AJSA/B junction temperature reaches about 135 ° C, the internal temperature regulation block
reduces the LED current so that the junction temperature will not rise any more. This feature allows the users to
maximize the use of the power handling capability of the chip, do not worry about the chip overheating and
damage to the chip or external components.
The LD06AJSA/B also has the chip enable function, which can shutdown the whole chip to limit the current
consumption within 1uA.
The LD06AJSA/B also adopts the over current protection block. When LED current approaches 1.9A(Typical), the
over current protection block begins to function to prevent the LED current from increasing further.
 
 

Below item is powered by eletechsup Ltd . 
 
Product Name:   Multifunction with Enable ON/OFF 6W DC-DC Step-up Boost Converter Voltage Regulate 2.6-5V to 5V 6V 9V 12V 
  
Packing list:
 
1 PCS 6W DDEN12MB Input 2.6V-5.5V Output 5V/6V/9V12V DC-DC Boost Converter Module
（The output voltage is fixed and please select the voltage you need when purchasing.）
 
 
 
Description: 
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 94% Efficiency (usually is 75% -91% )
 
Quiescent current : Turn on output 210uA,Turn off output 5uA.
  
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
 
Size :  20 x 15 x 6MM
Weight : 1.5g
  
Protection : 
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP) 
 
Pin description:
 
Pin description:
Vi  : Input positive( )
En : Output enable, Connect to GND turn on output, Not connected(Or Connect to Vi)  turn off output
       This pin can also be controlled by MCU, low level turn on output, high level Turn off output
G  : Input and Output negative(GND/-)
Vo: Output positive( )
 
Output 5V :
  
Input voltage DC 2.6 ~ 4.5V,output DC 5V±3%
Maximum output : 5V/1300MA(See the table below for details)   
  
  
Output 6V :
  
Input voltage DC 2.6 ~ 5.5V,output DC 6V±3%
Maximum output : 6V/1100MA(See the table below for details)   
  
    
Output 9V :
  
Input voltage DC 2.6 ~ 5.5V,output DC 9V±3%
Maximum output : 12V/700MA(See the table below for details)   
  
   
Output 12V :
  
Input voltage DC 2.6 ~ 5.5V,output DC 12V±3%
Maximum output : 12V/550MA(See the table below for details)   
  
     
  
  
 Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router 
PLC RS485 devices
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
   
 
 
 
 

Below item is powered by Canton-Power Ltd . 
 
Product Name:   Auto Buck-Boost DC DC 0.9-6V to 3.3V Step-UP Step-Down Converter Board Power Supply Module DD0603SA_3V3
  
Packing list:
 
1 PCS DD0603SA_3V3 0.9-6V TO 3.3V DC DC Boost-Buck Converter Board
 
  
Description:
Input voltage DC 0.9 ~ 6V, output DC 3.3V( -5% )
 
The maximum input voltage can not exceed 6.5V
 
Auto Buck-Boost Converter Module working frequency 1MHZ.efficiency 61% -85% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Size : 22mm x 15mm x 5.7mm(Very small)
 
Weight : 2.6g(Very light)
  
   
 
   
Applications
Battery powered equipment
Breadboard Power Supply
ARM FPGA CPLD MCU Development board
electrical tools
Small power motors
Camera, Video camera
Toy car
power bank 
LED Lighting
Wireless communication equipment
Audio equipment
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 
 

Below item is powered by Canton-Power Ltd . 
 
Product Name:   Auto Buck-Boost DC DC 0.9-6V to 3.3V Step-UP Step-Down Converter Board Power Supply Module DD0603SA_3V3
  
Packing list:
 
1 PCS DD0603SA_3V3 0.9-6V TO 3.3V DC DC Boost-Buck Converter Board
 
  
Description:
Input voltage DC 0.9 ~ 6V, output DC 3.3V( -5% )
 
The maximum input voltage can not exceed 6.5V
 
Auto Buck-Boost Converter Module working frequency 1MHZ.efficiency 61% -85% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Size : 22mm x 15mm x 5.7mm(Very small)
 
Weight : 2.6g(Very light)
  
   
 
   
Applications
Battery powered equipment
Breadboard Power Supply
ARM FPGA CPLD MCU Development board
electrical tools
Small power motors
Camera, Video camera
Toy car
power bank 
LED Lighting
Wireless communication equipment
Audio equipment
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 
 

Below item is powered by Canton-Power Ltd . 
 
Product Name:   Auto Buck-Boost DC DC 0.9-6V to 3.3V Step-UP Step-Down Converter Board Power Supply Module DD0603SA_3V3
  
Packing list:
 
1 PCS DD0603SA_3V3 0.9-6V TO 3.3V DC DC Boost-Buck Converter Board
 
  
Description:
Input voltage DC 0.9 ~ 6V, output DC 3.3V( -5% )
 
The maximum input voltage can not exceed 6.5V
 
Auto Buck-Boost Converter Module working frequency 1MHZ.efficiency 61% -85% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Size : 22mm x 15mm x 5.7mm(Very small)
 
Weight : 2.6g(Very light)
  
   
 
   
Applications
Battery powered equipment
Breadboard Power Supply
ARM FPGA CPLD MCU Development board
electrical tools
Small power motors
Camera, Video camera
Toy car
power bank 
LED Lighting
Wireless communication equipment
Audio equipment
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 
 

Product Name : 3.7V 5V to 9V DC DC Converter Step-Up Boost Current Mode PWM Voltage Transformation Module
 
  Packing list:
1 PCS 5W 3V-6V TO 9V  Boost Step-UP Voltage Regulator    Module

 
 
Description: 
 
Input voltage 2.8~6V, output 9V (deviation -5% )
 
Maximum input current :  1.2A
Long-term work Current : 1A
Conversion efficiency : 81-91%
  
Start Voltage 2.8V, Output Current 60MA
 
INPUT 3V 1A;    OUTPUT    9V 290MA
INPUT 3.3V 1A;  OUTPUT  9V 330MA
INPUT 3.7V 1A;  OUTPUT  9V 360MA
INPUT 4.5V 1A;  OUTPUT  9V 440MA
INPUT 5V 1A;    OUTPUT   9V 490MA
INPUT 6V 1A;    OUTPUT   9V 590MA
 
DC-DC Boost module working frequency 1.0MHZ. 
Operating ambient temperature : -40~ 85 Degrees Celsius
2.54mm pin pitch,Arduiuo UNO DUE Breadboard FPGA/CPLD   Development Board friendly.
Excluding Pin Size 20.5mm x 10.16mm x 5.6mm(Very small)
Weight : about 1.4g(Very light)
 
Applications:
MCU Development Board,FPGA/CPLD UNO MEGA2560 DUE 8051 AVR C8051 etc
PLC Modbus RS485
Network equipment/Router
VCR
PDA
LED Lighting
9V Relay board
Wireless communication equipment
315M 433M Wireless remote controller
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter, a t this time of the input voltage is very low

Product Name : 3.7V 5V to 9V DC DC Converter Step-Up Boost Current Mode PWM Voltage Transformation Module
 
  Packing list:
1 PCS 5W 3V-6V TO 9V  Boost Step-UP Voltage Regulator    Module

 
 
Description: 
 
Input voltage 2.8~6V, output 9V (deviation -5% )
 
Maximum input current :  1.2A
Long-term work Current : 1A
Conversion efficiency : 81-91%
  
Start Voltage 2.8V, Output Current 60MA
 
INPUT 3V 1A;    OUTPUT    9V 290MA
INPUT 3.3V 1A;  OUTPUT  9V 330MA
INPUT 3.7V 1A;  OUTPUT  9V 360MA
INPUT 4.5V 1A;  OUTPUT  9V 440MA
INPUT 5V 1A;    OUTPUT   9V 490MA
INPUT 6V 1A;    OUTPUT   9V 590MA
 
DC-DC Boost module working frequency 1.0MHZ. 
Operating ambient temperature : -40~ 85 Degrees Celsius
2.54mm pin pitch,Arduiuo UNO DUE Breadboard FPGA/CPLD   Development Board friendly.
Excluding Pin Size 20.5mm x 10.16mm x 5.6mm(Very small)
Weight : about 1.4g(Very light)
 
Applications:
MCU Development Board,FPGA/CPLD UNO MEGA2560 DUE 8051 AVR C8051 etc
PLC Modbus RS485
Network equipment/Router
VCR
PDA
LED Lighting
9V Relay board
Wireless communication equipment
315M 433M Wireless remote controller
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter, a t this time of the input voltage is very low

Product Name: Xilinx USB Platform Cable  & SPARTAN-6 XC6SLX9 FPGA core Board spartan6 spartan 6 programmer Downloader kit CPLD xc6slx9-tqg144
 
 
Packing list:
 
1 PCS  XILINX XC6SLX9 FPGA Board
1 PCS  USB to mini USB Power Wire
 
1 x Xilinx Platform Cable USB Downloader
1 x 2.54MM pitch adapter plate(Three kinds of interfaces)
1 x 7PIN  2.54MM DuPont wire
1 x 6PIN  2.54MM DuPont wire
1 x 14PIN 2.0mm pitch cable
1 x 14PIN 2.54mm pitch cable
1 x 10PIN 2.54mm pitch cable 
1 x USB2.0 cable
 
 
XC6SLX9 FPGA Board  
 
 
Description:
 
1.Based on XILINX SPARTAN-6 XC6SLX9-TQG144 FPGA Chip;
 
2.Configuration Flash chip M25P40(Or compatible chip), 4M bit;
 
3.Onboard 25MHz active patch oscillator;
 
4.Onboard 8 IO control LEDs,1 power LED,1 Reset button,2 IO control button;
 
5.Leads the remaining IO, JTAG download port;
 
6.DC5V power supply;
 
7.Low-cost and efficient power supply design;
 
8.High-quality tantalum capacitor power supply filtering;
 
9.Development of embedded CPU support MicroBlaze;
 
10.2.54mm header pitch design, suitable for being plugged-in your application system;
 
11.Board size: 65*50MM;
 
 
Diagram : Please contact me on ebay message for diagram after your order !
 
front :
Back :
 
 
 
 
Xilinx Platform Cable USB Downloader  
 
Description:
 
Performance: 
Using CY7C68013A XC2C256 solution, fully compatible with the original XILINX Platform Cable USB 
Supports all Xilinx devices,FPGA/CPLD/3D IC/Soc/PROM 
Supports JTAG, Slave-Serial and SPI 
Interfaces to devices operating at 5V (TTL), 3.3V (LVCMOS), 2.5V, 1.8V and 1.5V 
Selectable target clock frequency, supports software automatic frequency adjustment 
 
Supported Software: 
Vivado Design Suite
Xilinx ISE Design Suite  
iMPACT 
ChipScope Pro

Product Name: Xilinx USB Platform Cable  & SPARTAN-6 XC6SLX9 FPGA core Board spartan6 spartan 6 programmer Downloader kit CPLD xc6slx9-tqg144
 
 
Packing list:
 
1 PCS  XILINX XC6SLX9 FPGA Board
1 PCS  USB to mini USB Power Wire
 
1 x Xilinx Platform Cable USB Downloader
1 x 2.54MM pitch adapter plate(Three kinds of interfaces)
1 x 7PIN  2.54MM DuPont wire
1 x 6PIN  2.54MM DuPont wire
1 x 14PIN 2.0mm pitch cable
1 x 14PIN 2.54mm pitch cable
1 x 10PIN 2.54mm pitch cable 
1 x USB2.0 cable
 
 
XC6SLX9 FPGA Board  
 
 
Description:
 
1.Based on XILINX SPARTAN-6 XC6SLX9-TQG144 FPGA Chip;
 
2.Configuration Flash chip M25P40(Or compatible chip), 4M bit;
 
3.Onboard 25MHz active patch oscillator;
 
4.Onboard 8 IO control LEDs,1 power LED,1 Reset button,2 IO control button;
 
5.Leads the remaining IO, JTAG download port;
 
6.DC5V power supply;
 
7.Low-cost and efficient power supply design;
 
8.High-quality tantalum capacitor power supply filtering;
 
9.Development of embedded CPU support MicroBlaze;
 
10.2.54mm header pitch design, suitable for being plugged-in your application system;
 
11.Board size: 65*50MM;
 
 
Diagram : Please contact me on ebay message for diagram after your order !
 
front :
Back :
 
 
 
 
Xilinx Platform Cable USB Downloader  
 
Description:
 
Performance: 
Using CY7C68013A XC2C256 solution, fully compatible with the original XILINX Platform Cable USB 
Supports all Xilinx devices,FPGA/CPLD/3D IC/Soc/PROM 
Supports JTAG, Slave-Serial and SPI 
Interfaces to devices operating at 5V (TTL), 3.3V (LVCMOS), 2.5V, 1.8V and 1.5V 
Selectable target clock frequency, supports software automatic frequency adjustment 
 
Supported Software: 
Vivado Design Suite
Xilinx ISE Design Suite  
iMPACT 
ChipScope Pro

Typical applications
1 Motor reversing control circuit,Power supply is DC 12V ,Wiring diagram below. "LOAD" may be DC 1-110V OR 85-265V AC/DC Motor
2 Live wire and Netural wire control circuit,Power supply is DC 12V ,Wiring diagram below. "LOAD" may be AC 85-265V equipment
 
Product Name: 5pcs KC22B02 DC 12V Power on Delay Relay Cycle Timer Switch Board 1-9999s for Motor Reversible Motorcycle
 
 
 
Package inlcuded:
5 PCS KC22B02 DC 12V 2 channel  delay relay module
 
 
 
Description: 
 
DC 12V 2 channels 0-9999 seconds multi-function delay relay board
9 kinds of functions can be switched
Products can set the delay time and Function.After setting up, power-up setting value is previous setting delay time and Function as we set last time  (power-down memory function);
 
Size: 75mm × 35mm x 20mm
Weight : 35.5g
Relay maximum load capacity: DC 1-110V/6A; AC 85-250V/5A
 
 
  
  
User Manua:
 
Noun resolved:
 
COM : Common terminal
 
NO: Normal open
 
NC: Normally Close
 
Relay close: COM connect NO,COM disconnect NC
 
Relay open : COM disconnect NO,COM connect NC
 
Function mode :
 
F1 After power on. Relay 1 close,relay 2 open, delay time is T1. Then relay 1 open,relay 2 is close. Delay time is T2.Relay 1 close, relay 2 open, delay time is T1.Such repeated cycles of action...(for Motor reversing)
 
F2 After power on.Relay 1 close, relay 2 close, delay time is T1. Then relay 1 open, relay 2 is open. Delay time is T2 . Relay 1 close , relay 2 close, delay time is T1. Such repeated cycles of action...
 
F3 After power on . Relay 1 close , delay time is T1. Then relay 1 open , Delay time is T2 . Relay 1 close,delay time is T1. Such repeated cycles of action... ,Relay 2 never work .
 
F4 After power on . Relay 2 open , delay time is T1. Then relay 2 close, Delay time is T2 . Relay 2 close , delay time is T1. Such repeated cycles of action... ,Relay 1 never work .
 
 
F5 After power on . Relay1 and relay 2 close, delay time is T1.Relay1 and relay 2 open (control Live wire and netural wire)
 
 
F6 After power on . Relay 1 close , delay time is T1. Then relay 1 open,Relay 2 never work .
 
F7 After power on . Relay 2 no action, delay time is T1. Then relay 2 close, Relay 1 never work .
 
F8 After power on. Relay 1 and Relay 2 both close, delay time is T1. Then relay 1 open,Delay time is T2, relay 2 open.
 
 
F9 After power on . Relay 1 and Relay 2 both open , delay time is T1. Then relay 1 close, Delay time is T2, relay 2 close.
   
Function Mode Switch:
 
Keep pressing K1, press K2 to switch Function mode
 
F5 F6 F7 mode has only 1 delay time counter (T1), the other mode has two delay time counters (T1 T2); Keep pressing K1 ,press K3, switch T1 T2 counter .
 
   
Adjustment delay time :
 
Press K2, switching 4 bits of delay time counter(0000~9999S),the selected bit flash , press K3 to adjusted counter . Repeat to switch the rest bits .
 
After switching all bits ,then press K2 exit adjustable delay mode; or press K1, exit adjustable delay mode; or wait 10 seconds exit adjustment mode
 
   
Display way :
 
Keep pressing the K3 for 5 seconds , the digital display Turn off. Keep pressing K3 5 second more (or re-power), the digital display Turn on .
 
F5 F6 F7 F8 F9 mode, the delay counter is completed, digital display Turn off, enter a low-power mode, press K1, exit the low-power mode
 

Typical applications
1 Motor reversing control circuit,Power supply is DC 12V ,Wiring diagram below. "LOAD" may be DC 1-110V OR 85-265V AC/DC Motor
2 Live wire and Netural wire control circuit,Power supply is DC 12V ,Wiring diagram below. "LOAD" may be AC 85-265V equipment
 
Product Name: 5pcs KC22B02 DC 12V Power on Delay Relay Cycle Timer Switch Board 1-9999s for Motor Reversible Motorcycle
 
 
 
Package inlcuded:
5 PCS KC22B02 DC 12V 2 channel  delay relay module
 
 
 
Description: 
 
DC 12V 2 channels 0-9999 seconds multi-function delay relay board
9 kinds of functions can be switched
Products can set the delay time and Function.After setting up, power-up setting value is previous setting delay time and Function as we set last time  (power-down memory function);
 
Size: 75mm × 35mm x 20mm
Weight : 35.5g
Relay maximum load capacity: DC 1-110V/6A; AC 85-250V/5A
 
 
  
  
User Manua:
 
Noun resolved:
 
COM : Common terminal
 
NO: Normal open
 
NC: Normally Close
 
Relay close: COM connect NO,COM disconnect NC
 
Relay open : COM disconnect NO,COM connect NC
 
Function mode :
 
F1 After power on. Relay 1 close,relay 2 open, delay time is T1. Then relay 1 open,relay 2 is close. Delay time is T2.Relay 1 close, relay 2 open, delay time is T1.Such repeated cycles of action...(for Motor reversing)
 
F2 After power on.Relay 1 close, relay 2 close, delay time is T1. Then relay 1 open, relay 2 is open. Delay time is T2 . Relay 1 close , relay 2 close, delay time is T1. Such repeated cycles of action...
 
F3 After power on . Relay 1 close , delay time is T1. Then relay 1 open , Delay time is T2 . Relay 1 close,delay time is T1. Such repeated cycles of action... ,Relay 2 never work .
 
F4 After power on . Relay 2 open , delay time is T1. Then relay 2 close, Delay time is T2 . Relay 2 close , delay time is T1. Such repeated cycles of action... ,Relay 1 never work .
 
 
F5 After power on . Relay1 and relay 2 close, delay time is T1.Relay1 and relay 2 open (control Live wire and netural wire)
 
 
F6 After power on . Relay 1 close , delay time is T1. Then relay 1 open,Relay 2 never work .
 
F7 After power on . Relay 2 no action, delay time is T1. Then relay 2 close, Relay 1 never work .
 
F8 After power on. Relay 1 and Relay 2 both close, delay time is T1. Then relay 1 open,Delay time is T2, relay 2 open.
 
 
F9 After power on . Relay 1 and Relay 2 both open , delay time is T1. Then relay 1 close, Delay time is T2, relay 2 close.
   
Function Mode Switch:
 
Keep pressing K1, press K2 to switch Function mode
 
F5 F6 F7 mode has only 1 delay time counter (T1), the other mode has two delay time counters (T1 T2); Keep pressing K1 ,press K3, switch T1 T2 counter .
 
   
Adjustment delay time :
 
Press K2, switching 4 bits of delay time counter(0000~9999S),the selected bit flash , press K3 to adjusted counter . Repeat to switch the rest bits .
 
After switching all bits ,then press K2 exit adjustable delay mode; or press K1, exit adjustable delay mode; or wait 10 seconds exit adjustment mode
 
   
Display way :
 
Keep pressing the K3 for 5 seconds , the digital display Turn off. Keep pressing K3 5 second more (or re-power), the digital display Turn on .
 
F5 F6 F7 F8 F9 mode, the delay counter is completed, digital display Turn off, enter a low-power mode, press K1, exit the low-power mode
 

Below item is powered by eletechsup Ltd .
 
Product Name: 10x Mini 5w 2.6-6v To 3.7v 5v 12v Boost Regulator Module Dc-Dc Boost Converter Module DD0512MA
  
Packing list:
 
10 PCS 6W DD0512MA Ultra-small Ultra-small & Ultra-thin DC-DC Step-up Converter
 
Description:  
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 94% Efficiency (usually is 84% -91% )
 
Quiescent current : 0.19MA.
 
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
 
Size : 13 x 11 x 5.2mm(Ultra small and thin)
Weight : 1g(Ultralight)
 
 
Protection :
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP)
 
Pin description:
 
Pin description:
Vi : Input positive( )
GND : Input and Output negative(GND/-)
Vo : Output positive( )
 
Output 3.7V :
 
Input voltage DC 2.6 ~ 3.6V,output DC 3.7V±3%
Maximum output : 3.7V/1200MA(See the table below for details)
 
Output 5V :
 
Input voltage DC 2.6 ~ 4.5V,output DC 5V±3%
Maximum output : 5V/1200MA(See the table below for details)
 
 
 
Output 12V :
 
Input voltage DC 2.6 ~ 6V,output DC 12V±3%
Maximum output : 12V/500MA(See the table below for details)
 
 
 
 Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router
PLC RS485 devices
Lithium battery power supply equipment
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
 
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
 
 
 
 
 

Below item is powered by eletechsup Ltd . 
 
Product Name:   10x 6W tiny 3V 3.3V 3.7V 4.2V 5V to 12V DC-DC Boost Step up Converter Module
   
Packing list:
  10 PCS 6W mini 2.6-6V to 3.7V 5V 12V Boost Voltage Regulator Module
 
 
 
 
 
Description:  
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 93% Efficiency (usually is 84% -91% )
 
Quiescent current : 0.21MA.
  
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
  
Size : 13 x 11 x 5.2mm(Ultra small & Ultra-thin) 
Weight :  1g(Ultralight)
  
  
Protection : 
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP) 
 
Pin description:
 
Pin description:
Vi       : Input positive( )
GND  : Input and Output negative(GND/-)
Vo      : Output positive( )
 
 
  
 
Output 12V :
  
Input voltage DC 2.6 ~ 6V,output DC 12V±3%
Maximum output : 12V/500MA(See the table below for details)   
  
     
  
  
  Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router 
PLC RS485 devices
Lithium battery power supply equipment
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 

   
 
 
 
 
 
 

Below item is powered by eletechsup Ltd . 
 
Product Name:   10x 6W tiny 3V 3.3V 3.7V 4.2V 5V to 12V DC-DC Boost Step up Converter Module
   
Packing list:
  10 PCS 6W mini 2.6-6V to 3.7V 5V 12V Boost Voltage Regulator Module
 
 
 
 
 
Description:  
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 93% Efficiency (usually is 84% -91% )
 
Quiescent current : 0.21MA.
  
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
  
Size : 13 x 11 x 5.2mm(Ultra small & Ultra-thin) 
Weight :  1g(Ultralight)
  
  
Protection : 
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP) 
 
Pin description:
 
Pin description:
Vi       : Input positive( )
GND  : Input and Output negative(GND/-)
Vo      : Output positive( )
 
 
  
 
Output 12V :
  
Input voltage DC 2.6 ~ 6V,output DC 12V±3%
Maximum output : 12V/500MA(See the table below for details)   
  
     
  
  
  Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router 
PLC RS485 devices
Lithium battery power supply equipment
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 

   
 
 
 
 
 
 

 
 
Product Name: 433M 4 Key HCS301 Rolling Code Keyfob & DC 12V 4CH RKE Secure Remote Keyless Entry System Remote Controller
 
 
 
Package inlcuded(It is recommended to choose to buy a transceiver kit):
1 PCS 433M DC 12V 4CH Rolling Code Relay Module
1 PCS 433M HCS301 Rolling Code Keyfob
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 14MA, 1 relay open 42MA, 2 relays open 69MA, 3 relays open 96MA, 4 relays open 122MA;
3. Wireless Receiving frequency : 433.92M ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. The maximum remote control distance is 30-50 meters
8. size (including shell) 75*54*28mm;
9. weight : 84 grams;
10. Relay Maximum Load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
RKE Secure Remote Keyless Entry system
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Encryption keys are read protected.
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Notice:
This Remote CANNNOT cannot copy or clone any other brand remote , it doesnot have copy function . it can only work with our own rolling code receiver.

Product Name: 12Key 433M 20dBm FSK Moisture proof Rolling Code Remote Control & 12ch -121dBm High Sensitivity Wireless Controller Relay Kit DC 12V 24V
 
 
Package inlcuded:
1PCS DC 12V/24V 12ch 433M Industrial grade Wireless Controller Kit
 
 
 
 
 
Description:
 
Product Specifications:
1. Working voltage: DC 12V (24V optional);
2. Working current (DC 12V): standby current 8MA, single relay working current is about 30MA
3. 8 working modes including ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence'';
4. Encoding and decoding type: Rolling Code (similar to HCS301), which can be adapted to up to 32 remote controllers;
5. Remote control type: RC44B12 industrial-grade remote control, using 2pcs AA 1.5V Batteries
(no batteries, you need to bring your own);
6. Remote control distance: 300-500 meters in open space (wireless receiving sensitivity: -121dBm; wireless transmitting power: 20dBm);
 
7. Output: Relay NO COM NC;
8. Size: Wireless Controller 125*79*30mm; Remote Control 165*70*46mm
 
9. Weight: Wireless Controller 238 grams ; Remote Control 309 grams
 
10. The maximum load capacity of the relay: DC 1-110V/5A; AC 85-265V/6A.
 
Product Features:
 
12-channel multi-function wireless controller, each channel is independently controlled and will not interfere with each other.
8 working modes: ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence''
 
For more information, please contact me
learning (adapting)
In learning mode, press different remote control buttons to adapt to different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
Clear code:
 
Press and hold the KEY button on the receiver for about 8 seconds until the indicator light goes out, indicating that it has been cleared successfully. The receiver can store 30 remote controls with different codes.
 
Learning (adapting):
 
1. Press the key button on the receiver, the LED light is on, and enter the learning state; according to the function you need, choose to press a key on the remote control to learn, and the indicator light flashes once after the receiver receives the signal, indicating that the learning is successful. If the learning fails, the indicator light will go out directly.
Working mode:
When learning, by pressing different remote control buttons, it can be set to 8 different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
1. Self-locking mode : Press the No. 1 button on the remote control to learn
2. Momentary mode : Press the No. 2 button of the remote control to learn
(when Momentary mode it can support multiple buttons to output at the same time, the relays are triggered independently, and do not affect each other)
3. Interlock mode : Press the No. 3 button on the remote control to learn
4. Relay 1~6 channels Self-locking and 7~12 channels Momentary coexist : Press the No. 4 button of the remote control to learn
 
5. Relay 1 channel Self-locking and 2~12 channels Momentary coexist : Press the No. 5 button of the remote control to learn
 
6. Relay 1 and 3 channel Self-locking, 2 4 5 6 7 8 9 10 11 12 channels Momentary coexist : Press the No. 7 button of the remote control to learn
 
7. Relay 1~10 channel Self-locking, No. 11 button Open 1~10 Relay,No. 12 button Close 1~10 Relay : Press the No. 8 button of the remote control to learn
 
8. Relay 1-2 channels Interlock , 3 4 5 6 7 8 9 10 channels Momentary,11-12 channels Self-locking : Press the No. 7 button of the remote control to learn
Wiring diagram:
DC 1-100V OR AC 85-265V control circuit,Wiring diagram below. ''LOAD'' may be LED lights, fans, motors and other DC AC equipment

Product Name: 12Key 433M 20dBm FSK Moisture proof Rolling Code Remote Control & 12ch -121dBm High Sensitivity Wireless Controller Relay Kit DC 12V 24V
 
 
Package inlcuded:
1PCS DC 12V/24V 12ch 433M Industrial grade Wireless Controller Kit
 
 
 
 
 
Description:
 
Product Specifications:
1. Working voltage: DC 12V (24V optional);
2. Working current (DC 12V): standby current 8MA, single relay working current is about 30MA
3. 8 working modes including ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence'';
4. Encoding and decoding type: Rolling Code (similar to HCS301), which can be adapted to up to 32 remote controllers;
5. Remote control type: RC44B12 industrial-grade remote control, using 2pcs AA 1.5V Batteries
(no batteries, you need to bring your own);
6. Remote control distance: 300-500 meters in open space (wireless receiving sensitivity: -121dBm; wireless transmitting power: 20dBm);
 
7. Output: Relay NO COM NC;
8. Size: Wireless Controller 125*79*30mm; Remote Control 165*70*46mm
 
9. Weight: Wireless Controller 238 grams ; Remote Control 309 grams
 
10. The maximum load capacity of the relay: DC 1-110V/5A; AC 85-265V/6A.
 
Product Features:
 
12-channel multi-function wireless controller, each channel is independently controlled and will not interfere with each other.
8 working modes: ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence''
 
For more information, please contact me
learning (adapting)
In learning mode, press different remote control buttons to adapt to different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
Clear code:
 
Press and hold the KEY button on the receiver for about 8 seconds until the indicator light goes out, indicating that it has been cleared successfully. The receiver can store 30 remote controls with different codes.
 
Learning (adapting):
 
1. Press the key button on the receiver, the LED light is on, and enter the learning state; according to the function you need, choose to press a key on the remote control to learn, and the indicator light flashes once after the receiver receives the signal, indicating that the learning is successful. If the learning fails, the indicator light will go out directly.
Working mode:
When learning, by pressing different remote control buttons, it can be set to 8 different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
1. Self-locking mode : Press the No. 1 button on the remote control to learn
2. Momentary mode : Press the No. 2 button of the remote control to learn
(when Momentary mode it can support multiple buttons to output at the same time, the relays are triggered independently, and do not affect each other)
3. Interlock mode : Press the No. 3 button on the remote control to learn
4. Relay 1~6 channels Self-locking and 7~12 channels Momentary coexist : Press the No. 4 button of the remote control to learn
 
5. Relay 1 channel Self-locking and 2~12 channels Momentary coexist : Press the No. 5 button of the remote control to learn
 
6. Relay 1 and 3 channel Self-locking, 2 4 5 6 7 8 9 10 11 12 channels Momentary coexist : Press the No. 7 button of the remote control to learn
 
7. Relay 1~10 channel Self-locking, No. 11 button Open 1~10 Relay,No. 12 button Close 1~10 Relay : Press the No. 8 button of the remote control to learn
 
8. Relay 1-2 channels Interlock , 3 4 5 6 7 8 9 10 channels Momentary,11-12 channels Self-locking : Press the No. 7 button of the remote control to learn
Wiring diagram:
DC 1-100V OR AC 85-265V control circuit,Wiring diagram below. ''LOAD'' may be LED lights, fans, motors and other DC AC equipment

Product Name: 12Key 433M 20dBm FSK Moisture proof Rolling Code Remote Control & 12ch -121dBm High Sensitivity Wireless Controller Relay Kit DC 12V 24V
 
 
Package inlcuded:
1PCS DC 12V/24V 12ch 433M Industrial grade Wireless Controller Kit
 
 
 
 
 
Description:
 
Product Specifications:
1. Working voltage: DC 12V (24V optional);
2. Working current (DC 12V): standby current 8MA, single relay working current is about 30MA
3. 8 working modes including ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence'';
4. Encoding and decoding type: Rolling Code (similar to HCS301), which can be adapted to up to 32 remote controllers;
5. Remote control type: RC44B12 industrial-grade remote control, using 2pcs AA 1.5V Batteries
(no batteries, you need to bring your own);
6. Remote control distance: 300-500 meters in open space (wireless receiving sensitivity: -121dBm; wireless transmitting power: 20dBm);
 
7. Output: Relay NO COM NC;
8. Size: Wireless Controller 125*79*30mm; Remote Control 165*70*46mm
 
9. Weight: Wireless Controller 238 grams ; Remote Control 309 grams
 
10. The maximum load capacity of the relay: DC 1-110V/5A; AC 85-265V/6A.
 
Product Features:
 
12-channel multi-function wireless controller, each channel is independently controlled and will not interfere with each other.
8 working modes: ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence''
 
For more information, please contact me
learning (adapting)
In learning mode, press different remote control buttons to adapt to different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
Clear code:
 
Press and hold the KEY button on the receiver for about 8 seconds until the indicator light goes out, indicating that it has been cleared successfully. The receiver can store 30 remote controls with different codes.
 
Learning (adapting):
 
1. Press the key button on the receiver, the LED light is on, and enter the learning state; according to the function you need, choose to press a key on the remote control to learn, and the indicator light flashes once after the receiver receives the signal, indicating that the learning is successful. If the learning fails, the indicator light will go out directly.
Working mode:
When learning, by pressing different remote control buttons, it can be set to 8 different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
1. Self-locking mode : Press the No. 1 button on the remote control to learn
2. Momentary mode : Press the No. 2 button of the remote control to learn
(when Momentary mode it can support multiple buttons to output at the same time, the relays are triggered independently, and do not affect each other)
3. Interlock mode : Press the No. 3 button on the remote control to learn
4. Relay 1~6 channels Self-locking and 7~12 channels Momentary coexist : Press the No. 4 button of the remote control to learn
 
5. Relay 1 channel Self-locking and 2~12 channels Momentary coexist : Press the No. 5 button of the remote control to learn
 
6. Relay 1 and 3 channel Self-locking, 2 4 5 6 7 8 9 10 11 12 channels Momentary coexist : Press the No. 7 button of the remote control to learn
 
7. Relay 1~10 channel Self-locking, No. 11 button Open 1~10 Relay,No. 12 button Close 1~10 Relay : Press the No. 8 button of the remote control to learn
 
8. Relay 1-2 channels Interlock , 3 4 5 6 7 8 9 10 channels Momentary,11-12 channels Self-locking : Press the No. 7 button of the remote control to learn
Wiring diagram:
DC 1-100V OR AC 85-265V control circuit,Wiring diagram below. ''LOAD'' may be LED lights, fans, motors and other DC AC equipment

Product Name: 12Key 433M 20dBm FSK Moisture proof Rolling Code Remote Control & 12ch -121dBm High Sensitivity Wireless Controller Relay Kit DC 12V 24V
 
 
Package inlcuded:
1PCS DC 12V/24V 12ch 433M Industrial grade Wireless Controller Kit
 
 
 
 
 
Description:
 
Product Specifications:
1. Working voltage: DC 12V (24V optional);
2. Working current (DC 12V): standby current 8MA, single relay working current is about 30MA
3. 8 working modes including ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence'';
4. Encoding and decoding type: Rolling Code (similar to HCS301), which can be adapted to up to 32 remote controllers;
5. Remote control type: RC44B12 industrial-grade remote control, using 2pcs AA 1.5V Batteries
(no batteries, you need to bring your own);
6. Remote control distance: 300-500 meters in open space (wireless receiving sensitivity: -121dBm; wireless transmitting power: 20dBm);
 
7. Output: Relay NO COM NC;
8. Size: Wireless Controller 125*79*30mm; Remote Control 165*70*46mm
 
9. Weight: Wireless Controller 238 grams ; Remote Control 309 grams
 
10. The maximum load capacity of the relay: DC 1-110V/5A; AC 85-265V/6A.
 
Product Features:
 
12-channel multi-function wireless controller, each channel is independently controlled and will not interfere with each other.
8 working modes: ''Momentary'', ''Self-locking'', ''Interlock'', ''Self-locking and Momentary coexistence''
 
For more information, please contact me
learning (adapting)
In learning mode, press different remote control buttons to adapt to different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
Clear code:
 
Press and hold the KEY button on the receiver for about 8 seconds until the indicator light goes out, indicating that it has been cleared successfully. The receiver can store 30 remote controls with different codes.
 
Learning (adapting):
 
1. Press the key button on the receiver, the LED light is on, and enter the learning state; according to the function you need, choose to press a key on the remote control to learn, and the indicator light flashes once after the receiver receives the signal, indicating that the learning is successful. If the learning fails, the indicator light will go out directly.
Working mode:
When learning, by pressing different remote control buttons, it can be set to 8 different working modes
Note: If you want to change the working mode, please clear the receiver and then re-learn.
1. Self-locking mode : Press the No. 1 button on the remote control to learn
2. Momentary mode : Press the No. 2 button of the remote control to learn
(when Momentary mode it can support multiple buttons to output at the same time, the relays are triggered independently, and do not affect each other)
3. Interlock mode : Press the No. 3 button on the remote control to learn
4. Relay 1~6 channels Self-locking and 7~12 channels Momentary coexist : Press the No. 4 button of the remote control to learn
 
5. Relay 1 channel Self-locking and 2~12 channels Momentary coexist : Press the No. 5 button of the remote control to learn
 
6. Relay 1 and 3 channel Self-locking, 2 4 5 6 7 8 9 10 11 12 channels Momentary coexist : Press the No. 7 button of the remote control to learn
 
7. Relay 1~10 channel Self-locking, No. 11 button Open 1~10 Relay,No. 12 button Close 1~10 Relay : Press the No. 8 button of the remote control to learn
 
8. Relay 1-2 channels Interlock , 3 4 5 6 7 8 9 10 channels Momentary,11-12 channels Self-locking : Press the No. 7 button of the remote control to learn
Wiring diagram:
DC 1-100V OR AC 85-265V control circuit,Wiring diagram below. ''LOAD'' may be LED lights, fans, motors and other DC AC equipment

 
 
Product Name:433M 20dB Serial Port RF Wireless Transmission Module Wireless pass-through UART RS232 Board replace GPRS GSM WIFI Bluetooth DTU
 
 
 
Recommendation: buy 2 pcs
 
 
 
 
Qty :
 
1 pcs 433M RS232 Data transparent transmission module#with Plastic shell#;
 
1 pcs 433M SMA Antenna
 
1 pcs DC5#5mm to DC3#5mm Power cable
 
 
 
 
 
Overview:
HY-RS232 series is a low cost, high performance transparent FSK transceiver with operating at 433/470/868/915 MHz. It features small size, high output power, high sensitivity,long transmission distance and high communication data rate with auto set up for communication change and data receiving and transmission control. There is UART interface, it is easy to realize the wireless data transmission with only providing the UART data. It is flexible for the users to set the UART baud rate, frequency,output power, data rate, frequency deviation, receiving bandwidth etc parameters. It is your ideal choice for designing wireless data transmission products which can be widely used on wireless data transmission field.
 
 
 
Features
 
Baud Rate : 1200-115200bps#Default: 9600#;
 
Work voltage: DC 5V #Range:4.5~8V#;
 
FSK modulation, 2-way half -duplex communication, strong anti-interfere;
Maximal output power100mW#20dBm#,output power adjustable between 1-20dBm;
Sensitivity -117dBm;
Supply current for Tx 100mA@20dBm, 40mA@14dBm;
Supply current for Rx 25mA;
Low current sleep mode 1uA;
Standard RS232 DB9 COM interface;
Operation frequency can be configured, acceptable for several modules working in different frequency with no disturbance on each other;
Optional for frequency deviation and receiving ISM bandwidth, users can be modulated by software;
Easily use, auto exchange on communication & transceiver;
Communication speed 1.2kbps -115.2kbps,can be modulated through software;
Afford ENABLE control signal,user self control work duty cycle;
RSSI function;
With LED indication;
Longer transmission distance,over 1Km in open air;
Small size 43.7*34X1.2MM,9 PIN DIP & 9 PIN SMD package,easy for assembly;
Tuning free;
Accord FCC,ETSI standard;
 
 
 
Application
Remote control, remote measurement system;
Wireless meter;
 
Smart Home,Home Automation ,Wiser Home;
Access control ;
Identification system;
Data collection;
IT household appliance;
Intelligence household appliance ;
Baby monitoring system;
 
 
 

 
 
Product Name:433M 20dB Serial Port RF Wireless Transmission Module Wireless pass-through UART RS232 Board replace GPRS GSM WIFI Bluetooth DTU
 
 
 
Recommendation: buy 2 pcs
 
 
 
 
Qty :
 
1 pcs 433M RS232 Data transparent transmission module#with Plastic shell#;
 
1 pcs 433M SMA Antenna
 
1 pcs DC5#5mm to DC3#5mm Power cable
 
 
 
 
 
Overview:
HY-RS232 series is a low cost, high performance transparent FSK transceiver with operating at 433/470/868/915 MHz. It features small size, high output power, high sensitivity,long transmission distance and high communication data rate with auto set up for communication change and data receiving and transmission control. There is UART interface, it is easy to realize the wireless data transmission with only providing the UART data. It is flexible for the users to set the UART baud rate, frequency,output power, data rate, frequency deviation, receiving bandwidth etc parameters. It is your ideal choice for designing wireless data transmission products which can be widely used on wireless data transmission field.
 
 
 
Features
 
Baud Rate : 1200-115200bps#Default: 9600#;
 
Work voltage: DC 5V #Range:4.5~8V#;
 
FSK modulation, 2-way half -duplex communication, strong anti-interfere;
Maximal output power100mW#20dBm#,output power adjustable between 1-20dBm;
Sensitivity -117dBm;
Supply current for Tx 100mA@20dBm, 40mA@14dBm;
Supply current for Rx 25mA;
Low current sleep mode 1uA;
Standard RS232 DB9 COM interface;
Operation frequency can be configured, acceptable for several modules working in different frequency with no disturbance on each other;
Optional for frequency deviation and receiving ISM bandwidth, users can be modulated by software;
Easily use, auto exchange on communication & transceiver;
Communication speed 1.2kbps -115.2kbps,can be modulated through software;
Afford ENABLE control signal,user self control work duty cycle;
RSSI function;
With LED indication;
Longer transmission distance,over 1Km in open air;
Small size 43.7*34X1.2MM,9 PIN DIP & 9 PIN SMD package,easy for assembly;
Tuning free;
Accord FCC,ETSI standard;
 
 
 
Application
Remote control, remote measurement system;
Wireless meter;
 
Smart Home,Home Automation ,Wiser Home;
Access control ;
Identification system;
Data collection;
IT household appliance;
Intelligence household appliance ;
Baby monitoring system;
 
 
 

 
 
Product Name: with ARDUINO sketch 16x16 Matrix Dot Red mini LED Display for UNO MEGA2560 DUE NANO LEONARDO MICRO Raspberry Pi
 
Packing list:
1 PCS mini size 16x16 1.9mm F2.0 Red Pixel Dot Matrix LED
 
Description:
 
Matrix display module 16x16 dot
Red pixels
Pixel size: 1.9MM
74hc595 driver
Can display variety of patterns and characters
Provided arduiuo UNO/MGEA2560 code
Size(Excluding Pin): 40MM x 40MM x 10mm(mini)
Weight : 18.5g
Applicable MCU platform :
UNO MEGA2560 DUE NANO LEONARDO MICRO
FPGA/CPLD
STM32 C51 AVR PIC
raspberry pi
Nodemcu
NOTE :
1 For ARDUIUO CPU frequency is relatively low, If more than 3 modules are connected in series, the LED will flash..
2 We only provide ARDUINO sketch, MCU (C51/ARM/AVR) please modify the code by yourself, ''modify IO port operation mode''
 
 
With the display you get full documentantion and example sketch by email!
 
 
Use:
 
USE for Arduiuo UNO R3:
 
 
You can use this software,make your favorite patterns:
 
 
 
Display effect:
 

 
 
Product Name: with ARDUINO sketch 16x16 Matrix Dot Red mini LED Display for UNO MEGA2560 DUE NANO LEONARDO MICRO Raspberry Pi
 
Packing list:
1 PCS mini size 16x16 1.9mm F2.0 Red Pixel Dot Matrix LED
 
Description:
 
Matrix display module 16x16 dot
Red pixels
Pixel size: 1.9MM
74hc595 driver
Can display variety of patterns and characters
Provided arduiuo UNO/MGEA2560 code
Size(Excluding Pin): 40MM x 40MM x 10mm(mini)
Weight : 18.5g
Applicable MCU platform :
UNO MEGA2560 DUE NANO LEONARDO MICRO
FPGA/CPLD
STM32 C51 AVR PIC
raspberry pi
Nodemcu
NOTE :
1 For ARDUIUO CPU frequency is relatively low, If more than 3 modules are connected in series, the LED will flash..
2 We only provide ARDUINO sketch, MCU (C51/ARM/AVR) please modify the code by yourself, ''modify IO port operation mode''
 
 
With the display you get full documentantion and example sketch by email!
 
 
Use:
 
USE for Arduiuo UNO R3:
 
 
You can use this software,make your favorite patterns:
 
 
 
Display effect:
 

 
Product Name: 12V 24V 12 NPN Digital IO RS485 Relay Module Modbus RTU DIN35 C45 Rail Box for PLC PTZ Configuration Software touch screen
 
 
 
Package inlcuded:
  1PCS DC 12V/24V 12 Input & 12 Output RS485 Relay Module
 
 
Description:
1: DC 12V (12V Version), DC 24V (24V Version)
 
2: Standby current (all relays closed) 14MA, 1 relay open 41MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 226MA
 
3 12 photoelectric isolation Input ports (NPN low level active ), the input and output relationship can be set to associated (default) and non-associated through commands.
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' ''''Interlock between two channels'' 7 Commands
 
5: MODBUS RTU command, Support 03 06 16 function code
 
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 The default baud rate is 9600BPS. The baud rate can be selected through jumpers: 2400 4800 9600 19200BPS
 
10 Size: 180 * 72 * 20mm(Only PCB Board);184 * 88* 42mm(with Din Rail Box)
11 Weight: 190g(Only PCB Board);318g(with Din Rail Box)
12 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
  
 
For more information, please contact me
 
DIN rail Box parameters:
Product model: UM72
Color: green
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 180 mm PCB boards
Net weight: 128g
Installation: DIN35 and C45 rail
 
 
Application
 
PLC IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
Configuration Software
 
Typical applications:
1 The dial switch (slave address) is invalid and can only control one module at a time.
 
MODBUS RTU command mode (HEX), you can control a variety of ways: Serial Hyper Terminal Control (need to manually add the CRC), Modbus Poll software control (software automatically add the CRC), PLC or MCU process control
 
 
 
Wiring Diagram:
 
1 DC 12V/24 control circuit,Wiring diagram below. ''LOAD'' may be camera,LED lights, fans, motors and other DC 12V/24V equipment
 
 
 
 
2 DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V/24V load, need another DC 12V/24V power supply). ''LOAD'' may be LED lights, fans, motors Lights, fluorescent lights, solar water heaters and other DC AC equipmen
Test Software(We offer a demo video):
Serial HyperTerminal:
 
Modbus Poll
 
 
 
 

Typical applications:
  
Motor Toy car Model aircraft 2A Driver
ARDUIUO UNO MEGA2560 Pro mini DUE
breadboard PCB Universal board
raspberry pi ARM AVR PIC
DC 5V 9V 12V Home lighting system 
Smart Home / Home Automation
LED lighting
12V DC Motor,RS360
 5V DC Motor
 
There are a variety of installation,can for breadboard ,PCB, Universal board,UNO MEGA2560 raspberry pi
 
 
Wiring Diagram 1:
 5.5-12V DC operating voltage DC 5.5-12V devices
 
 
Wiring Diagram 2:
5.5-12V DC operating voltage ,DC 1-48V OR AC 85-265V devices
 
  
Wiring Diagram 3:
3 5V DC operating voltage ,DC 5 V devices
Wiring Diagram 4:
4 5V DC operating voltage ,DC 1-48V OR AC 85-265V devices
 
 
 
 
 
Product Name : DC 5V 6V 9V 12V LED Motor Toy car Model aircraft 2A Driver EV1527 Remote control mini Wireless remote control switch Relay Kit
 
Packing list:
1 PCS MINI 433M DC 5V 9V 12V 4 Channel Wireless Controller 
4 PCS  433M 4 Button EV1527 Remote Control( USE 12V 27A battery,Batteries not included )
1 PCS Plastic shell
1 PCS 2.54MM straight pin
1 PCS 2.54MM curved pin

 
 
Features:
 
1 Operating voltage: Power 1: DC  5V,6V , 9V, 12V (range 5 -15V) ; Power 2: DC 4.2-5V
 
2 Operating current: Standby Current(12V 8MA, 5V 8MA); each relay operating current 40MA
 
3 Wireless frequency: 433M(315M version can be customized)
 
4 Receiver sensitivity: -108dBm
 
5 Decode: learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 6 remote control
 
6 work mode: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
 
7 Relay load voltage: DC 1-48V; AC 85-265V
 
8 Relay load current: <= 2A
 
9 Size: 49mmx25.5mmx14mm (Very small)
 
10 Weight: 16g(Very light)
  
Normally, we would adapter remote control and receiver.
If the item you received has not been adapted Or you need to add accessories, Please follow the instructions below
 
study method:
Clean code: Hold down the learn button down, LED stays on for 4-5 seconds and then turns off
Learning: Hold down the learn button, LED light after release; immediately press the remote control button, LED flashes three times, learning success
 
Use more details, please click here!
 
 
Work mode:
There are three Work modes, Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
two pads of T1  connected is Inter-locking (Latch) mode,two pads of T2  connected is Self-locking (Toggle),
All disconnect is Non-locking (Momentary is defult)
  
Mode Description:
Momentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A, the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;
Toggle     : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as BCD. Every Channel is Independent ;
Latch      : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2/3/4 is Close.Press transmitter button B, the receiver Channel 2 is Open, the Channel 1/3/4 is Close.
 
 
 
 
433M 4 Button EV1527 Remote Control:
 
Power supply : 12V 27A battery  replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current:  ≤ 12mA ;
Oscillation mode:  SAW resonator ;
Oscillation resistor : 330K
Modulation mode: ASK OOK ;
Operating frequency: 433.92MHz  ;
Frequency dev iation: ±0.2MHz ;
Encoding format: Million  Group Code (  EV1527 ) ;
Transmit power: 10 mW.
Data Rate : 50~60KHZ;
  
 
 
 

Typical applications:
  
Motor Toy car Model aircraft 2A Driver
ARDUIUO UNO MEGA2560 Pro mini DUE
breadboard PCB Universal board
raspberry pi ARM AVR PIC
DC 5V 9V 12V Home lighting system 
Smart Home / Home Automation
LED lighting
12V DC Motor,RS360
 5V DC Motor
 
There are a variety of installation,can for breadboard ,PCB, Universal board,UNO MEGA2560 raspberry pi
 
 
Wiring Diagram 1:
 5.5-12V DC operating voltage DC 5.5-12V devices
 
 
Wiring Diagram 2:
5.5-12V DC operating voltage ,DC 1-48V OR AC 85-265V devices
 
  
Wiring Diagram 3:
3 5V DC operating voltage ,DC 5 V devices
Wiring Diagram 4:
4 5V DC operating voltage ,DC 1-48V OR AC 85-265V devices
 
 
 
 
 
Product Name : DC 5V 6V 9V 12V LED Motor Toy car Model aircraft 2A Driver EV1527 Remote control mini Wireless remote control switch Relay Kit
 
Packing list:
1 PCS MINI 433M DC 5V 9V 12V 4 Channel Wireless Controller 
4 PCS  433M 4 Button EV1527 Remote Control( USE 12V 27A battery,Batteries not included )
1 PCS Plastic shell
1 PCS 2.54MM straight pin
1 PCS 2.54MM curved pin

 
 
Features:
 
1 Operating voltage: Power 1: DC  5V,6V , 9V, 12V (range 5 -15V) ; Power 2: DC 4.2-5V
 
2 Operating current: Standby Current(12V 8MA, 5V 8MA); each relay operating current 40MA
 
3 Wireless frequency: 433M(315M version can be customized)
 
4 Receiver sensitivity: -108dBm
 
5 Decode: learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 6 remote control
 
6 work mode: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
 
7 Relay load voltage: DC 1-48V; AC 85-265V
 
8 Relay load current: <= 2A
 
9 Size: 49mmx25.5mmx14mm (Very small)
 
10 Weight: 16g(Very light)
  
Normally, we would adapter remote control and receiver.
If the item you received has not been adapted Or you need to add accessories, Please follow the instructions below
 
study method:
Clean code: Hold down the learn button down, LED stays on for 4-5 seconds and then turns off
Learning: Hold down the learn button, LED light after release; immediately press the remote control button, LED flashes three times, learning success
 
Use more details, please click here!
 
 
Work mode:
There are three Work modes, Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
two pads of T1  connected is Inter-locking (Latch) mode,two pads of T2  connected is Self-locking (Toggle),
All disconnect is Non-locking (Momentary is defult)
  
Mode Description:
Momentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A, the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;
Toggle     : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as BCD. Every Channel is Independent ;
Latch      : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2/3/4 is Close.Press transmitter button B, the receiver Channel 2 is Open, the Channel 1/3/4 is Close.
 
 
 
 
433M 4 Button EV1527 Remote Control:
 
Power supply : 12V 27A battery  replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current:  ≤ 12mA ;
Oscillation mode:  SAW resonator ;
Oscillation resistor : 330K
Modulation mode: ASK OOK ;
Operating frequency: 433.92MHz  ;
Frequency dev iation: ±0.2MHz ;
Encoding format: Million  Group Code (  EV1527 ) ;
Transmit power: 10 mW.
Data Rate : 50~60KHZ;
  
 
 
 

Below item is powered by Canton-electronics Ltd .
 
​Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.
 
Modules No: RT390
 
1 pcs Super-Heterodyne decoder receiver and 1 pcs 12 buttons PT2262 encoder transmitter ;
 
 
 
Receiver :
 
Module No.: RF11A04
 
Description:
Model No.: RF11A04 OR CE-RF11A-045V
1. Features:
Operating voltage: DC 3-5V
Operating current: less 11mA (DC 5V)
Working priceple: super heterodyne
modulation Mode: OOK / ASK
Operating Frequency : 433.92MHZ
Receiving sensitivity: -108dBm
Output level: 5V TTL level, low standby, the maximum current 20MA (to add a current-limiting resistor)
Decode: learning code, adapted EV1527 / PT2262 and a compatible remote control, you can store up to eight remote control
Working modes: Non-locking (Momentary ), self-locking (Toggle), Inter-locking; 0.1-500000 seconds adjustable delay time
Size: 30x12.1x12.5mm
Weight: 4 grams or less
 
 
2. Pin Description
G: GND pin, DC 3-5V power supply negative
V: VCC pin, DC 3-5V positive power supply
D0: channel 1 output, active high
D1: channel 2 output, active high
D2: Channel 3 output, active high
D3: Channel 4 output, active high
VT: channel output valid signal, the microcontroller can be used as an interrupt signal
 
3. the working mode
 
You can select different modes of operation with"M4 M3 M2 M1 M0" pad in the delay mode to adjust the delay time through an adjustable resistor.
In delay mode, the rotary variable resistor can adjust the delay time. Increase the time counterclockwise rotation, and clockwise rotation to shorten the time. Adjustable resistor is a precision resistor, adjust the time with a Phillips screwdriver to gently rotate (do not use excessive force)
Working Mode Description:
Non-locking: Press the remote control button, the IO port outputs high. Release the remote control button, IO port outputs low.
Self-locking: Press the remote control button, the IO port outputs high. Press the remote control button again, IO port outputs low.
Interlock: Press the remote control button D0, D0 IO port outputs high, other IO ports outputs low; remote control button is pressed D1, D1 IO port outputs high, other IO ports output low and so on.
Delay: Under Delay mode, there is a delay 0/1/2/3/4 five sub-patterns, by adjusting the variable resistor IO port high duration
4, the adapter remote control (learning remote control)
In normal operation mode, LED (D1) will be lit, when receiving a valid remote control (EV1527 / PT2262) key value, LED will flash.
Clean code: hold the button to press.LED offs, keep pressing about 8 seconds until LED lights. At that time, clean code completion (Note: After the implementation of clean code, previous remote controls do not exist.
Adaptation (learning):
Step 1 (into the learning mode):trigger the key button, LED offs;
Step 2 (adapter channel 1): press the first button of remote control and then, LED offs after flashes for four times. This time means that it had learned the value of the first button
Step 3 (Adaptation Channel 2): Press the second remote control, LED offs after flashes 4 times, This time means that it had learned the value of the second button
Step 4 (adapter Channel 3): Then press the remote's third button, LED offs after flashes 4 times, This time means that it had learned the value of the third button
Step 5 (Adaptation Channel 4): Then press the remote control's fourth button, LED lights after flashes 4 times, This time means that it had learned the value of the fourth button.
NOTE: The process must be completed within 15 seconds
 
Adaptation Video,Click here!
 
5. Wiring Diagram :
Control LED indicator: see "RF11A04_LED demo"
Control 12V Relay: See "RF11A04_4Relay demo"
Click here for more help!
 
 
 
Connect with ardiuno :
 
 
 
 
Transmitter :
 
 
Features / Specifications :
1. 4 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
 
Technical Data :
Transmitter Module No.: TB420;
Power supply : 12V 23A battery (not included )  ,
 
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format: SCT2260  fixed code (compatiable for PT2262 SC2262 PT2260 PT2264 , can work with PT2272-M4 ,PT2272-T4,PT2272-L4 );
RC  Resistance : 4.7M; 
Transmit power : 200mW ;
 

Below item is powered by Canton-electronics Ltd .
 
​Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.
 
Modules No: RT390
 
1 pcs Super-Heterodyne decoder receiver and 1 pcs 12 buttons PT2262 encoder transmitter ;
 
 
 
Receiver :
 
Module No.: RF11A04
 
Description:
Model No.: RF11A04 OR CE-RF11A-045V
1. Features:
Operating voltage: DC 3-5V
Operating current: less 11mA (DC 5V)
Working priceple: super heterodyne
modulation Mode: OOK / ASK
Operating Frequency : 433.92MHZ
Receiving sensitivity: -108dBm
Output level: 5V TTL level, low standby, the maximum current 20MA (to add a current-limiting resistor)
Decode: learning code, adapted EV1527 / PT2262 and a compatible remote control, you can store up to eight remote control
Working modes: Non-locking (Momentary ), self-locking (Toggle), Inter-locking; 0.1-500000 seconds adjustable delay time
Size: 30x12.1x12.5mm
Weight: 4 grams or less
 
 
2. Pin Description
G: GND pin, DC 3-5V power supply negative
V: VCC pin, DC 3-5V positive power supply
D0: channel 1 output, active high
D1: channel 2 output, active high
D2: Channel 3 output, active high
D3: Channel 4 output, active high
VT: channel output valid signal, the microcontroller can be used as an interrupt signal
 
3. the working mode
 
You can select different modes of operation with"M4 M3 M2 M1 M0" pad in the delay mode to adjust the delay time through an adjustable resistor.
In delay mode, the rotary variable resistor can adjust the delay time. Increase the time counterclockwise rotation, and clockwise rotation to shorten the time. Adjustable resistor is a precision resistor, adjust the time with a Phillips screwdriver to gently rotate (do not use excessive force)
Working Mode Description:
Non-locking: Press the remote control button, the IO port outputs high. Release the remote control button, IO port outputs low.
Self-locking: Press the remote control button, the IO port outputs high. Press the remote control button again, IO port outputs low.
Interlock: Press the remote control button D0, D0 IO port outputs high, other IO ports outputs low; remote control button is pressed D1, D1 IO port outputs high, other IO ports output low and so on.
Delay: Under Delay mode, there is a delay 0/1/2/3/4 five sub-patterns, by adjusting the variable resistor IO port high duration
4, the adapter remote control (learning remote control)
In normal operation mode, LED (D1) will be lit, when receiving a valid remote control (EV1527 / PT2262) key value, LED will flash.
Clean code: hold the button to press.LED offs, keep pressing about 8 seconds until LED lights. At that time, clean code completion (Note: After the implementation of clean code, previous remote controls do not exist.
Adaptation (learning):
Step 1 (into the learning mode):trigger the key button, LED offs;
Step 2 (adapter channel 1): press the first button of remote control and then, LED offs after flashes for four times. This time means that it had learned the value of the first button
Step 3 (Adaptation Channel 2): Press the second remote control, LED offs after flashes 4 times, This time means that it had learned the value of the second button
Step 4 (adapter Channel 3): Then press the remote's third button, LED offs after flashes 4 times, This time means that it had learned the value of the third button
Step 5 (Adaptation Channel 4): Then press the remote control's fourth button, LED lights after flashes 4 times, This time means that it had learned the value of the fourth button.
NOTE: The process must be completed within 15 seconds
 
Adaptation Video,Click here!
 
5. Wiring Diagram :
Control LED indicator: see "RF11A04_LED demo"
Control 12V Relay: See "RF11A04_4Relay demo"
Click here for more help!
 
 
 
Connect with ardiuno :
 
 
 
 
Transmitter :
 
 
Features / Specifications :
1. 4 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
 
Technical Data :
Transmitter Module No.: TB420;
Power supply : 12V 23A battery (not included )  ,
 
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format: SCT2260  fixed code (compatiable for PT2262 SC2262 PT2260 PT2264 , can work with PT2272-M4 ,PT2272-T4,PT2272-L4 );
RC  Resistance : 4.7M; 
Transmit power : 200mW ;
 

Product Name: 15W Electrical isolation DC-DC Boost-Buck Converter 5V 6V 9V 18V 24V to -12V 15V Single voltage to double voltage Module
       
Packing list:
  
1 PCS 5-32 VDC to ±12V( 24V)/±15V( 30V) Isolated DC-DC Buck Converter
Description:
 
2 in 1 Isolated DC-DC Boost-Buck Converter 
 
Input Voltage Range: 5-32 VDC
 
Output Voltage :  ±12V/ 24V(MAX 700MA); ±15V/ 30V(MAX 550MA) 
 
Minimum Load Requirements: 0% (as 24V/ 30V Output), 10% (as -12/ -15 Output) 
 
Efficiency : 70% -88%  
 
Quiescent current : 68mA(Input 12V)
 
Low Noise : 50mV 
 
Hihg Accuracy ： /-1%  
 
Working frequency 400KHz   
 
Isolation (Input to Output): 1500VDC minimum (1 minute) 
 
Isolation Capacitance: 1200pF 
 
Short Circuit Protection 
 
Operating ambient temperature : -40~ 85 Degrees Celsius  
 
Storage Temperature Range: -55 to 125  Degrees Celsius  
 
Size : 68 x 44 x 16mm  
 
Weight :  39g(With terminal), 34g(no terminal) 
 
 
Pin description:
VIN    :  Input positive
GND  :  Input negative
EN     :  Input enable (NC or VIN enable, GND disabled)
V     :  Isolated output positive voltage
COM  :  Isolated output common
V-      :  Isolated output negative voltage
      
 
Applications
  
ADC/DAC/Operational Amplifier 
RS232 RS485 RS422 Bus
Audio equipment
Low power audio power supply
Car audio amplifier dual power board
LCD power supply
Instrumentation equipment
Instrumentation multimeter
    
Attention :
    
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
 
 
 
 
 
 
 
 
 
 

Product Name:  DC 5V-23V RS485 Modbus Rtu Temperature & humidity sensor Remote acquisition monitor replace DHT11 DHT22 DS18B20 PT100
 
 
 
Packing list:
1 pcs R414A01 RS485 Temperature and humidity senso  r(With a simple shell)    
   
description :
 
Working  voltage : DC 5-23V
 
Working  current : 8MA(12V)
 
MODBUS RTU protocol,03 Read,06 Write.
 
Serial baud rate : 9600(default),N,8,1
 
By modifying the RS485 address, up to 247 module s can be connected (more than 16 US ether485 repeater)
 
Temperature and humi dity sensor is DHT12
 
The voltage conversion module is CE018,a High-efficiency and Low-heat voltage Converter
 
Size : Module is 45 X 30 X 27MM,Shell is 50 X 35 X 22MM
Weight : Module is 11g,Shell is 10g
 
For more information, please contact us!!!
 
Typical application:
 
Indoor and outdoor temperature and humidity measurement
Temperature and humidity monitoring in vegetable garden
Weather forecasting, and monitoring
Temperature and Humidity Monitoring in Computer Room
Warehouse temperature and humidity monitoring
 
 Sensor parameters:
 
Wiring diagram:
 
 
 
 
 

Product Name:  DC 5V-23V RS485 Modbus Rtu Temperature & humidity sensor Remote acquisition monitor replace DHT11 DHT22 DS18B20 PT100
 
 
 
Packing list:
1 pcs R414A01 RS485 Temperature and humidity senso  r(With a simple shell)    
   
description :
 
Working  voltage : DC 5-23V
 
Working  current : 8MA(12V)
 
MODBUS RTU protocol,03 Read,06 Write.
 
Serial baud rate : 9600(default),N,8,1
 
By modifying the RS485 address, up to 247 module s can be connected (more than 16 US ether485 repeater)
 
Temperature and humi dity sensor is DHT12
 
The voltage conversion module is CE018,a High-efficiency and Low-heat voltage Converter
 
Size : Module is 45 X 30 X 27MM,Shell is 50 X 35 X 22MM
Weight : Module is 11g,Shell is 10g
 
For more information, please contact us!!!
 
Typical application:
 
Indoor and outdoor temperature and humidity measurement
Temperature and humidity monitoring in vegetable garden
Weather forecasting, and monitoring
Temperature and Humidity Monitoring in Computer Room
Warehouse temperature and humidity monitoring
 
 Sensor parameters:
 
Wiring diagram:
 
 
 
 
 

 
Product Name: 2 IN 1 8Ch Network Ethernet RS485 Relay Modbus RTU Slave TCP/IP UDP UART Switch Module PLC Industrial Control Board
 
Package inlcuded:
 1 PCS DC 12V 8 Channel RS485/TCP Modbus Slave Relay Module
 
 
Description:
 
1: Working voltage : DC 12V
 
2: Standby current (All relays closed) 13MA, 1 relay open 41MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 226MA
 
3:Communication interface: RS485 interface / network interface (optional)
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' 6 Commands
 
5: MODBUS RTU command, Support 03 06 16 function code
 
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 :MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 :Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 :The default baud rate is 9600BPS. The baud rate can be set by command: 1200 2400 4800 9600 19200BPS
 
10 :The data sending and returning time can be set, with a maximum value of 1000ms
 
11 :Size: 145 * 90 * 40mm(with shell)
12: Weight: 138g(Only PCB Board);230g(with shell)
 
13: Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
For more information, please contact me
 
Application
 
PLC Output expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
Ethernet Controller, TCP/IP Controller
Wiring diagram
 
 

 
Product Name: DC 12V 2CH RKE Secure Remote Keyless Entry System Remote Controller Rolling Code Keyfob Kit for Motor Forward and reverse
 
 
 
Package inlcuded:
1 PCS 433M DC 12V 2CH Rolling code Relay Board Module
1 PCS 433M HCS301 Remote Control(Does not include 12V 27A battery)
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 13MA, 1 relay open 41MA, 2 relays open 69MA
3. Wireless Receiving frequency : 433Mhz ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. size (including shell) 62*58*30mm;
8. weight : 51 grams;
9. Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door
Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
PTZ Camera
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Product number : RC43A04
Rolling Code (HCS301)
Use 12V 27A battery, battery not included
Weight : 28gram.

 
 
Product Name: DC 12V 24V 8DI 8DO Multifunction RS485 Modbus RTU Relay Module Support 01 05 15 02 03 06 16 Function Code Switch Control Board
 
 
 
Package inlcuded:
 
1PCS DC 12V/24V 8DI 8DO Modbus RTU RS485 Relay Module
 
 
Description:
 
1:DC 12V (12V Version),DC 24V (24V Version)
 
2.Standby current (all relays closed) 14MA, 1 relay open 40MA, 2 relays open 68MA, 3 relays open 96MA,4 relays open 122MA,5 relays open 149MA,6 relays open 177MA, 7 relays open 202MA,8 relays open 226MA
3:8 photoelectric isolation Input ports (NPN low level active ).
The input-output relationship can be set to various association modes through instructions(Self-lockingdefault)/Interlocking/Momentary/Interlocking/Output=Input)
4: Support standard Modbus RTU command, function code, write 05/06/15/16 read 01/02/03
 
5: With hardware reset function, with TVS anti-surge protection
 
6 8 opto-isolated inputs (NPN), 8 relay outputs (upgraded relays, more durable)
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll''Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
8 The default baud rate is 9600BPS. The baud rate can be selected by Conmand 2400 4800 9600 19200 38400 57600 115200BPS
 
10 The parity can be none parity, even parity and odd parity
 
11 The data sending and returning time can be set,with a maximum value of 1000ms
 
12 Size: 136 * 72 * 12mm(Only PCB Board);138 * 82*40mm(with Din Rail Box)
13 Weight: 143g(Only PCB Board);239g(with Din Rail Box)
14 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
Upgraded Features:
MODBUS RTU Function Code 01 05 15 02 03 06 16
Support more input-output relationships
Support more baud rates, can modify the parity bit
Hardware reset to factory settings (RESET jumper)
Upgraded relays (more durable)
TVS anti-surge protection
For more information, please contact me
Application
 
PLC RS485 IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ Camera
Security Monitoring
Identification system;
LED Lamp Drivers
Automatic curtain control
Battery Test Detection System
DIN rail Box parameters:
Product model: UM72
Color: Grey
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 136 mm PCB boards
Net weight: 99g
Installation: DIN35 and C45 rail
 
 
 
 

 
 
Product Name: DC 12V 24V 8DI 8DO Multifunction RS485 Modbus RTU Relay Module Support 01 05 15 02 03 06 16 Function Code Switch Control Board
 
 
 
Package inlcuded:
 
1PCS DC 12V/24V 8DI 8DO Modbus RTU RS485 Relay Module
 
 
Description:
 
1:DC 12V (12V Version),DC 24V (24V Version)
 
2.Standby current (all relays closed) 14MA, 1 relay open 40MA, 2 relays open 68MA, 3 relays open 96MA,4 relays open 122MA,5 relays open 149MA,6 relays open 177MA, 7 relays open 202MA,8 relays open 226MA
3:8 photoelectric isolation Input ports (NPN low level active ).
The input-output relationship can be set to various association modes through instructions(Self-lockingdefault)/Interlocking/Momentary/Interlocking/Output=Input)
4: Support standard Modbus RTU command, function code, write 05/06/15/16 read 01/02/03
 
5: With hardware reset function, with TVS anti-surge protection
 
6 8 opto-isolated inputs (NPN), 8 relay outputs (upgraded relays, more durable)
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll''Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
8 The default baud rate is 9600BPS. The baud rate can be selected by Conmand 2400 4800 9600 19200 38400 57600 115200BPS
 
10 The parity can be none parity, even parity and odd parity
 
11 The data sending and returning time can be set,with a maximum value of 1000ms
 
12 Size: 136 * 72 * 12mm(Only PCB Board);138 * 82*40mm(with Din Rail Box)
13 Weight: 143g(Only PCB Board);239g(with Din Rail Box)
14 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
Upgraded Features:
MODBUS RTU Function Code 01 05 15 02 03 06 16
Support more input-output relationships
Support more baud rates, can modify the parity bit
Hardware reset to factory settings (RESET jumper)
Upgraded relays (more durable)
TVS anti-surge protection
For more information, please contact me
Application
 
PLC RS485 IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ Camera
Security Monitoring
Identification system;
LED Lamp Drivers
Automatic curtain control
Battery Test Detection System
DIN rail Box parameters:
Product model: UM72
Color: Grey
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 136 mm PCB boards
Net weight: 99g
Installation: DIN35 and C45 rail
 
 
 
 

 
Product Name: DC 12V 8Ch RS485 Bus Modbus RTU Relay Module with TVS protected
 
 
 
Package inlcuded:
  1PCS DC 12V Channel RS485 Relay Switch Module Board
 
 
Description:
 
1: Working voltage DC 12V;
2: Standby current (all relays closed) 12MA, 1 relay open 40MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 225MA
 
3: Enhanced RS485 interface protection (TVS)
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' 6 Commands
5: MODBUS RTU command, Support 03 06 16 function code
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 The default baud rate is 9600BPS. The baud rate can be selected through jumpers: 2400 4800 9600 19200BPS
 
10 Size: 145*90*40mm
 
11 Weight: 218g
 
12 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
For more information, please contact me
 
Application
 
PLC Output expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
 
 
 

 
Product Name: DC 12V 8Ch RS485 Bus Modbus RTU Relay Module with TVS protected
 
 
 
Package inlcuded:
  1PCS DC 12V Channel RS485 Relay Switch Module Board
 
 
Description:
 
1: Working voltage DC 12V;
2: Standby current (all relays closed) 12MA, 1 relay open 40MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 225MA
 
3: Enhanced RS485 interface protection (TVS)
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' 6 Commands
5: MODBUS RTU command, Support 03 06 16 function code
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 The default baud rate is 9600BPS. The baud rate can be selected through jumpers: 2400 4800 9600 19200BPS
 
10 Size: 145*90*40mm
 
11 Weight: 218g
 
12 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
For more information, please contact me
 
Application
 
PLC Output expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
 
 
 

Brand Name : eletechsup
Certification : None
Origin : CN(Origin)
is_customized : Yes
Voltage : 12V
Model Number : IO55C02
Protect Feature : Epoxy
Power Source : DC
Usage : General Purpose
Product Name:200W 12V 24V DC Motor Driver Module 433M Wireless Remote Controller Forward Reverse Limit Speed Board
Product Included:
1 * Motor Speed Controller (include speed knob)and 1*remote control(Does not include 12V 23A battery)
OR 1*Remote control(Does not include 12V 23A battery)
OR 1 * Motor Speed Controller(include speed knob)
Note: Please use the remote control we sell, otherwise it may not be compatible with the remote control.
Features:
1. Provides variable speed capability for DC motor, also provides limit function.
2. Achieves start, stop, speed up and down, positive and reverse rotation RC controlled.
3. DC Motor Speed Controller can achieve simple automatic functions.
4. It can remote control the speed up and down, positive and reversing rotation and stop of the brushed DC motor.
5. It owns powerful function, stable performance and beautiful appearance.
Motor Speed Controller Description:
•Applicable voltage: DC 12V~30V (DC power supply power ≥ motor power x1.3)
•Wireless receiving sensitivity: -108dBm
•Decoding type: fixed code, can be adapted to up to 32 remote controls
•Working modes: click to move, self-locking
•Size(including shell): 115*90*40mm
•Weight (including speed control knob): 194.1g
•Applicable motor: brushed DC motor, rated power of 24V DC motor <100W, limit value 200W, rated power of 12V DC motor <50W, limit value 100W
•Speed regulation function: After the governor is powered on, both the knob and the remote control can control the speed. If the adjustment knob exceeds 5% of the range, the knob speed regulation mode is preferred, and the remote control speed regulation mode is preferred to use the remote control speed regulation
Remote Control Description:
•Remote model : TB453(fixed code)
•Power supply : 12V 23A battery replacable (This remote doesnot have a battery , Please buy in your local market )
•Operating current: ≤ 9mA
•Oscillation mode: SAW resonator
•Modulation mode:ASK
•Operating frequency:433.92MHZ
•Frequency deviation:± 150Hz (max)
•Encoding format: Fixed Code ( EV1527)
•Transmit power: 10 mW
•Weight : 36.9g
Operating mode:
Speed knob:

Product Name: Nuvoton C51 MCU Development Board N76E003 MS51FB9AE LED Infrared Remote Control Optocoupler RS485 Relay Module
Packing included:
1 PCS MS51FB9AE Development board Board
1 PCS SP485 USB to RS485 Converter
1 PCS TB441 Infrared remote control
MS51FB9AE(Compatible with N76E003) Development board​:
1 Operating Voltage : DC 12V
2 Operating Current : 9-13MA
3 IR remote control Working distance: 8-16 meters (receiver sensitivity ≥0.5mW / m2)
4 Major equipment: 4Relay ,1LED Display
5 Size: 80 x 65 x 138mm
6 Weight : 76.7g
The development board adopts MS51FB9AE(Compatible with N76E003) chip produced by Nuvoton Technology as the main control, with optocoupler, relay, digital tube, LED light, button, RS485 and Infrared receiver as peripherals, and provides a program download interface, users can control all peripherals through the main control. The development board uses 12V DC power supply.
The description of TB441 Infrared remote control:
Transmission / coding: NEC coding
IRED: Infrared
Wavelength: 950nm
Power supply: DC 3V
Working voltage: 2.2-3.4V
Working current: ≥10mA
Static current: ≥1uA
Transmit power: 90 mW / sr typ.
Working distance: 8-15 meters (receiver sensitivity ≥0.5mW / m2)
Frequency: 38 kHz
Battery: CR2025(Not included)
Operating temperature: 55 ~ -45 or specific specifications
Storage temperature: -25 ~ 55 or specific specifications
Size : 85 x 40 x 7mm
Weight : 11g
The description of SP485 USB to RS485 Converter:
This is Industrial grade USB TO RS485 Converter
The USB driver IC is CH340E, stable performance, fully compatible with USB1.1,USB2.0,USB3.0 , baud rate up to 256 kbps;
The RS485 bus IC is SP485,this is Industrial grade RS485 conversion IC
USB to RS485 serial port, 4 pin pin assignment as below : 5V GND A B-
Uses : CH340 replace FT232 CP2102 PL2303 for PLC PTZ RS485 MCU etc. RS485 Bus Device
Size : 36 x 16 x 12mm
Weight : 8g
Supports the following Windows OSes:
Windows 98SE
Windows ME
Windows 2000 SP4
Windows XP SP2 and above (32 & 64 bit)
Windows Server 2003 (32 & 64 bit)
Windows Server 2008 / 2008 R2 (32 & 64 bit)
Windows Vista (32 & 64 bit)
Windows 7 (32 & 64 bit)
Windows 8
Windows 8.1
Windows 10
Linux OS
​MAC OS

Product Name: Nuvoton C51 MCU Development Board N76E003 MS51FB9AE LED Infrared Remote Control Optocoupler RS485 Relay Module
Packing included:
1 PCS MS51FB9AE Development board Board
1 PCS SP485 USB to RS485 Converter
1 PCS TB441 Infrared remote control
MS51FB9AE(Compatible with N76E003) Development board​:
1 Operating Voltage : DC 12V
2 Operating Current : 9-13MA
3 IR remote control Working distance: 8-16 meters (receiver sensitivity ≥0.5mW / m2)
4 Major equipment: 4Relay ,1LED Display
5 Size: 80 x 65 x 138mm
6 Weight : 76.7g
The development board adopts MS51FB9AE(Compatible with N76E003) chip produced by Nuvoton Technology as the main control, with optocoupler, relay, digital tube, LED light, button, RS485 and Infrared receiver as peripherals, and provides a program download interface, users can control all peripherals through the main control. The development board uses 12V DC power supply.
The description of TB441 Infrared remote control:
Transmission / coding: NEC coding
IRED: Infrared
Wavelength: 950nm
Power supply: DC 3V
Working voltage: 2.2-3.4V
Working current: ≥10mA
Static current: ≥1uA
Transmit power: 90 mW / sr typ.
Working distance: 8-15 meters (receiver sensitivity ≥0.5mW / m2)
Frequency: 38 kHz
Battery: CR2025(Not included)
Operating temperature: 55 ~ -45 or specific specifications
Storage temperature: -25 ~ 55 or specific specifications
Size : 85 x 40 x 7mm
Weight : 11g
The description of SP485 USB to RS485 Converter:
This is Industrial grade USB TO RS485 Converter
The USB driver IC is CH340E, stable performance, fully compatible with USB1.1,USB2.0,USB3.0 , baud rate up to 256 kbps;
The RS485 bus IC is SP485,this is Industrial grade RS485 conversion IC
USB to RS485 serial port, 4 pin pin assignment as below : 5V GND A B-
Uses : CH340 replace FT232 CP2102 PL2303 for PLC PTZ RS485 MCU etc. RS485 Bus Device
Size : 36 x 16 x 12mm
Weight : 8g
Supports the following Windows OSes:
Windows 98SE
Windows ME
Windows 2000 SP4
Windows XP SP2 and above (32 & 64 bit)
Windows Server 2003 (32 & 64 bit)
Windows Server 2008 / 2008 R2 (32 & 64 bit)
Windows Vista (32 & 64 bit)
Windows 7 (32 & 64 bit)
Windows 8
Windows 8.1
Windows 10
Linux OS
​MAC OS

433MHz  1 Transmitter module & 4 Wireless Relay Controller for Arduiuo UNO MEGA2560
 
We provide Arduiuo sample code , please contact after your order after your purchase  . 
 
 
 
Qty:
 
1 PCS 433M Wireless transmitter module( Does not include Arduiuo UNO );
4 PCS 433M  1 channels relay switch;
 
 
Wireless transmitter module  connected with  Arduiuo uno( replace PT2262 Remote Keyfob)
 
USE: 
 
 
 
Software control:
How to use:send "a" trigger A channel relay,send "b" trigger A channel relay,Etc.
 
 
arduiuo core fragment( complete code please Request) :
  
//Author: Mr Liu
//Arduiuo 1.0
//Arduiuo uno R3
//Making a wireless remote control with arduiuo
  
...
 
//send:8 Address Bits, 4 Data Bits, Sync bit
void send_data()
 
void setup() {
  // initialize the LED pin as an output:
  pinMode(ledPin, OUTPUT); 
   // initialize the encoder DOUT pin as an output
  pinMode(data_out, OUTPUT);
 
  Serial.begin(9600);
}
void loop()
{
  ...
  
  while(1)
  {
    //get key from pc serial port
    while (Serial.available() > 0) 
    {
        keydata = Serial.read();
        receive_flag = 1;
        delay(2);
    }
   
    if(receive_flag == 1)//if get key,send key
    {
     
    receive_flag = 0;
   
    if((keydata == 'a') || (keydata == 'A'))//trigger A channel relay.
    {
      Temporary[2] = 0xC0;// 0xC0 is A button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
       Serial.println(".....trigger A channel relay.....");
    }
    else if((keydata == 'b') || (keydata == 'B'))//trigger B channel relay.
    {
      Temporary[2] = 0x30;// 0x30 is B button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
      Serial.println(".....trigger B channel relay.....");
    }
     else if((keydata == 'c') || (keydata == 'C'))//trigger C channel relay.
     {
      Temporary[2] = 0x0C;// 0x0C is C button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
      Serial.println(".....trigger C channel relay.....");
     
     }
     else if((keydata == 'd') || (keydata == 'D'))//trigger D channel relay.
     {
      Temporary[2] = 0x03;// 0x03 is D button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
      Serial.println(".....trigger D channel relay.....");
     }
    
    ...
  
  }
}

433MHz  1 Transmitter module & 4 Wireless Relay Controller for Arduiuo UNO MEGA2560
 
We provide Arduiuo sample code , please contact after your order after your purchase  . 
 
 
 
Qty:
 
1 PCS 433M Wireless transmitter module( Does not include Arduiuo UNO );
4 PCS 433M  1 channels relay switch;
 
 
Wireless transmitter module  connected with  Arduiuo uno( replace PT2262 Remote Keyfob)
 
USE: 
 
 
 
Software control:
How to use:send "a" trigger A channel relay,send "b" trigger A channel relay,Etc.
 
 
arduiuo core fragment( complete code please Request) :
  
//Author: Mr Liu
//Arduiuo 1.0
//Arduiuo uno R3
//Making a wireless remote control with arduiuo
  
...
 
//send:8 Address Bits, 4 Data Bits, Sync bit
void send_data()
 
void setup() {
  // initialize the LED pin as an output:
  pinMode(ledPin, OUTPUT); 
   // initialize the encoder DOUT pin as an output
  pinMode(data_out, OUTPUT);
 
  Serial.begin(9600);
}
void loop()
{
  ...
  
  while(1)
  {
    //get key from pc serial port
    while (Serial.available() > 0) 
    {
        keydata = Serial.read();
        receive_flag = 1;
        delay(2);
    }
   
    if(receive_flag == 1)//if get key,send key
    {
     
    receive_flag = 0;
   
    if((keydata == 'a') || (keydata == 'A'))//trigger A channel relay.
    {
      Temporary[2] = 0xC0;// 0xC0 is A button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
       Serial.println(".....trigger A channel relay.....");
    }
    else if((keydata == 'b') || (keydata == 'B'))//trigger B channel relay.
    {
      Temporary[2] = 0x30;// 0x30 is B button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
      Serial.println(".....trigger B channel relay.....");
    }
     else if((keydata == 'c') || (keydata == 'C'))//trigger C channel relay.
     {
      Temporary[2] = 0x0C;// 0x0C is C button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
      Serial.println(".....trigger C channel relay.....");
     
     }
     else if((keydata == 'd') || (keydata == 'D'))//trigger D channel relay.
     {
      Temporary[2] = 0x03;// 0x03 is D button key
      digitalWrite(ledPin, HIGH);//Turn on led
      send_data();//send code word
      Serial.println(".....trigger D channel relay.....");
     }
    
    ...
  
  }
}

Kit No. : RT404
 
 
Qty : 1 pcs PT2262 transmitter module and 1 pcs 4 channels relay switch ;
 
 
Transmitter :
 
 
Features / Specifications :
1. 4 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
 
Technical Data :
Transmitter Module No.: TB420;
Power supply : 12V 23A battery (not included ) , 
 
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format: SCT2260 fixed code (compatiable for PT2262 SC2262 PT2260 PT2264 , can work with PT2272-M4 ,PT2272-T4,PT2272-L4 );
RC Resistance : 4.7M;
Transmit power : 200mW ;
 
Relay receiver :
 
Typical applications:
DC 12V Home lighting system
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lights, fans, motors and other DC 12V
 
 
Wiring Diagram 2:
DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lights, fans, motors and other DC AC equipment
 
 
Wiring Diagram 3:
All kinds of motor reversing control: DC 1-110V or AC 85-265V DC/AC Motor
 
 
 
Product Name : DC 12V 4CH 433MHz Delay RF Wireless Relay Controller For PT2262 EV1527 Encoder
 
Module No.: CE-RF22A04
Packing list:
1 PCS 433M DC 12V 4 Channel Multifunction Wireless Controller
Features:
1 Operating voltage : DC 12V
2 Operating Current: Standby current (all relays closed) 15MA, 1 relay open 42MA, 2 relays open 62MA, 3 relays open 94MA, 4 relays open 121MA
3 Operating frequency: 433.92M;
 
4 Receiver sensitivity : -108dBm
 
5 Decode : learning code, can be adapted EV1527 / PT2262(Click here)and compatible remote control, you can store up to 8 remote control
 
6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; Delay adjustable from 0.1 to 100 seconds, 0.1 seconds Resolution.
7 Size(Including housing)75*54*28mm
8 Weight: 77g
9 Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC
Advantage :
1: Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 OR Pt2262 remotes to re-learn;
 
 
Work mode
Delay mode user guide :
 
1 In delay mode(Mode 3),with a suitable screwdriver and gently rotating adjustable resistance;Clockwise, increasing delay,Counter-clockwise, the delay is reduced
 
2 Delay adjustable from 0.1 to 100 seconds, 0.1 seconds Resolution.
Glossary:
NO : Relay normally open contact
COM : Relay common contact
NC : Relay normally closed contact
Open : NO connection COM, NC disconnect COM
Close : NO disconnect COM, NC connection COM
Momentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A; the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;
Toggle : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as B. Every Channel is Independent ;
Latched : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2 is Close.
Press transmitter button B, the receiver Channel 2 is Open, the Channel 1 is Close.
Delay : Press the Transmitter button A, the receiver Channel 1 is Open,After a set time delay, the receiver Channel 1 is Close, the same as B ,Every Channel is Independent;
If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay Close
 
Adapter remote control (learning remote control):
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
 
 
Clean code: press the button and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
 
 
Step 1 (into the learning mode): Press the button (about 1 second), LED off;
 
Step 2 (adapter channel 1): Then press the first button on the remote control, LED flashes four times off, then learning the first button value
 
Step 3 (Adaptation Channel 2): Then press the second button on the remote control, LED flashes four times brighter, then learned two key values
 
Step 4 (Adaptation Channel 3): Then press the third button on the remote control, LED flashes four times brighter, then learned two key values
 
Step 5 (Adaptation Channel 4): Then press the fourth button on the remote control, LED flashes four times brighter, then learned two key values
 

Kit No. : RT404
 
 
Qty : 1 pcs PT2262 transmitter module and 1 pcs 4 channels relay switch ;
 
 
Transmitter :
 
 
Features / Specifications :
1. 4 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
 
Technical Data :
Transmitter Module No.: TB420;
Power supply : 12V 23A battery (not included ) , 
 
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format: SCT2260 fixed code (compatiable for PT2262 SC2262 PT2260 PT2264 , can work with PT2272-M4 ,PT2272-T4,PT2272-L4 );
RC Resistance : 4.7M;
Transmit power : 200mW ;
 
Relay receiver :
 
Typical applications:
DC 12V Home lighting system
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lights, fans, motors and other DC 12V
 
 
Wiring Diagram 2:
DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lights, fans, motors and other DC AC equipment
 
 
Wiring Diagram 3:
All kinds of motor reversing control: DC 1-110V or AC 85-265V DC/AC Motor
 
 
 
Product Name : DC 12V 4CH 433MHz Delay RF Wireless Relay Controller For PT2262 EV1527 Encoder
 
Module No.: CE-RF22A04
Packing list:
1 PCS 433M DC 12V 4 Channel Multifunction Wireless Controller
Features:
1 Operating voltage : DC 12V
2 Operating Current: Standby current (all relays closed) 15MA, 1 relay open 42MA, 2 relays open 62MA, 3 relays open 94MA, 4 relays open 121MA
3 Operating frequency: 433.92M;
 
4 Receiver sensitivity : -108dBm
 
5 Decode : learning code, can be adapted EV1527 / PT2262(Click here)and compatible remote control, you can store up to 8 remote control
 
6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; Delay adjustable from 0.1 to 100 seconds, 0.1 seconds Resolution.
7 Size(Including housing)75*54*28mm
8 Weight: 77g
9 Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC
Advantage :
1: Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 OR Pt2262 remotes to re-learn;
 
 
Work mode
Delay mode user guide :
 
1 In delay mode(Mode 3),with a suitable screwdriver and gently rotating adjustable resistance;Clockwise, increasing delay,Counter-clockwise, the delay is reduced
 
2 Delay adjustable from 0.1 to 100 seconds, 0.1 seconds Resolution.
Glossary:
NO : Relay normally open contact
COM : Relay common contact
NC : Relay normally closed contact
Open : NO connection COM, NC disconnect COM
Close : NO disconnect COM, NC connection COM
Momentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A; the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;
Toggle : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as B. Every Channel is Independent ;
Latched : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2 is Close.
Press transmitter button B, the receiver Channel 2 is Open, the Channel 1 is Close.
Delay : Press the Transmitter button A, the receiver Channel 1 is Open,After a set time delay, the receiver Channel 1 is Close, the same as B ,Every Channel is Independent;
If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay Close
 
Adapter remote control (learning remote control):
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
 
 
Clean code: press the button and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
 
 
Step 1 (into the learning mode): Press the button (about 1 second), LED off;
 
Step 2 (adapter channel 1): Then press the first button on the remote control, LED flashes four times off, then learning the first button value
 
Step 3 (Adaptation Channel 2): Then press the second button on the remote control, LED flashes four times brighter, then learned two key values
 
Step 4 (Adaptation Channel 3): Then press the third button on the remote control, LED flashes four times brighter, then learned two key values
 
Step 5 (Adaptation Channel 4): Then press the fourth button on the remote control, LED flashes four times brighter, then learned two key values
 

 
 
Typical applications:
  
Remote control switch
Smart Home / Home Automation
LED lighting
3d printer
Fluorescent lamp
220V AC Motor(<500W)
 
 
 
Product Name : 433Mhz 4 Key EV1527 Remote Control 4pcs one Channel Relay Wireless Controller AC Smart Switch kit
 
Packing list:
4 PCS 433M 220V 1 Channel  Relay Receiver
1 PCS 433M 4 Key Remote Control
 
 
Technical indicators:
 
Operating voltage : AC 180~250V(Default 220V);
Operating frequency : 433.92MHz ;
Receiver sensitivity :-95dB;
Decoder  : EV1527 PT2262 PT2264;
Momentary / Latch / Toggle selectable (defult is  Toggle  , Latch Mode need 2 buttons handsender );
Input : 220V;
Output : 220V With Switch;
Receiver size: 62 * 35 * 22 mm;
Max load : 500W;
 
Advantage :
1: Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 OR Pt2262 remotes to re-learn;
 
Work mode (programmable )
singnal Inter-locking (Latch)
singnal Self-locking (Toggle   is defult )
singnal Non-locking (Momentary)
 
Work mode explanation:
Momentary------------Press the Transmitter button A, the receiver relay A is ON, release button A; the receiver relay A is OFF, the same as B/C/D ,Every channel is Independent ;
 
Toggle---------------Press transmitter button A for 1 time , the receiver relay A is ON, press button A again, the receiver relay A is OFF, the same as B/C/D. Every channel is Independent ;
  
Latched------------------
Press transmitter button A, the receiver relay A is ON, the relay B/C/D is OFF.
Press transmitter button B, the receiver relay B is ON, the relay A/C/D is OFF.
Press transmitter button C, the receiver relay C is ON, the relay A/B/D is OFF
Press transmitter button D, the receiver relay D is ON, the relay A/B/C is OFF.
 
Normally, we would adapter remote control and receiver.
If the item you received has not been adapted Or you need to add accessories, Please follow the instructions below
 
Program steps :
1: keep pressing learning key on the receiver controller ,
LED turn on after 2 second , then turn off after 4 second, then the receiver controller enter programming state , but not release the finger , still keep pressing the learning button , 
LED blink once after 2 second , release the finger on learing key , it is Momentary mode , 
or still keep pressing learing key ,
LED blink twice after 2 second , release the finger on learing key , it is Toggle mode ,
or still keep pressing learing key ,
LED blink 3 times after 2 second , release the finger on learing key , it is Latch mode ,
 
Learning method and steps
Keep pressing learnig key on receiver controller board , LED turn on after 2 seconds , release the finger on learning key , press the key on remote , work state LED blink 3 times , it means learnig successfully ;
Clear the deposit information
Keep pressing learnig key on receiver controller board, LED turn on after 2 seconds , then turn off after 4 seconds , it means clearing successfully .
 
  
433M 4 Button EV1527 Remote Control:
 
Technical Data :
 
Power supply : 12V 27A battery  replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current:  ≤ 12mA ;
Oscillation mode:  SAW resonator ;
Oscillation resistor : 330K
Modulation mode: ASK ;
Operating frequency: 433.92MHz  ;
Frequency dev iation: ±0.2MHz ;
Encoding format: Million  Group Code (  EV1527 ) ;
Transmit power: 10 mW.
Data Rate : 50~60KHZ;