Elektromos motorok

Driver Board Stepper Motors 28BYJ-48 LED Wear-resistant Parts 5V Geared
Features:
*100% brand new and high quality
*Made of high quality material, durable and practical to use
*5V 4-Phase Geared Stepper Motor with ULN2003 Driver Board 28BYJ-48 For Arduino
*DC 5V 4-phase stepper motor driver test module board for Arduino
*The driver board has A, B, C, D four-phase LEDs to indicate the working state of the stepper motor
*Stepper motor with standard interface, can be directly plugged and used
*Wear-resistant and reliable
Specification:
*Color: As pictures show
*Rated voltage: DC5V 4 phase
*Step angle: 5.625 x 1/64
*No-load pull-in frequency: > 600Hz
*No-load pull-out frequency: > 1000Hz
*Pulling torque: > 34.3mN.m (120Hz)
*Brake torque: > 34.3mN.m
*DC resistance: 200Ω±7% (25C)
*Insulation resistance: >10MΩ (500V)
*Dielectric strength: 600V AC / 1mA / 1s
*Insulation class: A
*Temperature rise: <40K (120Hz)
*Noise: <40dB (120Hz, no load, 10cm)
*Diameter: 2.5 cm (Approx.)
*Width: 2 cm (Approx.)
Package Contents:
5*Drive Boards
5*Stepper Motors
Note:
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2.Please allow slight manual measurement deviation for the data.

A range of miniature gears for use with many types of model motors. The kit consists of 3 different types of gear. a) Standard cogs 2x 9mm, 2x 16mm, 2x22mm, 2x 31mm. B) Split Cogs, with an intermediate 10 tooth gear 2x16mm, 2x22mm C) 6mm Worm Gears 2x6mm

A low cost, reliable motor rated at 3V with a high stall talk which is ideal for robotics, toys, models and actuation.
* Rotational Direction: Clockwise
* Min Operating Voltage: 1.5V
* Max Operating Voltage: 4.5V
* Rotational Speed (No Load): 6,700

A V-Groove Pulley made from Plastic Material with a 10mm diameter, and including a motor spindle stand-off. Designed for interference fit on to a 2mm shaft and is suitable for use with miniature motors. Ideal for use inapplications such as robot and model

A V-Groove Pulley made from Plastic Material with a 20mm diameter, and including a motor spindle stand-off. Designed for interference fit on to a 3.2mm shaft and is suitable for use with miniature motors. Ideal for use inapplications such as robot and mod

A plastic motor mount for use with Spiratronics motors (order codes XA2-017 & XB2-016). The device has a self adhesive pad on the bottom for affixing where required and then the motor simply clips in allowing very rapid motor mounting in many applications

A waterproof unit which can be used to create a flow of water which makes it ideal to be used in water based models to supply movements. The motor pulls apart to insert and change the battery and the power is switched on by twisting the battery. A suction

A robust module featuring a motor, with a worm-drive nylon gearbox which is ideal for model making where a high torque is required, for example on driven wheels on a vehicle or robot. The gearbox is pre-drilled to allow easy screw fitting to a flat surfac

A low cost but high performance 3V motor gearbox. The housing is made from clear plastic and the output shaft has a diameter of 4mm.
Download a Full Datasheet

A low inertia motor coupled to a 27:1 gearbox offering an output of around 25rpm from an input of approximately 4.5V
Diameter:: 25mm
Gear Ratio:: 27:1
Length:: 36mm
Maximum Speed:: 25rpm
Shaft Diameter:: 2mm
Voltage Rating:: 4.5V
Width:: 15mm