Tesztberendezés alkatrészei és tartozékai

0.96 inch OLED 4Pin IIC Serial
Interface type: IIC interface
Pin definition: GND, VDD, SCK, SDA
1:GND(OLED power supply)
2:VDD (OLED 3.3~5V)
3:SCK(OLED IIC Clock line)
4:SDA(OLED IIC Cable)

0.96 inch OLED 7Pin SPI/IIC Serial
Driver chip SSD1306
Support interface SPI/IIC
Resolution 128×64
Display size 0.96 inches
Display color: white light/blue light/yellow-blue color
Dimensions 27.5×27.8 (mm)
Glass size 26.7×19.26×1.4 (mm)
Display area 21.74(W)×10.864(mm)
Point pitch 0.17×0.17 (mm)
Point size 0.15×0.15 (mm)
Number of pins 7 pins
Power consumption Normal display power consumption is 21mA-28MAX
Working current The current is about 20ma during normal operation, and the current is at ua level when sleeping
Perspective full perspective
Working temperature -20℃~70℃
Storage temperature -30℃~80℃
Working voltage 2.8-5.5V
1 GND Power ground
2 VDD power supply positive (2.8-5.5V)
3 SCK clock line
4 SDA data cable
5 RES reset line
6 DC data/command
7 CS Chip Select

0.96 inch OLED 4Pin IIC Serial
Interface type: IIC interface
Pin definition: GND, VDD, SCK, SDA
1:GND(OLED power supply)
2:VDD (OLED 3.3~5V)
3:SCK(OLED IIC Clock line)
4:SDA(OLED IIC Cable)

0.96 inch OLED 7Pin SPI/IIC Serial
Driver chip SSD1306
Support interface SPI/IIC
Resolution 128×64
Display size 0.96 inches
Display color: white light/blue light/yellow-blue color
Dimensions 27.5×27.8 (mm)
Glass size 26.7×19.26×1.4 (mm)
Display area 21.74(W)×10.864(mm)
Point pitch 0.17×0.17 (mm)
Point size 0.15×0.15 (mm)
Number of pins 7 pins
Power consumption Normal display power consumption is 21mA-28MAX
Working current The current is about 20ma during normal operation, and the current is at ua level when sleeping
Perspective full perspective
Working temperature -20℃~70℃
Storage temperature -30℃~80℃
Working voltage 2.8-5.5V
1 GND Power ground
2 VDD power supply positive (2.8-5.5V)
3 SCK clock line
4 SDA data cable
5 RES reset line
6 DC data/command
7 CS Chip Select

0.96 inch OLED 4Pin IIC Serial
Interface type: IIC interface
Pin definition: GND, VDD, SCK, SDA
1:GND(OLED power supply)
2:VDD (OLED 3.3~5V)
3:SCK(OLED IIC Clock line)
4:SDA(OLED IIC Cable)

0.96 inch OLED 7Pin SPI/IIC Serial
Driver chip SSD1306
Support interface SPI/IIC
Resolution 128×64
Display size 0.96 inches
Display color: white light/blue light/yellow-blue color
Dimensions 27.5×27.8 (mm)
Glass size 26.7×19.26×1.4 (mm)
Display area 21.74(W)×10.864(mm)
Point pitch 0.17×0.17 (mm)
Point size 0.15×0.15 (mm)
Number of pins 7 pins
Power consumption Normal display power consumption is 21mA-28MAX
Working current The current is about 20ma during normal operation, and the current is at ua level when sleeping
Perspective full perspective
Working temperature -20℃~70℃
Storage temperature -30℃~80℃
Working voltage 2.8-5.5V
1 GND Power ground
2 VDD power supply positive (2.8-5.5V)
3 SCK clock line
4 SDA data cable
5 RES reset line
6 DC data/command
7 CS Chip Select

0.96 inch OLED 4Pin IIC Serial
Interface type: IIC interface
Pin definition: GND, VDD, SCK, SDA
1:GND(OLED power supply)
2:VDD (OLED 3.3~5V)
3:SCK(OLED IIC Clock line)
4:SDA(OLED IIC Cable)

0.96 inch OLED 7Pin SPI/IIC Serial
Driver chip SSD1306
Support interface SPI/IIC
Resolution 128×64
Display size 0.96 inches
Display color: white light/blue light/yellow-blue color
Dimensions 27.5×27.8 (mm)
Glass size 26.7×19.26×1.4 (mm)
Display area 21.74(W)×10.864(mm)
Point pitch 0.17×0.17 (mm)
Point size 0.15×0.15 (mm)
Number of pins 7 pins
Power consumption Normal display power consumption is 21mA-28MAX
Working current The current is about 20ma during normal operation, and the current is at ua level when sleeping
Perspective full perspective
Working temperature -20℃~70℃
Storage temperature -30℃~80℃
Working voltage 2.8-5.5V
1 GND Power ground
2 VDD power supply positive (2.8-5.5V)
3 SCK clock line
4 SDA data cable
5 RES reset line
6 DC data/command
7 CS Chip Select

0.96 inch OLED 4Pin IIC Serial
Interface type: IIC interface
Pin definition: GND, VDD, SCK, SDA
1:GND(OLED power supply)
2:VDD (OLED 3.3~5V)
3:SCK(OLED IIC Clock line)
4:SDA(OLED IIC Cable)

0.96 inch OLED 7Pin SPI/IIC Serial
Driver chip SSD1306
Support interface SPI/IIC
Resolution 128×64
Display size 0.96 inches
Display color: white light/blue light/yellow-blue color
Dimensions 27.5×27.8 (mm)
Glass size 26.7×19.26×1.4 (mm)
Display area 21.74(W)×10.864(mm)
Point pitch 0.17×0.17 (mm)
Point size 0.15×0.15 (mm)
Number of pins 7 pins
Power consumption Normal display power consumption is 21mA-28MAX
Working current The current is about 20ma during normal operation, and the current is at ua level when sleeping
Perspective full perspective
Working temperature -20℃~70℃
Storage temperature -30℃~80℃
Working voltage 2.8-5.5V
1 GND Power ground
2 VDD power supply positive (2.8-5.5V)
3 SCK clock line
4 SDA data cable
5 RES reset line
6 DC data/command
7 CS Chip Select

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Module parameters:
As electronics enthusiasts , you are not 'll find a 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply and tangled, is not the will to power is not enough to expand the number of interfaces and distress ? Such experience , I believe that people will engage in electronic design often encountered . To facilitate that we can find a safe high performance , ease of use , power regulator rich expansion interface module , shop designed in such a transfer 1.2V 1.5V 1.8V 2.5V 3.3V 5V power regulator module, which applies to single-chip design project requires 1.2V 1.5V 1.8V 2.5V 3.3V 5V power supply electronic equipment. Meanwhile , some of the electrons can be designed to facilitate the expansion of power .
1 Input : DC 4.5V--12V ( input voltage must be higher than the output voltage to 1V or more. )
2 Output : 1.2V 1.5V 1.8V 2.5V 3.3V 5V, ( load current must not exceed 800ma)
3 pairs of panel design, layout nice ;
4 specially designed two pin mounting holes , can be directly fixed on hole board for extended experiments ;
5 input and output using 2P single row pin for easy connection ;
6 PCB board size : 26*16mm
7 with power indicator light ( red )
8 tablet weight about : 1.6g

Description
Input voltage range: 4.75-24V

Output voltage range: 0.93V-18V (step-down operation mode, enter at least greater than the output 2V above)

Output Current: 2.5A peak output 4A continuous output!

Switch: With soft-off function! After microamps shutdown current low level!

Size: 45mm * 32mm * 1.6mm

Num: YS-TB

Technical Description:

Synchronous rectification technology! Maximum efficiency of 98% !

Efficiency Found: 12V turn 5V:

12V turn 5V efficiency = (5V * 1.001A) / (12V * 0.431) = 96.7%

Product Description
CNC shield V4 needs to work with Nano board. It can be used as driver expansion board for engraving machines and 3D printers. It has in total 3 channel slots for A4988 stepper motor driver modules (not included) for driving 3 channel of stepper motors. Each channel of stepper motor only needs 2 IO ports, which means 6 IO ports is sufficient to manage 3 stepper motors. This shield can make quick work for managing stepper motors in your project.
Specification:
1. 3 axis stepper motor driver
2. Compatible with micro-drive laser engraving machine, three-axis CNC engraving machine,.
3. 2A can be controlled within the two-phase four-wire stepper motor.
4. Released the digital IO interface, easy to connect to other modules, such as ENDSTOP.
5. Released the I2C interface, you can connect to the LCD I2C or other I2C module.
6. Power DC5V interface, 7.5-12V voltage input.
7. GRBL compatible
8. Worked with aduino nano.
1.Using A4988 module
2.Five different step mode
3.Adjust the maximum current output, so as to obtain a higher rate of step.
4.Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals
5.Can drive four A4988 stepper motor

Product Description
CNC shield V4 needs to work with Nano board. It can be used as driver expansion board for engraving machines and 3D printers. It has in total 3 channel slots for A4988 stepper motor driver modules (not included) for driving 3 channel of stepper motors. Each channel of stepper motor only needs 2 IO ports, which means 6 IO ports is sufficient to manage 3 stepper motors. This shield can make quick work for managing stepper motors in your project.
Specification:
1. 3 axis stepper motor driver
2. Compatible with micro-drive laser engraving machine, three-axis CNC engraving machine,.
3. 2A can be controlled within the two-phase four-wire stepper motor.
4. Released the digital IO interface, easy to connect to other modules, such as ENDSTOP.
5. Released the I2C interface, you can connect to the LCD I2C or other I2C module.
6. Power DC5V interface, 7.5-12V voltage input.
7. GRBL compatible
8. Worked with aduino nano.
1.Using A4988 module
2.Five different step mode
3.Adjust the maximum current output, so as to obtain a higher rate of step.
4.Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals
5.Can drive four A4988 stepper motor

Description
Model Name: Mini-360 (ultra small size DC-DC synchronous rectifier buck module）
Module Properties: non-isolated buck
Rectification: synchronous rectification
Input voltage: 4.75V-23V
Output voltage: 1.0V-17V
Output Current: lowering the value of 3A, long 1.8A
Conversion efficiency: 96% (maximum)
Switching Frequency: 340KHz
Output ripple: 30mV (no-load)
Load regulation: ±0.5%
Voltage regulation: ±2.5%
Working temperature: -40 Centigrade to 85 Centigrade
External dimensions: 17 * 11 * 3.8 (L * W * H) (mm)
Features: Use integrally molded power inductor and synchronous rectifier control chip, smaller and more efficient.

1N4007
1200V copper feet, overall length>45mm, wire diameter>0.5mm

Description
Support CAN V2.0 B , Communication rate up to 1Mb/S
Power supply: DC 5V , SPI Protocol Control
Work current: 5mA ,
Size: 4*2.8 cm , standby current: 1uA
Working temperature: -40 C - 85 C
120 Ohm terminal resistance, Impedance matching and guarantee the ability to drive

Features
As the pin resources controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic based project.

Specification:
I2C Address: 0x27
Supply voltage: 5V
the backlight and contrast is adjusted by potentiometer
Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
Compatible for 1602/2004 LCD

Description
1. Supply Voltage: 2.7v-5.5v @ 3mA current
2. Output: 2Vpp on 1.25V bias
3. Frequency Response: 20Hz - 20 KHz
4. Programmable Attack and Release Ratio
5. Automatic gain, selectable max from 40dB, 50dB or 60dB
6. Low Input-Referred Noise Density of 30nV/
7. Low THD: 0.04% (typ)

Product Introduction:
1.Input Voltage:0.9-5V;output voltage:5V
2.Maximum Output Current:480mA
3.Starting Up Voltage:0.8V;output current:7mA
4.Input Voltage:1-1.5V;output voltage 5V;current 40-100mA
5.Input Voltage:1.5-2V;output voltage 5V;current 100-150mA
6.Input Voltage:2-3V;output voltage 5V;current 150-380mA
7.Input Voltage:>3V;output voltage 5V;current 380-480mA
8.Operating Frequency:150KHz
9.Typical Conversion Efficiency:85%
10.Pin Space:2.54mm
11.Size:11*10.5*7.5mm
Notice:
1.Input voltage should be no more than rated voltage,or the module will be burnt
2.Input power should surpass output power,or output voltage will be less than rated voltage
3.Output load should be no more than rated load,or output voltage will be less than rated voltage

Description
1. On-board high-precision voltage detection chip and power supply regulator chip
2. Onboard 4-digit power indicator LED lights, displayed in 3 colors, red, yellow, yellow, and green represent 20% , 50% , 80% , and 100% power respectively
3. Reserve a battery detection interface and two installation positioning holes
4. PCB size: 22.2(mm)x17.2(mm)

Features:
1. bluetooth V4.2 version, unterstützung Bluetooth automatische verbindung technologie, unterstützung WAV/WMA/FLAC/APE/MP3 verlustfreie decodierung, stereo dual channel 2.nach die modul ist powered auf, die handy sucht für die Bluetooth name MH-M18/MH-M28/MH-M38, und kann musik spielen nach dem anschluss Bluetooth. 3.modul blau anzeige licht: Wenn die Bluetooth ist nicht verbunden, die anzeige licht blinkt schnell; Wenn die bluetooth-verbindung ist auf, die anzeige licht ist immer auf; Die folgenden ist eine einführung zu jeder version: MH-M18: PCB größe: 23*16*2,5mm (länge, breite und höhe) Pin pitch: 2,54mm (kann direkt angebracht oder gelötet)
Precise incisions and interfaces ensure perfect suitability for mounting position. Easy installation.
Made of high quality materials, corrosion-resistant, wear-resistant, durable and long life time.
Professional chip sets provide excellent performance in the system.
Low power consumption, support Bluetooth 4.2 transmission, dual channel stereo lossless playback. After module connect with Bluetooth, it can quickly realize Bluetooth wireless transmission, very convenient to use.
The Bluetooth connection distance can be up to 20 meters in open space. It is widely used in all kinds of Bluetooth audio receiving and all kinds of DIY audio modification, etc.
Specification:
Material: ABS
Color: As picture shown
Working Voltage: 5V/ 3.7-4.2V
Connection Working Status: 20mA
Transmission Distance: 20 meters (in open space or low interference conditions)
Working Temperature: -40℃-85℃
Size: Approx. 2.3x1.7x0.2 cm/ 0.91x0.67x0.08 inch

Description
Product name: 3 strings of 12.6V 40A lithium battery protection board
Charging voltage: DC 12.6V~13.6V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Balanced version Product size: 41*61*4mm
Enhanced version Product size: 41*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: Successful drilling requires 3 10C-20C power batteries, or 6 5C-10C power batteries (recommended power battery models: sony vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, using 3 square millimeters of copper Wire or more (nickel sheet cannot be used)
Note 2: Connect 0V, 4.2V, 8.4V, 12.6V strictly according to the figure. Do not touch any components on the board when soldering wires. Don't short-circuit intentionally.
Note 3: When the battery is welded or charged for the first time, as long as the single battery exceeds 4.2V, the "430" resistor will heat and discharge (discharge to about 4.19V and stop heating). If the "430" resistor is heating up severely, please check whether it is connected to the wrong wire.
Product name: 4 series 14.8V 16.8V 40A lithium battery protection board
Charging voltage: DC 16.8V~17V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Scale version Product size: 45*60*4mm
Enhanced version Product size: 44*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: The electric drill needs 3 15C-20C power batteries, or 6 10C-15C power batteries (normal 18650 cannot start the electric drill!!!).

Note 2: Wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, do not intentionally short-circuit.


Note 3: When using a brushed motor load, try to connect non-polar capacitors (withstand voltage above 25V, capacity 10uF-100uF) between the positive and negative poles of the motor to prevent reverse peaks of the motor. Disconnect the MOS tube.

Note 4: 4 sets of batteries are used in series. Please ensure the voltage of each set of batteries. If they are not the same, please fill up each set of batteries separately and then use them in series. In the discharge test, the battery pack with a faster voltage drop is an inferior battery.
Product name: 3S lithium battery protection board 60A enhanced version
(1) Product description: This product is used to charge and discharge three groups of lithium batteries in series, and each group can connect multiple lithium batteries in parallel. it can
Withstand continuous charging current 20A, continuous discharging current 40A, and instantaneous current below 80A. used
During this process, the heat dissipation conditions should be good. If the heat dissipation condition is not good, please reduce the current usage and do not let the board
The child has a noticeable sensation of heat. Overcharge protection, overdischarge protection, and overcurrent protection during charging and discharging
Protection, short circuit protection. This product can be used for electric drills, sprayers, LED lights, and low-power reversing.
Charge and discharge batteries for products such as transformers.
(2) Product parameters:
◆ Product model: HW-552;
◆ Size: 41*60*1mm;
Charging voltage: 12.6V-13V;
◆ Maximum working current: 60A (good heat dissipation conditions);
◆ Continuous charging current (upper limit): 20A;
◆ Continuous discharge current (upper limit): 40A;
◆ Overcurrent protection: 125A;.
◆ Overcharge detection: 12.8V (3 sets of batteries);
◆ Overcharge release: 12.3V (3 sets of batteries);
◆ Over-discharge detection: 2.4V (1 battery);
◆ Over-discharge release: 3.0V (1 battery);
◆ Short circuit protection: Yes;
◆ Working temperature: -40-- 85C;
◆ Storage conditions: -40-- 125C.

Description
Product name: 3 strings of 12.6V 40A lithium battery protection board
Charging voltage: DC 12.6V~13.6V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Balanced version Product size: 41*61*4mm
Enhanced version Product size: 41*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: Successful drilling requires 3 10C-20C power batteries, or 6 5C-10C power batteries (recommended power battery models: sony vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, using 3 square millimeters of copper Wire or more (nickel sheet cannot be used)
Note 2: Connect 0V, 4.2V, 8.4V, 12.6V strictly according to the figure. Do not touch any components on the board when soldering wires. Don't short-circuit intentionally.
Note 3: When the battery is welded or charged for the first time, as long as the single battery exceeds 4.2V, the "430" resistor will heat and discharge (discharge to about 4.19V and stop heating). If the "430" resistor is heating up severely, please check whether it is connected to the wrong wire.
Product name: 4 series 14.8V 16.8V 40A lithium battery protection board
Charging voltage: DC 16.8V~17V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Scale version Product size: 45*60*4mm
Enhanced version Product size: 44*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: The electric drill needs 3 15C-20C power batteries, or 6 10C-15C power batteries (normal 18650 cannot start the electric drill!!!).

Note 2: Wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, do not intentionally short-circuit.


Note 3: When using a brushed motor load, try to connect non-polar capacitors (withstand voltage above 25V, capacity 10uF-100uF) between the positive and negative poles of the motor to prevent reverse peaks of the motor. Disconnect the MOS tube.

Note 4: 4 sets of batteries are used in series. Please ensure the voltage of each set of batteries. If they are not the same, please fill up each set of batteries separately and then use them in series. In the discharge test, the battery pack with a faster voltage drop is an inferior battery.
Product name: 3S lithium battery protection board 60A enhanced version
(1) Product description: This product is used to charge and discharge three groups of lithium batteries in series, and each group can connect multiple lithium batteries in parallel. it can
Withstand continuous charging current 20A, continuous discharging current 40A, and instantaneous current below 80A. used
During this process, the heat dissipation conditions should be good. If the heat dissipation condition is not good, please reduce the current usage and do not let the board
The child has a noticeable sensation of heat. Overcharge protection, overdischarge protection, and overcurrent protection during charging and discharging
Protection, short circuit protection. This product can be used for electric drills, sprayers, LED lights, and low-power reversing.
Charge and discharge batteries for products such as transformers.
(2) Product parameters:
◆ Product model: HW-552;
◆ Size: 41*60*1mm;
Charging voltage: 12.6V-13V;
◆ Maximum working current: 60A (good heat dissipation conditions);
◆ Continuous charging current (upper limit): 20A;
◆ Continuous discharge current (upper limit): 40A;
◆ Overcurrent protection: 125A;.
◆ Overcharge detection: 12.8V (3 sets of batteries);
◆ Overcharge release: 12.3V (3 sets of batteries);
◆ Over-discharge detection: 2.4V (1 battery);
◆ Over-discharge release: 3.0V (1 battery);
◆ Short circuit protection: Yes;
◆ Working temperature: -40-- 85C;
◆ Storage conditions: -40-- 125C.

Description
Product name: 3 strings of 12.6V 40A lithium battery protection board
Charging voltage: DC 12.6V~13.6V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Balanced version Product size: 41*61*4mm
Enhanced version Product size: 41*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: Successful drilling requires 3 10C-20C power batteries, or 6 5C-10C power batteries (recommended power battery models: sony vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, using 3 square millimeters of copper Wire or more (nickel sheet cannot be used)
Note 2: Connect 0V, 4.2V, 8.4V, 12.6V strictly according to the figure. Do not touch any components on the board when soldering wires. Don't short-circuit intentionally.
Note 3: When the battery is welded or charged for the first time, as long as the single battery exceeds 4.2V, the "430" resistor will heat and discharge (discharge to about 4.19V and stop heating). If the "430" resistor is heating up severely, please check whether it is connected to the wrong wire.
Product name: 4 series 14.8V 16.8V 40A lithium battery protection board
Charging voltage: DC 16.8V~17V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Scale version Product size: 45*60*4mm
Enhanced version Product size: 44*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: The electric drill needs 3 15C-20C power batteries, or 6 10C-15C power batteries (normal 18650 cannot start the electric drill!!!).

Note 2: Wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, do not intentionally short-circuit.


Note 3: When using a brushed motor load, try to connect non-polar capacitors (withstand voltage above 25V, capacity 10uF-100uF) between the positive and negative poles of the motor to prevent reverse peaks of the motor. Disconnect the MOS tube.

Note 4: 4 sets of batteries are used in series. Please ensure the voltage of each set of batteries. If they are not the same, please fill up each set of batteries separately and then use them in series. In the discharge test, the battery pack with a faster voltage drop is an inferior battery.
Product name: 3S lithium battery protection board 60A enhanced version
(1) Product description: This product is used to charge and discharge three groups of lithium batteries in series, and each group can connect multiple lithium batteries in parallel. it can
Withstand continuous charging current 20A, continuous discharging current 40A, and instantaneous current below 80A. used
During this process, the heat dissipation conditions should be good. If the heat dissipation condition is not good, please reduce the current usage and do not let the board
The child has a noticeable sensation of heat. Overcharge protection, overdischarge protection, and overcurrent protection during charging and discharging
Protection, short circuit protection. This product can be used for electric drills, sprayers, LED lights, and low-power reversing.
Charge and discharge batteries for products such as transformers.
(2) Product parameters:
◆ Product model: HW-552;
◆ Size: 41*60*1mm;
Charging voltage: 12.6V-13V;
◆ Maximum working current: 60A (good heat dissipation conditions);
◆ Continuous charging current (upper limit): 20A;
◆ Continuous discharge current (upper limit): 40A;
◆ Overcurrent protection: 125A;.
◆ Overcharge detection: 12.8V (3 sets of batteries);
◆ Overcharge release: 12.3V (3 sets of batteries);
◆ Over-discharge detection: 2.4V (1 battery);
◆ Over-discharge release: 3.0V (1 battery);
◆ Short circuit protection: Yes;
◆ Working temperature: -40-- 85C;
◆ Storage conditions: -40-- 125C.

Description
Product name: 3 strings of 12.6V 40A lithium battery protection board
Charging voltage: DC 12.6V~13.6V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Balanced version Product size: 41*61*4mm
Enhanced version Product size: 41*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: Successful drilling requires 3 10C-20C power batteries, or 6 5C-10C power batteries (recommended power battery models: sony vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, using 3 square millimeters of copper Wire or more (nickel sheet cannot be used)
Note 2: Connect 0V, 4.2V, 8.4V, 12.6V strictly according to the figure. Do not touch any components on the board when soldering wires. Don't short-circuit intentionally.
Note 3: When the battery is welded or charged for the first time, as long as the single battery exceeds 4.2V, the "430" resistor will heat and discharge (discharge to about 4.19V and stop heating). If the "430" resistor is heating up severely, please check whether it is connected to the wrong wire.
Product name: 4 series 14.8V 16.8V 40A lithium battery protection board
Charging voltage: DC 16.8V~17V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Scale version Product size: 45*60*4mm
Enhanced version Product size: 44*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: The electric drill needs 3 15C-20C power batteries, or 6 10C-15C power batteries (normal 18650 cannot start the electric drill!!!).

Note 2: Wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, do not intentionally short-circuit.


Note 3: When using a brushed motor load, try to connect non-polar capacitors (withstand voltage above 25V, capacity 10uF-100uF) between the positive and negative poles of the motor to prevent reverse peaks of the motor. Disconnect the MOS tube.

Note 4: 4 sets of batteries are used in series. Please ensure the voltage of each set of batteries. If they are not the same, please fill up each set of batteries separately and then use them in series. In the discharge test, the battery pack with a faster voltage drop is an inferior battery.
Product name: 3S lithium battery protection board 60A enhanced version
(1) Product description: This product is used to charge and discharge three groups of lithium batteries in series, and each group can connect multiple lithium batteries in parallel. it can
Withstand continuous charging current 20A, continuous discharging current 40A, and instantaneous current below 80A. used
During this process, the heat dissipation conditions should be good. If the heat dissipation condition is not good, please reduce the current usage and do not let the board
The child has a noticeable sensation of heat. Overcharge protection, overdischarge protection, and overcurrent protection during charging and discharging
Protection, short circuit protection. This product can be used for electric drills, sprayers, LED lights, and low-power reversing.
Charge and discharge batteries for products such as transformers.
(2) Product parameters:
◆ Product model: HW-552;
◆ Size: 41*60*1mm;
Charging voltage: 12.6V-13V;
◆ Maximum working current: 60A (good heat dissipation conditions);
◆ Continuous charging current (upper limit): 20A;
◆ Continuous discharge current (upper limit): 40A;
◆ Overcurrent protection: 125A;.
◆ Overcharge detection: 12.8V (3 sets of batteries);
◆ Overcharge release: 12.3V (3 sets of batteries);
◆ Over-discharge detection: 2.4V (1 battery);
◆ Over-discharge release: 3.0V (1 battery);
◆ Short circuit protection: Yes;
◆ Working temperature: -40-- 85C;
◆ Storage conditions: -40-- 125C.

Description
Product name: 3 strings of 12.6V 40A lithium battery protection board
Charging voltage: DC 12.6V~13.6V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Balanced version Product size: 41*61*4mm
Enhanced version Product size: 41*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: Successful drilling requires 3 10C-20C power batteries, or 6 5C-10C power batteries (recommended power battery models: sony vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, using 3 square millimeters of copper Wire or more (nickel sheet cannot be used)
Note 2: Connect 0V, 4.2V, 8.4V, 12.6V strictly according to the figure. Do not touch any components on the board when soldering wires. Don't short-circuit intentionally.
Note 3: When the battery is welded or charged for the first time, as long as the single battery exceeds 4.2V, the "430" resistor will heat and discharge (discharge to about 4.19V and stop heating). If the "430" resistor is heating up severely, please check whether it is connected to the wrong wire.
Product name: 4 series 14.8V 16.8V 40A lithium battery protection board
Charging voltage: DC 16.8V~17V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Scale version Product size: 45*60*4mm
Enhanced version Product size: 44*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: The electric drill needs 3 15C-20C power batteries, or 6 10C-15C power batteries (normal 18650 cannot start the electric drill!!!).

Note 2: Wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, do not intentionally short-circuit.


Note 3: When using a brushed motor load, try to connect non-polar capacitors (withstand voltage above 25V, capacity 10uF-100uF) between the positive and negative poles of the motor to prevent reverse peaks of the motor. Disconnect the MOS tube.

Note 4: 4 sets of batteries are used in series. Please ensure the voltage of each set of batteries. If they are not the same, please fill up each set of batteries separately and then use them in series. In the discharge test, the battery pack with a faster voltage drop is an inferior battery.
Product name: 3S lithium battery protection board 60A enhanced version
(1) Product description: This product is used to charge and discharge three groups of lithium batteries in series, and each group can connect multiple lithium batteries in parallel. it can
Withstand continuous charging current 20A, continuous discharging current 40A, and instantaneous current below 80A. used
During this process, the heat dissipation conditions should be good. If the heat dissipation condition is not good, please reduce the current usage and do not let the board
The child has a noticeable sensation of heat. Overcharge protection, overdischarge protection, and overcurrent protection during charging and discharging
Protection, short circuit protection. This product can be used for electric drills, sprayers, LED lights, and low-power reversing.
Charge and discharge batteries for products such as transformers.
(2) Product parameters:
◆ Product model: HW-552;
◆ Size: 41*60*1mm;
Charging voltage: 12.6V-13V;
◆ Maximum working current: 60A (good heat dissipation conditions);
◆ Continuous charging current (upper limit): 20A;
◆ Continuous discharge current (upper limit): 40A;
◆ Overcurrent protection: 125A;.
◆ Overcharge detection: 12.8V (3 sets of batteries);
◆ Overcharge release: 12.3V (3 sets of batteries);
◆ Over-discharge detection: 2.4V (1 battery);
◆ Over-discharge release: 3.0V (1 battery);
◆ Short circuit protection: Yes;
◆ Working temperature: -40-- 85C;
◆ Storage conditions: -40-- 125C.

Description
Product name: 3 strings of 12.6V 40A lithium battery protection board
Charging voltage: DC 12.6V~13.6V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Balanced version Product size: 41*61*4mm
Enhanced version Product size: 41*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: Successful drilling requires 3 10C-20C power batteries, or 6 5C-10C power batteries (recommended power battery models: sony vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, using 3 square millimeters of copper Wire or more (nickel sheet cannot be used)
Note 2: Connect 0V, 4.2V, 8.4V, 12.6V strictly according to the figure. Do not touch any components on the board when soldering wires. Don't short-circuit intentionally.
Note 3: When the battery is welded or charged for the first time, as long as the single battery exceeds 4.2V, the "430" resistor will heat and discharge (discharge to about 4.19V and stop heating). If the "430" resistor is heating up severely, please check whether it is connected to the wrong wire.
Product name: 4 series 14.8V 16.8V 40A lithium battery protection board
Charging voltage: DC 16.8V~17V
Continuous discharge current: Maximum 40A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current: up to 20A
Scale version Product size: 45*60*4mm
Enhanced version Product size: 44*55*4mm
Applicable options: suitable for a 4.2V lithium battery with a nominal voltage of 3.7V and a full charge
(Including 18650, 26650, polymer lithium battery), can be punched below 170W

Note 1: The electric drill needs 3 15C-20C power batteries, or 6 10C-15C power batteries (normal 18650 cannot start the electric drill!!!).

Note 2: Wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, do not intentionally short-circuit.


Note 3: When using a brushed motor load, try to connect non-polar capacitors (withstand voltage above 25V, capacity 10uF-100uF) between the positive and negative poles of the motor to prevent reverse peaks of the motor. Disconnect the MOS tube.

Note 4: 4 sets of batteries are used in series. Please ensure the voltage of each set of batteries. If they are not the same, please fill up each set of batteries separately and then use them in series. In the discharge test, the battery pack with a faster voltage drop is an inferior battery.
Product name: 3S lithium battery protection board 60A enhanced version
(1) Product description: This product is used to charge and discharge three groups of lithium batteries in series, and each group can connect multiple lithium batteries in parallel. it can
Withstand continuous charging current 20A, continuous discharging current 40A, and instantaneous current below 80A. used
During this process, the heat dissipation conditions should be good. If the heat dissipation condition is not good, please reduce the current usage and do not let the board
The child has a noticeable sensation of heat. Overcharge protection, overdischarge protection, and overcurrent protection during charging and discharging
Protection, short circuit protection. This product can be used for electric drills, sprayers, LED lights, and low-power reversing.
Charge and discharge batteries for products such as transformers.
(2) Product parameters:
◆ Product model: HW-552;
◆ Size: 41*60*1mm;
Charging voltage: 12.6V-13V;
◆ Maximum working current: 60A (good heat dissipation conditions);
◆ Continuous charging current (upper limit): 20A;
◆ Continuous discharge current (upper limit): 40A;
◆ Overcurrent protection: 125A;.
◆ Overcharge detection: 12.8V (3 sets of batteries);
◆ Overcharge release: 12.3V (3 sets of batteries);
◆ Over-discharge detection: 2.4V (1 battery);
◆ Over-discharge release: 3.0V (1 battery);
◆ Short circuit protection: Yes;
◆ Working temperature: -40-- 85C;
◆ Storage conditions: -40-- 125C.

Product Description
This is a small vibration motor suitable as a non-audible indicator. When the input is high, the motor vibrates, just like your silent mode phone.
Feature:
- Rated voltage: 5.0VDC
- Operating voltage: 3.0 - 5.3VDC
- Rated speed: 9000 rpm minimum
- Rated current: up to 60 mA
- Starting current: up to 90 mA
- Starting voltage: DC3.7V
- Insulation resistance: 10Mohm
- Compatibility: Compatible with UNO R3/ Mega2560
- Great for DIY projects
Technical Specifications
size
21*23mm
Fixed hole
3mm
Pitch
15mm
Voltage
5V
port
Digital quantity
motor
10mm diameter, 2.7mm thickness, flat motor
drive
MOS tube high level trigger, low level cutoff
platform
Ard-uino, MCU
Product Features:
High-quality mobile phone vibration motor, the vibration effect is obvious
Mos amplification driver, can directly pass Ard-uino Digital port control
The vibration intensity of the motor can be controlled by PWM
This module can easily convert electrical signals to mechanical vibration.
Suitable for the production of vibration-sensitive interactive products, wearable smart device vibration reminders, etc.

Describe:
USBtinyISP is specially designed for AVR, ISP download based on USB connector.
Officially supported by AR IDE and compatible usbtinyisp, we can burn the AR bootloader onto the chip and actually program any Atmel AVR microcontroller through the powerful AVR ISP programmer.
The micro ISP programmer can provide 5V power supply voltage for the board being programmed. If you want to supply power to the circuit board through ISP, you must close the SJVCC jumper on the circuit board.
Using this programmer, you can upload sketches and burn Bootloader on any AVR-based circuit board, including AR. By using an external programmer to upload the sketch, you can delete the bootloader and use extra space for the sketch. For AR ISP can also be used to burn AR bootloader, so if the bootloader is accidentally damaged, you can restore the chip. When you use the new ATmega microcontroller in AR, you also need to burn the bootloader, and you want to use the bootloader to upload the sketch via a USB serial connection. Support ATTiny45 and ATTiny85 chips for AR programming, etc.

specification:
Power supply voltage: 5 V
Microcontroller: ATtiny44 (data sheet)
Connect with computer: micro USB
Connection with target board: ICSP
Board size: 23x14mm (approximately)
how to use:
Connect the AR ISP to the ICSP header of the AR board. Make sure to match the orientation of the plug by looking at the white dots on the corners of the connector
Open the AR IDE, select the hardware name downloaded in the "board", select "USBtinyISP" under the "Burn Bootloader" menu, and then bootlaoder starts downloading and completes in 10 seconds (atmega328)

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer

10pcs 3296W 3296 50 100 200 500 ohm 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M ohm 103 100R 200R 500R Trimpot Trimmer Potentiometer