Szerszám alkatrészek és tartozékok

 
Description:
Product name: Damaged Nut Bolt Remover
Color: Black
Standard: Metric
Type of Thread: Reverse spiral cut, tapered
Model: # 1- # 10
Remove No. : #1/2/3/4/5/6/7/8/9/10
Inside Size(Fit for removing Hex Size): 9/10/11/12/13/14/15/16/17/19mm
Outside Hex Size: 16/16/19/19/19/22/22/25/25/27mm
Size of box: Approx. 17.2x7.9x4.2cm/6.77"x3.11"x1.65"

 
Description:
Product name: Damaged Nut Bolt Remover
Color: Black
Standard: Metric
Type of Thread: Reverse spiral cut, tapered
Model: # 1- # 10
Remove No. : #1/2/3/4/5/6/7/8/9/10
Inside Size(Fit for removing Hex Size): 9/10/11/12/13/14/15/16/17/19mm
Outside Hex Size: 16/16/19/19/19/22/22/25/25/27mm
Size of box: Approx. 17.2x7.9x4.2cm/6.77"x3.11"x1.65"

Operation steps:
1. Install and adjust the bracket and screws, Adjust the bottle to the length you want.
2.  Rotate the bottle and keep it moving, mkae sure the cutting line is connected end to end.
3. Place 2 suitable rubber rings on both side of the score line.
4. Pour very hot water over it for about 20 seconds, rotating to completely heat the score line.
5. Then switch to cold water (ice water), pouring it over the score line as you rotate the bottle for about 20 seconds.
6. The edge of the remaining section of the bottle might be rough and jagged, so use the sandpaper to smooth it out.

Specification:
Name: Multifunctional ratchet type labor saving terminal crimping pliers
Color: yellow
Function: suitable for a variety of terminal crimping
Wire stripper stripping range: 0.2-6mm2 ( 24-10AWG)
Crimping pliers crimping range:
JX-1601-08(0.14-1.5mm2, 26-16WAG)----This jaw is mounted on the pliers
JX-1601-2546 (2.5-4.0-6.mm2, 14-10AWG),
JX-1601-01(0.25-2.5mm2, 24-14AWG),
JX-1601-06(0.25-6.0mm2, 24-10AWG),

Specification:
Name: Multifunctional ratchet type labor saving terminal crimping pliers
Color: yellow
Function: suitable for a variety of terminal crimping
Wire stripper stripping range: 0.2-6mm2 ( 24-10AWG)
Crimping pliers crimping range:
JX-1601-08(0.14-1.5mm2, 26-16WAG)----This jaw is mounted on the pliers
JX-1601-2546 (2.5-4.0-6.mm2, 14-10AWG),
JX-1601-01(0.25-2.5mm2, 24-14AWG),
JX-1601-06(0.25-6.0mm2, 24-10AWG),

Specification:
Name: Multifunctional ratchet type labor saving terminal crimping pliers
Color: yellow
Function: suitable for a variety of terminal crimping
Wire stripper stripping range: 0.2-6mm2 ( 24-10AWG)
Crimping pliers crimping range:
JX-1601-08(0.14-1.5mm2, 26-16WAG)----This jaw is mounted on the pliers
JX-1601-2546 (2.5-4.0-6.mm2, 14-10AWG),
JX-1601-01(0.25-2.5mm2, 24-14AWG),
JX-1601-06(0.25-6.0mm2, 24-10AWG),

Specification:
Name: Multifunctional ratchet type labor saving terminal crimping pliers
Color: yellow
Function: suitable for a variety of terminal crimping
Wire stripper stripping range: 0.2-6mm2 ( 24-10AWG)
Crimping pliers crimping range:
JX-1601-08(0.14-1.5mm2, 26-16WAG)----This jaw is mounted on the pliers
JX-1601-2546 (2.5-4.0-6.mm2, 14-10AWG),
JX-1601-01(0.25-2.5mm2, 24-14AWG),
JX-1601-06(0.25-6.0mm2, 24-10AWG),

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

 
  Crimping Pliers Set SN-48BS 8 jaw Kit for 2.8 4.8 6.3 VH2.54 3.96 2510/Tube/Insulation Terminals Electrical Clamp Min Tools
Description:
HS-03BC HAND CRIMPING TOOLS(9")

Specification:
45 In 1 Screwdriver Set：
Phillips: PH000, PH00, PH0, PH1
Socket: 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0
Hex: 0.9, 1.5, 2.0, 4.5, 5.0, 6.0
Torx: T2, T4, T5, T6, T7, T8
Slotted: 1.0, 2.0, 4.0
G-Type: 3.8, 4.5
5-Point: 0.8, 1.2
Spanner: U2.6
Triangle: 2.3
Y-Type: Y0.6
MID: 1.5
1*PH1.3 Screwdriver
1*5-Point 0.8 Screwdriver
1*Slotted 2.0 Screwdriver
1*Y-Type Y0.6 Screwdriver
1*Torx T2 Screwdriver
1*Extension bar
1*Handle
1*Tweezer
1*Suction cup
2*Opening picks
38 In 1 Screwdriver Set：
Socket: M5 M6 M7 M8 M9 M10 M11 M12 M13 M14
PH0, PH1, PH2
Straight: 3.0, 5.0, 6.0
Torx: T6, T10, T15, T25, T30
Hexagon: H3, H4, H5, H6
Pz2, Pz3
"Y" shape: 2.0 and 3.0
"U" form: 4.0 and 6.0
Triangle: 2.3
1*Spring extension bar
1*Shaft extension
1*Sleeve joystick
1*Hook drive
1*Handle
1*Socket Wrench
25 In 1 Screwdriver Set:
Holster Open Size: approx. 20 x 10.3cm /7.8 x 4.0 inch
Holster Color: Black
Tool Color: Silver
Material: Steel
Five-star screw driver: 0.8 1.2
Trox screw driver:T2 T3 T4 T5 T6 T7 T8 T9 T10 T15
Triangle driver:2.3
Y screw driver: 2.0
Cross screw driver:1.0 1.2 2.0 3.0
Flat screw driver: 1.0 1.5 2.0 3.0
Point screw driver:0.8
Net Weight: 125g
Note:
1. Please allow 1-3mm error due to manual measurement. please make sure you do not mind before you bid.
2. Due to lighting effects, monitor's brightness contrast settings etc, there could be some slight differences in the color tone of the pictures and the actual item!
3. About this product, in view of the production batch problem at different stages of the factory, may be different from the brand on the label, but please be assured that the quality of the product is the same. This is what we can guarantee and promise. If you mind this, please buy it carefully. Thank you!

Specification:
45 In 1 Screwdriver Set：
Phillips: PH000, PH00, PH0, PH1
Socket: 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0
Hex: 0.9, 1.5, 2.0, 4.5, 5.0, 6.0
Torx: T2, T4, T5, T6, T7, T8
Slotted: 1.0, 2.0, 4.0
G-Type: 3.8, 4.5
5-Point: 0.8, 1.2
Spanner: U2.6
Triangle: 2.3
Y-Type: Y0.6
MID: 1.5
1*PH1.3 Screwdriver
1*5-Point 0.8 Screwdriver
1*Slotted 2.0 Screwdriver
1*Y-Type Y0.6 Screwdriver
1*Torx T2 Screwdriver
1*Extension bar
1*Handle
1*Tweezer
1*Suction cup
2*Opening picks
38 In 1 Screwdriver Set：
Socket: M5 M6 M7 M8 M9 M10 M11 M12 M13 M14
PH0, PH1, PH2
Straight: 3.0, 5.0, 6.0
Torx: T6, T10, T15, T25, T30
Hexagon: H3, H4, H5, H6
Pz2, Pz3
"Y" shape: 2.0 and 3.0
"U" form: 4.0 and 6.0
Triangle: 2.3
1*Spring extension bar
1*Shaft extension
1*Sleeve joystick
1*Hook drive
1*Handle
1*Socket Wrench
25 In 1 Screwdriver Set:
Holster Open Size: approx. 20 x 10.3cm /7.8 x 4.0 inch
Holster Color: Black
Tool Color: Silver
Material: Steel
Five-star screw driver: 0.8 1.2
Trox screw driver:T2 T3 T4 T5 T6 T7 T8 T9 T10 T15
Triangle driver:2.3
Y screw driver: 2.0
Cross screw driver:1.0 1.2 2.0 3.0
Flat screw driver: 1.0 1.5 2.0 3.0
Point screw driver:0.8
Net Weight: 125g
Note:
1. Please allow 1-3mm error due to manual measurement. please make sure you do not mind before you bid.
2. Due to lighting effects, monitor's brightness contrast settings etc, there could be some slight differences in the color tone of the pictures and the actual item!
3. About this product, in view of the production batch problem at different stages of the factory, may be different from the brand on the label, but please be assured that the quality of the product is the same. This is what we can guarantee and promise. If you mind this, please buy it carefully. Thank you!

Specification:
45 In 1 Screwdriver Set：
Phillips: PH000, PH00, PH0, PH1
Socket: 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0
Hex: 0.9, 1.5, 2.0, 4.5, 5.0, 6.0
Torx: T2, T4, T5, T6, T7, T8
Slotted: 1.0, 2.0, 4.0
G-Type: 3.8, 4.5
5-Point: 0.8, 1.2
Spanner: U2.6
Triangle: 2.3
Y-Type: Y0.6
MID: 1.5
1*PH1.3 Screwdriver
1*5-Point 0.8 Screwdriver
1*Slotted 2.0 Screwdriver
1*Y-Type Y0.6 Screwdriver
1*Torx T2 Screwdriver
1*Extension bar
1*Handle
1*Tweezer
1*Suction cup
2*Opening picks
38 In 1 Screwdriver Set：
Socket: M5 M6 M7 M8 M9 M10 M11 M12 M13 M14
PH0, PH1, PH2
Straight: 3.0, 5.0, 6.0
Torx: T6, T10, T15, T25, T30
Hexagon: H3, H4, H5, H6
Pz2, Pz3
"Y" shape: 2.0 and 3.0
"U" form: 4.0 and 6.0
Triangle: 2.3
1*Spring extension bar
1*Shaft extension
1*Sleeve joystick
1*Hook drive
1*Handle
1*Socket Wrench
25 In 1 Screwdriver Set:
Holster Open Size: approx. 20 x 10.3cm /7.8 x 4.0 inch
Holster Color: Black
Tool Color: Silver
Material: Steel
Five-star screw driver: 0.8 1.2
Trox screw driver:T2 T3 T4 T5 T6 T7 T8 T9 T10 T15
Triangle driver:2.3
Y screw driver: 2.0
Cross screw driver:1.0 1.2 2.0 3.0
Flat screw driver: 1.0 1.5 2.0 3.0
Point screw driver:0.8
Net Weight: 125g
Note:
1. Please allow 1-3mm error due to manual measurement. please make sure you do not mind before you bid.
2. Due to lighting effects, monitor's brightness contrast settings etc, there could be some slight differences in the color tone of the pictures and the actual item!
3. About this product, in view of the production batch problem at different stages of the factory, may be different from the brand on the label, but please be assured that the quality of the product is the same. This is what we can guarantee and promise. If you mind this, please buy it carefully. Thank you!

Specification:
Package Contents:10 Pieces
Handle Material:TPR
Type:Slotted,Phillips,Electrician Pen
Head Treatment:Nickel-Plated
Overall Color:Red,Yellow,Black
Application:Home,Renovation Team

Specification:
Package Contents:10 Pieces
Handle Material:TPR
Type:Slotted,Phillips,Electrician Pen
Head Treatment:Nickel-Plated
Overall Color:Red,Yellow,Black
Application:Home,Renovation Team

Specification:
Type: Crimping pliers
Material: Carbon Steel
Crimping range: 2.5/4/6MM2
Function: Multi-function Crimping pliers
Application: For MC4 Solar photovoltaic connector crimpingpliers

Specification:
Type: Crimping pliers
Material: Carbon Steel
Crimping range: 2.5/4/6MM2
Function: Multi-function Crimping pliers
Application: For MC4 Solar photovoltaic connector crimpingpliers

14-30 / 30-60mm Universal Key Pipe Wrench Open End Spanner Set High-carbon Steel Snap N Grip Tool Plumber Multi Hand Tool

14-30 / 30-60mm Universal Key Pipe Wrench Open End Spanner Set High-carbon Steel Snap N Grip Tool Plumber Multi Hand Tool

14-30 / 30-60mm Universal Key Pipe Wrench Open End Spanner Set High-carbon Steel Snap N Grip Tool Plumber Multi Hand Tool

Specification:
Product Material: HSS Co
Shank: (approx.)
1) 4-32: 10 mm/0.39 in (triangular cylinder shank )
2) 4-20: 8 mm/0.31 in (triangular cylinder shank)
3) 4-12: 6 mm/0.24 in (triangular cylinder shank)
Size: (approx.)
4-12 mm (4mm, 6mm, 8mm, 10mm, 12mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in ) 5 Steps
4-20 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in) 9 Steps
4-32 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm, 26mm, 28mm, 30mm, 32mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in, 0.87in, 0.94in, 1.02in,1.10in,1.18in,1.26in ) 15 Steps
Main Function Of The Product: M35 cobalt step drill (HSS Co) is a high hardness step drill bit that is mainly applied for drilling high hardness steel, such as, the stainless steel plane and hardened steel.
The M35 step drill bit can be utilized to drill holes in the stainless steel plane.
The following points that you need pay attention to:
1. You can use the hand drill and bench drill to drill holes in the stainless steel plane. Use the hand drill for the board whose thickness is within 1 mm/0.04 in, while use the bench drill for the boards whose thickness is about 2-3 mm/0.08-0.12 in;
2. The drilling sped can't be too fast on the stainless steel plate. Hundreds rpm is enough.
3. Please add the water or cutting fluid to cool down during the processing so as to extend the service life of the drill bits.

Specification:
Product Material: HSS Co
Shank: (approx.)
1) 4-32: 10 mm/0.39 in (triangular cylinder shank )
2) 4-20: 8 mm/0.31 in (triangular cylinder shank)
3) 4-12: 6 mm/0.24 in (triangular cylinder shank)
Size: (approx.)
4-12 mm (4mm, 6mm, 8mm, 10mm, 12mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in ) 5 Steps
4-20 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in) 9 Steps
4-32 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm, 26mm, 28mm, 30mm, 32mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in, 0.87in, 0.94in, 1.02in,1.10in,1.18in,1.26in ) 15 Steps
Main Function Of The Product: M35 cobalt step drill (HSS Co) is a high hardness step drill bit that is mainly applied for drilling high hardness steel, such as, the stainless steel plane and hardened steel.
The M35 step drill bit can be utilized to drill holes in the stainless steel plane.
The following points that you need pay attention to:
1. You can use the hand drill and bench drill to drill holes in the stainless steel plane. Use the hand drill for the board whose thickness is within 1 mm/0.04 in, while use the bench drill for the boards whose thickness is about 2-3 mm/0.08-0.12 in;
2. The drilling sped can't be too fast on the stainless steel plate. Hundreds rpm is enough.
3. Please add the water or cutting fluid to cool down during the processing so as to extend the service life of the drill bits.

Specification:
Product Material: HSS Co
Shank: (approx.)
1) 4-32: 10 mm/0.39 in (triangular cylinder shank )
2) 4-20: 8 mm/0.31 in (triangular cylinder shank)
3) 4-12: 6 mm/0.24 in (triangular cylinder shank)
Size: (approx.)
4-12 mm (4mm, 6mm, 8mm, 10mm, 12mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in ) 5 Steps
4-20 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in) 9 Steps
4-32 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm, 26mm, 28mm, 30mm, 32mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in, 0.87in, 0.94in, 1.02in,1.10in,1.18in,1.26in ) 15 Steps
Main Function Of The Product: M35 cobalt step drill (HSS Co) is a high hardness step drill bit that is mainly applied for drilling high hardness steel, such as, the stainless steel plane and hardened steel.
The M35 step drill bit can be utilized to drill holes in the stainless steel plane.
The following points that you need pay attention to:
1. You can use the hand drill and bench drill to drill holes in the stainless steel plane. Use the hand drill for the board whose thickness is within 1 mm/0.04 in, while use the bench drill for the boards whose thickness is about 2-3 mm/0.08-0.12 in;
2. The drilling sped can't be too fast on the stainless steel plate. Hundreds rpm is enough.
3. Please add the water or cutting fluid to cool down during the processing so as to extend the service life of the drill bits.

Specification:
Product Material: HSS Co
Shank: (approx.)
1) 4-32: 10 mm/0.39 in (triangular cylinder shank )
2) 4-20: 8 mm/0.31 in (triangular cylinder shank)
3) 4-12: 6 mm/0.24 in (triangular cylinder shank)
Size: (approx.)
4-12 mm (4mm, 6mm, 8mm, 10mm, 12mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in ) 5 Steps
4-20 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in) 9 Steps
4-32 mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm, 26mm, 28mm, 30mm, 32mm/0.16in, 0.24in, 0.31in, 0.39in, 0.47in, 0.55in, 0.63in, 0.71in, 0.79in, 0.87in, 0.94in, 1.02in,1.10in,1.18in,1.26in ) 15 Steps
Main Function Of The Product: M35 cobalt step drill (HSS Co) is a high hardness step drill bit that is mainly applied for drilling high hardness steel, such as, the stainless steel plane and hardened steel.
The M35 step drill bit can be utilized to drill holes in the stainless steel plane.
The following points that you need pay attention to:
1. You can use the hand drill and bench drill to drill holes in the stainless steel plane. Use the hand drill for the board whose thickness is within 1 mm/0.04 in, while use the bench drill for the boards whose thickness is about 2-3 mm/0.08-0.12 in;
2. The drilling sped can't be too fast on the stainless steel plate. Hundreds rpm is enough.
3. Please add the water or cutting fluid to cool down during the processing so as to extend the service life of the drill bits.