- -43%
6db/tétel TP4056 5V Micro USB 1A 18650 TP4056 Lítium akkumulátortöltő kártya védőtöltő modullal
6db/tétel TP4056 5V Micro USB 1A 18650 TP4056 Lítium akkumulátortöltő kártya védőtöltő modullal
284 Ft
43% megtakarítás
499 Ft
Nincs adó
Product description
Specifications:
Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery,and still retains the input voltage wiring pads, can be very convenient DIY
Module performance:
IInput interface: Type-c USB
The board size: about 2.5 * 1.65 CM
Charge cut-off voltage: 4.2 V / - 1%
Battery overcharge lifting voltage: 4.00 V
Battery discharge termination voltage: 3.2 V
Battery: over-current protection current 3 A
Maximum charging current output: 1000 ma
The battery discharge protection voltage: 3.0 V
The battery overcharge protection voltage: 4.28 V
The input voltage: 4.35-6V (recommended voltage 5V)
Light state: no load the light not bright, red light for recharging, is full of green light.
It can be used for voltage 3.6 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection.
Note:The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly.
Instructions:
Note: The first time you access the battery, it may no voltage between the output OUT and OUT-, then access 5V voltage charge your energy can activate the protection circuit, and the battery from the B B-, then draw a line on the short open also need recharged to activate the protection circuit. Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge.
MICRO USB female and next - pads for the power input, access 5V. B positive then the lithium battery, B- then negative lithium batteries. OUT and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load.
Package including:
6 x TP4056 Type-C USB 5V 1A 18650 Lithium Battery Charger Module
Specifications:
Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery,and still retains the input voltage wiring pads, can be very convenient DIY
Module performance:
IInput interface: Type-c USB
The board size: about 2.5 * 1.65 CM
Charge cut-off voltage: 4.2 V / - 1%
Battery overcharge lifting voltage: 4.00 V
Battery discharge termination voltage: 3.2 V
Battery: over-current protection current 3 A
Maximum charging current output: 1000 ma
The battery discharge protection voltage: 3.0 V
The battery overcharge protection voltage: 4.28 V
The input voltage: 4.35-6V (recommended voltage 5V)
Light state: no load the light not bright, red light for recharging, is full of green light.
It can be used for voltage 3.6 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection.
Note:The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly.
Instructions:
Note: The first time you access the battery, it may no voltage between the output OUT and OUT-, then access 5V voltage charge your energy can activate the protection circuit, and the battery from the B B-, then draw a line on the short open also need recharged to activate the protection circuit. Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge.
MICRO USB female and next - pads for the power input, access 5V. B positive then the lithium battery, B- then negative lithium batteries. OUT and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load.
Package including:
6 x TP4056 Type-C USB 5V 1A 18650 Lithium Battery Charger Module
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
