• -46%

CH340C Micro USB-TTL soros port ISP letöltési modul 5V/3.3V 500mA Cserélje ki a CH340G CH340T-t STM32 51-hez raktáron lévő

CH340C Micro USB-TTL soros port ISP letöltési modul 5V/3.3V 500mA Cserélje ki a CH340G CH340T-t STM32 51-hez raktáron lévő

107 Ft 46% megtakarítás
199 Ft
Nincs adó
 
 
Product Features
1) Chip: CH340C
2) Operating voltage: 5V or 3.3V
3) Data bits: 5bit, 6Bit, 7bit, 8bit
4) stop bits: 1,2
5) Verification: odd, even, no, Mark, space
6) Transmission rate: 50 ~ 2MHz
7) Current limiting fuse: 500ma
8) Operating system: Windows xp, win7,8,10
9) Operating temperature: -40 ° ~ 85 °
10) Size: 10.4mmx28.5mm
 
Driver IC
 
CH340 is a USB bus adapter chip, to achieve USB to serial or USB to print port.
CH340 built-in independent transceiver buffer, support for simplex, half duplex or full duplex asynchronous serial communication. The serial data includes one low-level start bit, 5, 6, 7 or 8 data bits, one or two high-level stop bits, and supports odd parity / even parity / flag check / blank Test.
CH340 support common communication baud rate: 50,75,100,110,134.5,150,300,600,900,1200,1800,2400,3600,4800,9600,14400,19200,28800,33600,38400,56000, Lt; / RTI & gt; and & lt; RTI ID = 0.0 & gt;
 
Development board power supply
 
The following are the same as the "
CH340 chip supports 5V supply voltage or 3.3V supply voltage. When using 5V operating voltage, CH340 chip VCC pin input 5V power supply, and V3 pin should be an external capacity of 0.1uF power decoupling capacitor. When using 3.3V operating voltage, CH340 chip V3 pin should be connected with the VCC pin, while the external input 3.3V power supply, and with the CH340 chip connected to other circuits can not exceed the operating voltage of 3.3V.
Module defaults to 5V operating voltage, the chip voltage from the USB interface, if you want to change to 3.3V operating voltage, you need to back the module 5V, 3.3V working voltage selection point to switch to the middle point and another point shorted. At this point need to VCC feet to the module input 3.3V power supply, the module can work
Mennyiség

 

Biztonsági feltételek

 

Szállításii feltételek

 

Visszaküldési feltételek

CH340C Micro USB-TTL soros port ISP letöltési modul 5V/3.3V 500mA Cserélje ki a CH340G CH340T-t STM32 51-hez raktáron lévő vonalakkal
CH340C Micro USB to TTL Serial Port ISP Download Module 5V/3.3V 500mA Replace CH340G CH340T For STM32 51 With Lines In Stock
 
 
Product Features
1) Chip: CH340C
2) Operating voltage: 5V or 3.3V
3) Data bits: 5bit, 6Bit, 7bit, 8bit
4) stop bits: 1,2
5) Verification: odd, even, no, Mark, space
6) Transmission rate: 50 ~ 2MHz
7) Current limiting fuse: 500ma
8) Operating system: Windows xp, win7,8,10
9) Operating temperature: -40 ° ~ 85 °
10) Size: 10.4mmx28.5mm
 
Driver IC
 
CH340 is a USB bus adapter chip, to achieve USB to serial or USB to print port.
CH340 built-in independent transceiver buffer, support for simplex, half duplex or full duplex asynchronous serial communication. The serial data includes one low-level start bit, 5, 6, 7 or 8 data bits, one or two high-level stop bits, and supports odd parity / even parity / flag check / blank Test.
CH340 support common communication baud rate: 50,75,100,110,134.5,150,300,600,900,1200,1800,2400,3600,4800,9600,14400,19200,28800,33600,38400,56000, Lt; / RTI & gt; and & lt; RTI ID = 0.0 & gt;
 
Development board power supply
 
The following are the same as the "
CH340 chip supports 5V supply voltage or 3.3V supply voltage. When using 5V operating voltage, CH340 chip VCC pin input 5V power supply, and V3 pin should be an external capacity of 0.1uF power decoupling capacitor. When using 3.3V operating voltage, CH340 chip V3 pin should be connected with the VCC pin, while the external input 3.3V power supply, and with the CH340 chip connected to other circuits can not exceed the operating voltage of 3.3V.
Module defaults to 5V operating voltage, the chip voltage from the USB interface, if you want to change to 3.3V operating voltage, you need to back the module 5V, 3.3V working voltage selection point to switch to the middle point and another point shorted. At this point need to VCC feet to the module input 3.3V power supply, the module can work
4000537338539/1 - simplerob
4000537338539/1

Hasonló kategóriák mint 16 :

Reviews

Write your review

CH340C Micro USB-TTL soros port ISP letöltési modul 5V/3.3V 500mA Cserélje ki a CH340G CH340T-t STM32 51-hez raktáron lévő

 
 
Product Features
1) Chip: CH340C
2) Operating voltage: 5V or 3.3V
3) Data bits: 5bit, 6Bit, 7bit, 8bit
4) stop bits: 1,2
5) Verification: odd, even, no, Mark, space
6) Transmission rate: 50 ~ 2MHz
7) Current limiting fuse: 500ma
8) Operating system: Windows xp, win7,8,10
9) Operating temperature: -40 ° ~ 85 °
10) Size: 10.4mmx28.5mm
 
Driver IC
 
CH340 is a USB bus adapter chip, to achieve USB to serial or USB to print port.
CH340 built-in independent transceiver buffer, support for simplex, half duplex or full duplex asynchronous serial communication. The serial data includes one low-level start bit, 5, 6, 7 or 8 data bits, one or two high-level stop bits, and supports odd parity / even parity / flag check / blank Test.
CH340 support common communication baud rate: 50,75,100,110,134.5,150,300,600,900,1200,1800,2400,3600,4800,9600,14400,19200,28800,33600,38400,56000, Lt; / RTI & gt; and & lt; RTI ID = 0.0 & gt;
 
Development board power supply
 
The following are the same as the "
CH340 chip supports 5V supply voltage or 3.3V supply voltage. When using 5V operating voltage, CH340 chip VCC pin input 5V power supply, and V3 pin should be an external capacity of 0.1uF power decoupling capacitor. When using 3.3V operating voltage, CH340 chip V3 pin should be connected with the VCC pin, while the external input 3.3V power supply, and with the CH340 chip connected to other circuits can not exceed the operating voltage of 3.3V.
Module defaults to 5V operating voltage, the chip voltage from the USB interface, if you want to change to 3.3V operating voltage, you need to back the module 5V, 3.3V working voltage selection point to switch to the middle point and another point shorted. At this point need to VCC feet to the module input 3.3V power supply, the module can work

Write your review