- -40%
1S/2s/3s/4s/5s/6s/7s/8s alacsony feszültségű hangjelző riasztó Lipo akkumulátor feszültségjelző teszter
1S/2s/3s/4s/5s/6s/7s/8s alacsony feszültségű hangjelző riasztó Lipo akkumulátor feszültségjelző teszter
166 Ft
40% megtakarítás
277 Ft
Nincs adó
TMBB
Module wholesale, professional distribution of electronic components. Our products are wholesale prices, priority is given to large quantities. Products are of higher quality than the market and can be purchased with confidence.
Product description
Product introduction: The motor drive module is very suitable for use on battery-powered smart cars, toy cars, robots, etc. The power supply voltage is 2V ~ 10V, which can drive two DC motors or a 4-wire 2-phase stepper motor at the same time. The function of forward and reverse and speed regulation, each current can reach 1.5A continuous current, the peak current can reach 2.5A, has thermal protection and can automatically recover. Product Highlights: 1. Imported original professional motor driver chip, built-in low-conductance internal resistance MOS switch tube, with minimal heat generation, no heat sink, small size, power saving, ideal for your battery power supply. (L298N is a transistor switch, which has low efficiency, high heat generation, heat dissipation, bulky volume, and the L298N on the market is extremely easy to burn out. None of the original chips are used. This product can be a perfect replacement. 2. Dual 1.5A * 2, peak current can reach 2.5A, built-in overheating protection circuit, don't be afraid of motor stalling and burning, it will recover automatically when temperature drops. (The voltage and current of smart cars on the market are within this range) 3. Small size, light weight, 0 standby current, ideal for your model car Product parameters: Dual H-bridge motor drive, can drive two DC motors or a 4-wire two-phase stepper motor at the same time; Module power supply voltage 2V-10V; Signal terminal input voltage 1.8-7V; Single-channel working current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA); Built-in anti-common state conduction circuit, when the input terminal is floating, the motor will not malfunction. Built-in overheat protection circuit (TSD) with hysteresis effect, no need to worry about motor stalling; Product size: 24.7 * 21 * 5mm (length, width, height), ultra-small size, suitable for assembly and vehicle; Mounting hole diameter: 2 mm. Weight: 5g data: INx is connected to the microcontroller IO or other signal source, and MOTOR-A and MOTOR-B are connected to the motor. DC motor drive logic truth table: Precautions: 1. The positive and negative poles of the power supply are reversed, which will definitely cause circuit damage. 2. The output is short-circuited to ground or the output terminal is short-circuited, and the motor is blocked, the chip will be thermally protected, but the chip will be burned when the voltage is close to or exceeds 10V and the peak current greatly exceeds 2.5A.
Module wholesale, professional distribution of electronic components. Our products are wholesale prices, priority is given to large quantities. Products are of higher quality than the market and can be purchased with confidence.
Product description
Product introduction: The motor drive module is very suitable for use on battery-powered smart cars, toy cars, robots, etc. The power supply voltage is 2V ~ 10V, which can drive two DC motors or a 4-wire 2-phase stepper motor at the same time. The function of forward and reverse and speed regulation, each current can reach 1.5A continuous current, the peak current can reach 2.5A, has thermal protection and can automatically recover. Product Highlights: 1. Imported original professional motor driver chip, built-in low-conductance internal resistance MOS switch tube, with minimal heat generation, no heat sink, small size, power saving, ideal for your battery power supply. (L298N is a transistor switch, which has low efficiency, high heat generation, heat dissipation, bulky volume, and the L298N on the market is extremely easy to burn out. None of the original chips are used. This product can be a perfect replacement. 2. Dual 1.5A * 2, peak current can reach 2.5A, built-in overheating protection circuit, don't be afraid of motor stalling and burning, it will recover automatically when temperature drops. (The voltage and current of smart cars on the market are within this range) 3. Small size, light weight, 0 standby current, ideal for your model car Product parameters: Dual H-bridge motor drive, can drive two DC motors or a 4-wire two-phase stepper motor at the same time; Module power supply voltage 2V-10V; Signal terminal input voltage 1.8-7V; Single-channel working current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA); Built-in anti-common state conduction circuit, when the input terminal is floating, the motor will not malfunction. Built-in overheat protection circuit (TSD) with hysteresis effect, no need to worry about motor stalling; Product size: 24.7 * 21 * 5mm (length, width, height), ultra-small size, suitable for assembly and vehicle; Mounting hole diameter: 2 mm. Weight: 5g data: INx is connected to the microcontroller IO or other signal source, and MOTOR-A and MOTOR-B are connected to the motor. DC motor drive logic truth table: Precautions: 1. The positive and negative poles of the power supply are reversed, which will definitely cause circuit damage. 2. The output is short-circuited to ground or the output terminal is short-circuited, and the motor is blocked, the chip will be thermally protected, but the chip will be burned when the voltage is close to or exceeds 10V and the peak current greatly exceeds 2.5A.
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
