- -43%
Mérete: 15 cm - ESP8285WiFi modul ESP-M3 soros port vezeték nélküli áteresztő vezérlő modul teljesen kompatibilis az
Mérete: 15 cm - ESP8285WiFi modul ESP-M3 soros port vezeték nélküli áteresztő vezérlő modul teljesen kompatibilis az
181 Ft
43% megtakarítás
318 Ft
Nincs adó
AT the firmware:
This firmware only supports AT instructions to operate on modules
Transparent firmware:
This firmware is configured through a web page module, similar to router configuration
What is a ESP8285?
ESP8285=ESP8266 1M Flash, make it can withstand high temperature up to 125 degrees Celsius! And the original ESP8266 source code procedures can be used intact transplant.
The core processor of ESP-M3 module adopts the cost-effective chip ESP8285. The chip integrates an enhanced version of Tensilica's L106 Diamond series 32-bit core processor with on-chip SRAM in a smaller size package. The ESP8285 has a full Wi-Fi network capability and can be used independently or as a slave with other host MCUS. When ESP8285 hosts an application, it can be launched directly from external Flash. Built-in cache memory helps to improve system performance and optimize the storage system. In addition, the ESP8285 can be used as a Wi-Fi adapter simply through the SPI/SDIO interface or I2C/UART interface for any microcontroller-based design.
1) Super small size;
2) Serial port to WiFi;
3) Wireless transparent transmission;
4) Long-distance ultra-low power consumption;
5) High temperature resistance, up to 125℃;
6) Fully compatible with ESP8266, source code can be used intact transplant.
Features:
SOC features
Built-in Tensilica L106 ultra-low power 32-bit microprocessor, 80MHz and 160MHz, RTOS support
Built-in TCP/IP protocol stack
Built-in 1 channel 10 bit high precision ADC
Peripheral interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
The deep sleep retention current is 10uA, and the turn-off current is less than 5uA
Wake up, connect, and transmit packets within 2 ms
Power consumption in standby state less than 1.0MW (DTIM3)
Built-in 1 MB SPI Flash
Wi-fi features
Support 802.11 b/g/n/e/I
Supports Station, SoftAP, and SoftAP STA modes
Support wi-fi Direct (P2P)
Supports hardware acceleration of CCMP(CBC-MAC, counter mode), TKIP(MIC, RC4), WAPI(SMS4), WEP(RC4), and CRC
P2P discovery, P2P GO /GC mode and P2P power management
WPA/PA2 PSK and WPS
802.11i security features: preauthentication and TSN
Support for 802.11n (2.4 GHz)
802.1 h/RFC1042 frame encapsulation
Seamless Roaming support
Support AT remote upgrade and cloud OTA upgrade
Smart Config (including Android and iOS devices)
Module peripherals
2xUART
1xADC
1xEn
1X wake up pin
1xHSPI
1xI2C
1xI2S
More than 10 xgpios
Operating temperature range: -40℃-125℃
Module size: 26.8mm*16mm
Application scenarios
● Home Appliances ● Home automation
● Intelligent socket, intelligent lamp ● Mesh network
● Baby monitor ● IP camera
● Sensor networks ● Wearable electronics
● Secure ID tags ● Wireless location awareness
● Wireless positioning system beacon ● Industrial wireless control
This firmware only supports AT instructions to operate on modules
Transparent firmware:
This firmware is configured through a web page module, similar to router configuration
What is a ESP8285?
ESP8285=ESP8266 1M Flash, make it can withstand high temperature up to 125 degrees Celsius! And the original ESP8266 source code procedures can be used intact transplant.
The core processor of ESP-M3 module adopts the cost-effective chip ESP8285. The chip integrates an enhanced version of Tensilica's L106 Diamond series 32-bit core processor with on-chip SRAM in a smaller size package. The ESP8285 has a full Wi-Fi network capability and can be used independently or as a slave with other host MCUS. When ESP8285 hosts an application, it can be launched directly from external Flash. Built-in cache memory helps to improve system performance and optimize the storage system. In addition, the ESP8285 can be used as a Wi-Fi adapter simply through the SPI/SDIO interface or I2C/UART interface for any microcontroller-based design.
1) Super small size;
2) Serial port to WiFi;
3) Wireless transparent transmission;
4) Long-distance ultra-low power consumption;
5) High temperature resistance, up to 125℃;
6) Fully compatible with ESP8266, source code can be used intact transplant.
Features:
SOC features
Built-in Tensilica L106 ultra-low power 32-bit microprocessor, 80MHz and 160MHz, RTOS support
Built-in TCP/IP protocol stack
Built-in 1 channel 10 bit high precision ADC
Peripheral interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO
The deep sleep retention current is 10uA, and the turn-off current is less than 5uA
Wake up, connect, and transmit packets within 2 ms
Power consumption in standby state less than 1.0MW (DTIM3)
Built-in 1 MB SPI Flash
Wi-fi features
Support 802.11 b/g/n/e/I
Supports Station, SoftAP, and SoftAP STA modes
Support wi-fi Direct (P2P)
Supports hardware acceleration of CCMP(CBC-MAC, counter mode), TKIP(MIC, RC4), WAPI(SMS4), WEP(RC4), and CRC
P2P discovery, P2P GO /GC mode and P2P power management
WPA/PA2 PSK and WPS
802.11i security features: preauthentication and TSN
Support for 802.11n (2.4 GHz)
802.1 h/RFC1042 frame encapsulation
Seamless Roaming support
Support AT remote upgrade and cloud OTA upgrade
Smart Config (including Android and iOS devices)
Module peripherals
2xUART
1xADC
1xEn
1X wake up pin
1xHSPI
1xI2C
1xI2S
More than 10 xgpios
Operating temperature range: -40℃-125℃
Module size: 26.8mm*16mm
Application scenarios
● Home Appliances ● Home automation
● Intelligent socket, intelligent lamp ● Mesh network
● Baby monitor ● IP camera
● Sensor networks ● Wearable electronics
● Secure ID tags ● Wireless location awareness
● Wireless positioning system beacon ● Industrial wireless control
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
