- -43%
Áramáramlási feszültség modul 0/4-20mA - 0-3.3V5V10V feszültségadó jelátalakító kondicionálás
Áramáramlási feszültség modul 0/4-20mA - 0-3.3V5V10V feszültségadó jelátalakító kondicionálás
113 Ft
43% megtakarítás
199 Ft
Nincs adó
Product Introduction:
In the process of circuit signal transmission, the voltage signal will weaken with the increase of transmission distance, and the current transmission can avoid the signal weakening. This module is used at the end of current signal transmission to convert the signal into voltage signal for detection by single chip microcomputer. Current input supports 4-20mA, 0-20mA, voltage output supports 0-3.3V 0-5V 0-10V.
Product highlights:
Wide power supply voltage range, output voltage support multiple ranges;
Zero and full range can be adjusted;
High stability, good linearity, industrial grade;
Current signal sampling resistance adopts high precision color ring resistance, high precision, small temperature drift, large power.
Instructions:
1. The module is connected according to the definition, and the power supply voltage is 7-36V (if the output reaches 10V, the power supply voltage must be greater than 12V).
2. After the server is powered on, the D2 indicator is on. Otherwise, check the cable connection. Board with reverse connection protection, reverse connection does not burn.
3. When the current input is low (0mA or 4mA), adjust the ZERO potentiometer so that the VOUT output is low (0.0V or other voltage).
4. When the current input is value (20mA), adjust the SPAN potentiometer so that the VOUT output is value (3.3V or 5V or 10V, when the input is 4-20MA, the output can be as small as 2.5V).
According to your requirements, select the corresponding range by jumper cap:
4-- 20MA: 0--2.5V range: J1 1, 2 pin short, 3, 4 pin short
0--3.3V range: J1 1, 2 pin disconnect, 3, 4 pin disconnect
0--5.0V range: J1 1, 2 pin short, 3, 4 pin short
0--10.0V range: J1 1, 2 pin short, 3, 4 pin disconnected
0-- 20MA: 0--3.3V range: J1 1, 2 pin short, 3, 4 pin short
0--5.0V range: J1 1, 2 pin short, 3, 4 pin short
0--10.0V range: J1 1, 2 pin short, 3, 4 pin disconnected
In the process of circuit signal transmission, the voltage signal will weaken with the increase of transmission distance, and the current transmission can avoid the signal weakening. This module is used at the end of current signal transmission to convert the signal into voltage signal for detection by single chip microcomputer. Current input supports 4-20mA, 0-20mA, voltage output supports 0-3.3V 0-5V 0-10V.
Product highlights:
Wide power supply voltage range, output voltage support multiple ranges;
Zero and full range can be adjusted;
High stability, good linearity, industrial grade;
Current signal sampling resistance adopts high precision color ring resistance, high precision, small temperature drift, large power.
Instructions:
1. The module is connected according to the definition, and the power supply voltage is 7-36V (if the output reaches 10V, the power supply voltage must be greater than 12V).
2. After the server is powered on, the D2 indicator is on. Otherwise, check the cable connection. Board with reverse connection protection, reverse connection does not burn.
3. When the current input is low (0mA or 4mA), adjust the ZERO potentiometer so that the VOUT output is low (0.0V or other voltage).
4. When the current input is value (20mA), adjust the SPAN potentiometer so that the VOUT output is value (3.3V or 5V or 10V, when the input is 4-20MA, the output can be as small as 2.5V).
According to your requirements, select the corresponding range by jumper cap:
4-- 20MA: 0--2.5V range: J1 1, 2 pin short, 3, 4 pin short
0--3.3V range: J1 1, 2 pin disconnect, 3, 4 pin disconnect
0--5.0V range: J1 1, 2 pin short, 3, 4 pin short
0--10.0V range: J1 1, 2 pin short, 3, 4 pin disconnected
0-- 20MA: 0--3.3V range: J1 1, 2 pin short, 3, 4 pin short
0--5.0V range: J1 1, 2 pin short, 3, 4 pin short
0--10.0V range: J1 1, 2 pin short, 3, 4 pin disconnected
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
