XY-DJ01 egyirányú relémodul késleltetett kikapcsolás és leválasztás kioldó késleltetési ciklus időzítő áramkör kapcsoló
XY-DJ01 one way relay module delay power off and disconnect triggering delay cycle timing circuit switch
Product highlights:
 
1. With LCD display, the current mode and parameters at a glance, very clear, simple and practical;
 
2. Support button trigger control, high and low level trigger, switching control, support NPN,PNP sensor access, suitable for most occasions;
 
Wide voltage power supply (6~30V), guide rail installation, very convenient to use;
 
4. One-button pause function, with reverse connection protection, reverse connection does not burn;
 
5. Added the sleep mode, after enabling, no operation for about 5 minutes, automatically turn off the LCD backlight; Any key wake up;
 
6. Different OP, CL, LOP parameters can be set. These parameters are independent of each other and stored separately.
 
7. All parameters are automatically saved after power failure.
 
Working Mode:
 
P0: After the signal is triggered, the relay turns on for OP time and then disconnects. During OP time, the signal triggers again without effect
 
P1: After the signal is triggered, the relay turns on OP time and then disconnects; During OP time, the signal triggers a re-timing again
 
P2: After the signal is triggered, the relay turns on OP time and then disconnects; Within the OP time, the signal triggers a reset again, the relay disconnects, and the timing stops
 
P3: After the signal is triggered, the relay disconnects for CL time and then turns on;
 
P4: The trigger signal is given, and the relay disconnects the CL time after the OP time is turned on. Then the above action is cycled, and the signal is given again within the cycle to restore the initial state and stop the timing. The number of cycles (LOP) can be set; The cycle ends, keep the relay disconnected;
 
P5: Trigger signal is given. After the relay disconnects CL time, the relay turns on OP time, and then the above action is cycled. Signal is given again within the cycle to restore the initial state and stop timing. The number of cycles (LOP) can be set; The end of the cycle, keep the relay on;
 
P6: After powering on, no trigger signal is required, the relay is on OP time, the relay is off CL time, and the above action is repeated; The number of cycles (LOP) can be set; The cycle ends, keep the relay disconnected;
 
P7: After powering on, no trigger signal is required. The above action is repeated when the relay disconnects CL and when the relay turns on OP. The number of cycles (LOP) can be set; The end of the cycle, keep the relay on;
 
P8: Signal holding function if there is a trigger signal, the timing is cleared and the relay remains on; When the signal disappears, disconnect the relay after timing OP; During the time, there is a signal, the time is cleared;
 
P9: Signal holding function If there is a trigger signal, the timing is cleared and the relay remains disconnected; When the signal disappears, the timing CL is turned on after the relay; During the time, there is a signal, the time is cleared;
 
Product parameters:
 
1: working voltage: 6--30V power supply
 
2: Trigger signal source: high level trigger (3.0V~24V), low level trigger (0.0V~0.2V), switching quantity control (passive switch).
 
3: output capacity: can control dc 30V 30A or AC 220v 30A equipment
 
4: static current: 15mA Working current: 50-130mA
 
5: service life: more than 100,000 times; Operating temperature: -40 -- 85℃;
 
6: with light coupling isolation, enhance anti-interference ability, industrial grade circuit board, set parameters after power off forever memory.
 
Timing range
 
0.01 second (small) to 9999 minutes () continuous adjustable
 
How to select timing range:
 
In the OP/CL parameter modification interface, press the pause button and select the timing range;
 
XXXX has no decimal point, and the timing range is 1 to 9999 seconds
 
XXX.X decimal point in the tens place, timing range 0.1 to 999.9 seconds
 
XX.XX decimal point in the hundreds, timing range 0.01 to 99.99 seconds
 
X decimal point is on. The timing range is 1 to 9999 minutes
 
For example, if you want to set the OP to 3.2 seconds, move the decimal point to the tens place and display 003.2
 
OP conduction time, CL disconnection time, LOP cycles (1 -- 9999, ---- stands for infinite cycles)
 
1. Parameter Settings
 
A) Long press the setting button to enter the setting interface;
 
B) First set the working mode, the working mode flashing reminder, by pressing the increase/decrease button to set the working mode;
 
C) Press the setting button, select the working mode, and enter the system parameter setting;
 
D) On the system parameter setting interface, press the setting button to switch the system parameter to be modified, and press the Add/decrease button to modify;
 
(Note: short press setting button in P0~P3/P8/P9 mode is invalid);
 
E) In the OP/CL parameter modification interface, press the pause button to switch the timing unit (1s/0.1s/0.01s/1min);
 
F) After all parameters are set, long press the set button to save parameter Settings and exit the setting interface;
 
Second, additional functions
 
A) Automatic sleep function: In the operation interface (P0~P7 mode), long press the pause button to start or turn off the automatic sleep function (L-P select ON to start the sleep function, about five minutes, no operation, LCD backlight automatically shut down, the system runs normally, any key to wake up; Off turns off the sleep function);
 
B) Parameter viewing: In the operation interface, press the SET key to display the current parameter Settings of the system without affecting the normal operation of the system;
 
C) Display content switching: in P4 ~ P7 mode, press DOWN button to switch display content (running time/cycle times);
 
1005004199540745. - fareast