433Mhz Wireless Transmitter and Receiver Module Learning Code EV1527 Decoding Module 4CH output With Learning Button DIY remote
Wide Availability
Remote control switch, receiver module, motorcycles, automobile anti-theft products, home security products, electric doors, shutter doors, windows, remote control socket, remote control LED, remote audio remote control electric doors, garage door remote control, remote control retractable doors, remote volume gate, pan doors, remote control door opener, door closing device control system, remote control curtains, alarm host, alarm, remote control motorcycle remote control electric cars, remote control MP3.
Applications
1.wireless power switch, socket, remote control switch, receiver module,
2. access control, electric cars, motorcycles, automobile anti-theft products, remote door openers, closers control system
3. security, surveillance systems, home security products, electric doors, alarm host, alarm
4. rooms controls, shutter doors, windows, remote control socket, remote control LED, remote audio remote control electric doors, garage door remote control, remote control retractable doors, remote rolling gates, sliding door
5. smart home products, remote control curtains, remote MP3, audio
Product Detail
Receiver module(RX480E)
Working voltage : DC 3.3~5V
Quiescent Current : less than 5MA
Output current: 10mA
Channels: 4 Channels
RF frequency: 433MHz
Frequency band: +0.2MHz, -0.2MHz
Working temperature : -25~+75 degrees
Receiving Sensitivity: -108dB
Amount of storage remote controls: 25 pieces
Support encoding: EV1527 Leaning code
RF Operating mode :ASK superheterodyne wireless reception
Size: 28*12.3*6 (mm)
Receiving range: above 15 meters (Open space)
Remote operating mode: Momentary Mode / Toggle Mode / Latched Mode
Pins Instruction
GND : ground or negative pole
+V : DC3.3~5V input
D0: Data output
D1: Data output
D2: Data output
D3: Data output
VT: Output(When any pin of D0-D3 outputs the level signal, VT is output synchronously, VT is usually used as the output indicator.)
The output: 4 channel CMOS level signal Corresponding to the remote control ABCD 4 buttons.
Application example
Transmitter module( TX118SA-4 )
Working voltage : DC 3V-24V
Channels: 4 Channels
Emission current: 10MA
Rate of fire : maximum: 10KB / S
Transmit deviation: +/- 7. 5KHZ / narrow-band emission
Transmitting power: 11dbm
RF frequency :433MHz
Working temperature: -25~+75 degrees
Size: 18*18*6 (mm)
Support encoding: EV1527 Leaning code
Modulation : ASK
Pins Instruction
- : Negative power supply
+: Positive power supply, DC 3-24V
K1: 1 short to Negative start transmitting data, Similar the A button on the remote control.
K2: 2 short to Negative start transmitting data, Similar the B button on the remote control.
K3: 3 short to Negative start transmitting data, Similar the C button on the remote control.
K4: 4 short to Negative start transmitting data, Similar the D button on the remote control.
ANT: transmitting antenna
Application example
Package include
As the options show.
Operating Mode
You can match the Remote Control with the Receiver Switch Modulein 3modes.
Momentary Mode:
1. Press and hold one button, relay "1" will turn on,
2. Release the button, this relay "1" will turn off.
Toggle Mode:
1. Press button "A", relay "1" will turn on,
2. Press button "A" again, this relay "1" will turn off.
Latched mode:
1. Press button "A", relay "1" will turn on,
2. Press button "B", relay "2" will turn on, at the same time relay "1" will turn off.
Reset
1.Delete the existing data about operating modes
Press the learning button (on the Receiver) 8 times. The existing data will be deleted succeed.
2.Set up
Set up(Momentary)
1. Press the learning button(on the Receiver) once. Wait for 3 seconds,
2. Press button "A" on the remote control. Wait for 3 seconds. Succeed.
Set up(Toggle)
1. Press the learning button(on the Receiver) twice. Wait for 3 seconds,
2. Press one button "A" on the remote control. Wait for 3 seconds. Succeed.
Set up(Latched)
1. Press the learning button(on the Receiver) triple. Wait for 3 seconds,
2. Press button "A" on the remote control. Wait for 3 seconds. Succeed.
On this products details page, there is a demonstration video available.