A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
1x DC-DC 1500W Voltage Step Up Converter Boost CC CV Power Supply Module Parts
Product description:
This is a long-life non-isolated DC power converter module.
High power and stable output, it converts 10-60VDC to 12-97VDC.
High-quality components can ensure a high conversion efficiency of up to 97% .
The fan is designed with intelligent temperature control, it will work automatically when the temperature reaches about 60degree Celsius, and it will stop working when the temperature drops below 60degree Celsius.
It is widely used in high-power solar street lamp drivers, various LED lighting CV drivers, vehicle and mobile equipment power supplies, DIY adjustable CV CC power supplies, solar charging and various battery charging.
Product parameters:
Name: 1500W boost constant current module
Type: Non-isolated boost module (BOOST)
Input voltage: DC10V to 60V
Input current: 10V-30V input voltage, the maximum current is 35A-40A; 31-60V input voltage, the maximum current is 30A-35A
Quiescent current: 15mA (when converting 12V to 20V, higher output voltage will increase quiescent current)
Output voltage: 12-97V continuously adjustable (cannot be used for step-down)
Output current: 22A (related to the input and output voltage difference, the greater the voltage difference, the smaller the output current. When the current exceeds 15A, please strengthen heat dissipation)
Constant current range: 0.8-22A ( /- 0.3A)
Reverse input protection: Yes (150A power MOS reverse protection)
Input low voltage protection: Yes (10V-50V adjustable, can be automatically restored)
Working temperature: -40degree Celsius to 85degree Celsius (if the temperature is too high, please strengthen heat dissipation)
Frequency: 150KHz
Conversion efficiency: 92% to 97% (The efficiency is related to the input/output voltage, current and voltage difference. The smaller the difference, the higher the efficiency)
Input overcurrent protection: Yes (automatic protection when the input is greater than 40A, and the power supply voltage will not increase)
Short circuit protection: Yes (input 60A fuse), please be careful not to cause a short circuit.
Reverse input protection: Yes ((150A power MOS tube, can be reverse connected for a long time)
Installation method: four 3mm brackets
Wiring method: terminal block (please use high current copper wire)
Output power: maximum output power = input voltage * 30A (if input 12V, the maximum output power = 12V * 30A = 360W)
(If 24V is input, the maximum output power = 24V * 30A = 720W)
Weight: 372 grams / 13.1 ounces (approximately)
Note: The output of the module should not be short-circuited or use a multimeter to directly measure the current. Short-circuit will burn the module.
Undervoltage adjustable range: DC10V-50V (clockwise increase, counterclockwise decrease), first adjust the undervoltage to the minimum, then adjust the input voltage to the required undervoltage protection value, slowly adjust the undervoltage clockwise Increase the pressure value; when the under-voltage lamp is on, turn it counterclockwise for one turn, and then restart the machine.
Input under-voltage protection is mainly used to prevent battery over-discharge when the input power is battery. Too low battery voltage will damage the power module and battery. When the input is a switching power supply, low voltage protection is also required.
Constant voltage adjustable range: DC12-97V (clockwise increase, counterclockwise decrease), first adjust the voltage to the required voltage, and then connect to the load.
Constant current adjustable range: 0.8-22A (clockwise increase, counterclockwise decrease), first disconnect the load, then adjust the output voltage to the required voltage, and adjust the current to the minimum (turn the CC potentiometer counterclockwise for approximately 30 turns), connect the ammeter in series to the output, and then slowly adjust the current. (The booster module cannot directly adjust the current through a short circuit)
The input voltage should not be lower than 10V or higher than 60V (when the input voltage is lower than 12V, please reduce the load appropriately).
Make sure that the input voltage is at least 2V lower than the output voltage.
If using a switching power supply or other auxiliary power supply, make sure that the power supply is greater than or equal to 1.3 times the power supply of the power supply module.
During over-current or under-voltage protection, the output will still have a voltage close to the input voltage, and protection means no boost voltage.
Packing list:
1 * module
Note:
1. The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. Please allow slight manual measurement deviation for the data.
402551974678 - shoppingelectricaleq (31)