50db 3D nyomtató StepStick DRV8825 léptetőmotoros meghajtó hordozójavító 4 rétegű PCB RAMPS
50pcs 3D Printer StepStick DRV8825 Stepper Motor Drive Carrier Reprap 4-layer PCB RAMPS
The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications.
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 - 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
1Simple step and direction control interface
2Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
3Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates
445 V maximum supply voltage
5Built-in regulator (no external logic voltage supply needed)
6Can interface directly with 3.3 V and 5 V systems
7Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
8Short-to-ground and shorted-load protection
94-layer, 2 oz copper PCB for improved heat dissipation
10Exposed solderable ground pad below the driver IC on the bottom of the PCB
11Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)
 
 
 
This product is a carrier board or breakout board for TI's DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver's key features: 
Simple step and direction control interface 
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates 
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 
45 V maximum supply voltage 
Built-in regulator (no external logic voltage supply needed) 
Can interface directly with 3.3 V and 5 V systems 
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout 
Short-to-ground and shorted-load protection 
4-layer, 2 oz copper PCB for improved heat dissipation 
Exposed solderable ground pad below the driver IC on the bottom of the PCB 
Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information) 
We also carry a DRV8824 stepper motor driver carrier that can serve as a direct substitute for the DRV8825 carrier when using lower-current stepper motors. The DRV8824 can only deliver up to 0.75 A per coil without a heat sink (1.2 A max with proper cooling), but it has larger current-sense resistors that allow for better microstepping performance than the DRV8825 carrier at low currents. The only way to tell our DRV8824 carrier apart from the DRV8825 carrier is by the markings on the driver IC; if you have a mix of the two, you might consider marking them (there is a blank square on the bottom silkscreen you can use for this). For lower-voltage applications, consider our pin-compatible DRV8834 carrier, which works with motor supply voltages as low as 2.5 V. 
This product ships with all surface-mount components—including the DRV8825 driver IC—installed as shown in the product picture.
 
 
32292363148 - tenstar