TMS374 ECU dekóder a Renault Immo Killer Matizhoz TMS374 Compiler Frequency MCU Automotive Diagnostic Tool Shippng
TMS374 ECU Decoder for Renault Immo Killer Matiz TMS374 Compiler Frequency MCU Automotive Diagnostic Tool Shippng
TMS374 ECU Decoder for Renault Immo Killer Matiz TMS374 Compiler Frequency MCU Automotive Diagnostic Tool Free Shippng
TMS374 ECU Decoder
Top 4 Reasons To Get TMS374 ECU Decoder
1. Power the sweeper and ECU
2. Connect the GND line to any suitable GND on the ECU
3. Connect the Data line to the Reset pin on the 27C512 or 28F512
4. Without the need of a laptop
TMS-374 Decoder ECU info:
A small tiny2313 MCU is used to generate the pulses instead of the PC RS232 Tx line. The TMS 374 software is in fact a simple frequency sweeper with an effective range from about 2000Hz to about 100Hz. The Tiny sweeper does exactly the same but much more better (bigger range).
After powering the device on - the LED should blink twice. Pressing the button will start the sweep procedure. LED ON - means there are pulses on the output. After reaching the lowest frequency the LED goes off and the mcu stops the generation.
Connection diagram:
: 12v DC
- : GND
S : signal wire
Manual:
After powering the device on - the LED should blink twice. The sweeping process starts as power is supplied to the device. LED ON - means there are pulses on the output.
After reaching the lowest frequency the LED goes off and the mcu stops the generation.
* Connect the GND line to any suitable GND on the ECU via the small grabber.
* Connect the Data line to the Reset pin on the EPROM via the small grabber.
* Power the ECU and then the sweeper, the sweeper will flash twice on power up.
* Press the button and the device will start sweeping, once the LED turns off your done.
* Cut the immo data line on the ECU before re-fitting back to car.
The sweeper should work with the following ECUs:
for renault SIEMENS Fenix 3 and 5
for r enault  Megane 1400cc 8v
for r enault  Megane 1600cc 8v
for r enault  Megane 2000cc 8v
for r enault  Megane 2000cc 16V
for r enault  Megane Scenic 1400cc 8v
for r enault  Megane Scenic 1600cc 8v
for r enault  Megane Scenic 2000cc 8v
for r enault  Sefrane 2000cc 16V
for r enault  Laguna 2000cc 8v
for r enault  Laguna 2000cc 16v
for r enault  Espace 2000cc 8v
for r enault  SAGEM SAFIR 1 and 2
for r enault  Clio 1200cc 8V
for r enault  Clio 1400cc 8V
for r enault  Clio 1600cc 8V
for r enault  Clio 2000cc 16V Williams
for r enault  Laguna 1800cc 8V
for r enault  Laguna 2000cc 8V
for r enault  Laguna 1800cc 16V
for r enault  Laguna 2000cc 16V
for r enault  Twingo 1200cc 8V
NOTE:If reset pin is connected to ground then it must be lifted or the track cut before decoding. This can be re-attached after decoding the ecu.
As a rule of thumb keep the power connected to the ECU for a futher five minutes after the decoder has completed the decoding process.
for Sagem SL96 Psa
for  Peugeot 306 1400cc 8V
for  Peugeot 306 1600cc 16V
for  Peugeot 306 1800 16V
for  Peugeot Ranch 1400 8V
for  Citroen Berlingo 1400cc 8V
for  Citroen Xrara 1400cc 8V
for Citroen Xrara 1800cc 16V
for hyundai SIEMENS
for h yundai Coupe 1600cc 16V
for h 2000cc 16V Hyundai Coupe
for KIA SIEMENS
for Kia Rio 1300 16V
for Kia Rio 1500 16V
for MAGNETI MARELLI
1AP20, 1AP40, 1AP41, 1AP43, 1AP80, 1AP81, 1AP83 1AP90,
for Citroen Berlingo 1800cc 8V
for Citroen Saxo 1400cc 8V
for Citroen Saxo 1600cc 16V
for Citroen Xara 1400cc 8V
for Citroen Xara 1800cc 8V
for Citroen Xara 2000cc 16V
for Citroen ZX 1400cc 8V
for Peugeot 106 1400cc 8V
for Peugeot 106 1600cc 8V
for Peugeot 106 1600cc 16V
for Peugeot 206 1100cc 8V
for Peugeot 206 1400cc 8V
for Peugeot 306 1400cc 8V
for Peugeot 306 1600cc 8V
for Peugeot 306 1800cc 8V
for the Peugeot 405 1800cc 8V
for Peugeot 406 1800cc 8V
for Peugeot Partner 1800 8V
33012387567 - syobd