A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra!
MQ-2 MQ-3 MQ-4 MQ-5 MQ-6 MQ-7 MQ-8 MQ-9 MQ-135 füstérzékelő metán cseppfolyósított gáz érzékelő modul az Arduino kezdő barkácskészlethez
MQ-2 MQ-3 MQ-4 MQ-5 MQ-6 MQ-7 MQ-8 MQ-9 MQ-135 Detection Smoke methane liquefied Gas Sensor Module for Arduino Starter DIY Kit
[Statement] This procedure is used only for study and reference, please indicate the copyright and author information!
************************************************** ******************* /
/ ************************************************* *******************
Note: 1, when the measured concentration is greater than the set density, single-chip IO port output low
************************************************** ******************* /
# Include // library files
#define uchar unsigned char // macro definition unsigned char
#define uint unsigned int // macro definition unsigned int
/ ************************************************* *******************
I / O definitions
************************************************** ******************* /
sbit LED = P1 ^ 0; // define microcontroller P1 port of the first one (ie P1.0) to indicate the end
sbit DOUT = P2 ^ 0; // define the microcontroller P2 port first one (ie P2.0) as an input sensor
/ ************************************************* *******************
Delay function
************************************************** ******************* /
void delay () // delay procedure
{
uchar m, n, s;
for (m = 20; m> 0; m--)
for (n = 20; n> 0; n--)
for (s = 248; s> 0; s--);
}
/ ************************************************* *******************
The main function
************************************************** ******************* /
void main ()
{
while (1) // infinite loop
{
LED = 1; // off P1.0 port lights
if (DOUT == 0) // When the concentration is higher than the set value, the implementation of the Con
{
delay (); // delay interference
When if (DOUT == 0) // determine the concentration higher than the set value, the implementation of the Con
{
LED = 0; // P1.0 port lights lit
}
}
}
}
/ ************************************************* *******************
End
************************************************** ****************** /
 
MQ-135 Product Overview:
Using high-quality dual-panel design,with power indicator and TTL signal output instructions.
The switching signal having a DO (TTL) output and analog output AO.
TTL output valid signal is low. ( Low-level signal when the output light can be directly connected to the microcontroller or relay module )
Analog output voltage with the higher concentration of higher voltage
There are four screw holes for easy positioning.
Has a long life and reliable stability
Rapid response and recovery characteristic
Input voltage : DC5V Power consumption ( current ): 150mA
DO output : TTL digital 0 and 1 ( 0.1 and 5V)
AO output :0.1-0 .3 V ( relative to pollution ) , the maximum concentration of a voltage of about 4V
 
Special note:
After the sensor is powered,needs to warm up around 20S,measured data was stable,heat sensor is a normal phenomenon,because the internal heating wire,if hot is not normal .
 
MQ135 gas sensor sensitive material used in the clean air, low conductivity tin oxide (SnO2). When present in the environment pollution gas sensor, conductivity sensor with the increase in air pollution in the gas concentration increases. Use simple circuit can convert the change in conductivity of the gas concentration corresponding to the output signal.
MQ135 ammonia gas sensor, sulfide, benzene vapor high sensitivity, smoke and other harmful monitoring will also be ideal. The sensor can detect a variety of harmful gases, it is a low-cost sensors for a variety of applications.
 
Application:
Can be used for home and factory gas leakage monitoring devices, suitable for liquefied petroleum gas, butane, propane, methane, smoke, etc.
4000770229872/3 - sitai