- -43%
3S 3.2V - 3s/4s/5s Bms 12v 16.8v 3.2v/3.7v 100a Li-ion Lmo háromkomponensű lítium akkumulátor védő áramköri lap Li
3S 3.2V - 3s/4s/5s Bms 12v 16.8v 3.2v/3.7v 100a Li-ion Lmo háromkomponensű lítium akkumulátor védő áramköri lap Li
307 Ft
43% megtakarítás
539 Ft
Nincs adó
Practical guide:
Output current: separate port 80A; same port 60A
Note: Lithium batteries should be charged with special chargers for lithium batteries. Do not use lead-acid battery chargers. Lead-acid charging may cause high voltage breakdown of the protection board MOS tube, causing the protection board to be overcharged and not protected.
(1) 3-string split-port wiring method (refer to 3-string split-port wiring diagram)
① Connect the 3 battery packs in series according to the battery connection in the 3-string split-port wiring diagram.
②Connect the negative pole of the charger to C- of the protection board, and connect the negative pole of the load to P-.
③Connect the positive poles of the charger and the load to the positive poles of the three strings of batteries.
④Refer to the three-series split-port wiring diagram and use three wires to connect the positive poles of the three battery packs to B , B4, and B3 in sequence.
⑤Connect the negative poles of the three batteries to B-. B1, B2 and B- are shorted.
⑥After all the wires are connected according to the 3-string split-port wiring diagram and checked for correctness, they can be used only after confirming that they are correct.
⑦During use, when the indicator light on the protection board is on, it means that the corresponding battery pack is in a balanced working state (that is, the battery is not balanced at this time).
(2) Wiring method of 3 series with the same port (refer to the wiring diagram of 3 series with the same port)
① Connect the 3 battery packs in series according to the connection method of the battery in the 3-series connection diagram.
②Connect the negative pole of the charger and the negative pole of the load to C-, and leave P- unconnected.
③Connect the positive poles of the charger and the load to the positive poles of the three strings of batteries.
④Refer to the wiring diagram of the three strings with the same port, use three wires to connect the positive poles of the three battery packs to B , B4, and B3 in sequence.
⑤Connect the negative poles of the three batteries to B-. B1, B2 and B- are shorted.
⑥After all the wires are connected according to the three-string same-port wiring diagram and check whether they are correct, they can be used only after confirming that they are correct.
⑦During use, when the indicator light on the protection board is on, it means that the corresponding battery pack is in a balanced working state (that is, the battery is not balanced at this time).
Output current: separate port 80A; same port 60A
Note: Lithium batteries should be charged with special chargers for lithium batteries. Do not use lead-acid battery chargers. Lead-acid charging may cause high voltage breakdown of the protection board MOS tube, causing the protection board to be overcharged and not protected.
(1) 3-string split-port wiring method (refer to 3-string split-port wiring diagram)
① Connect the 3 battery packs in series according to the battery connection in the 3-string split-port wiring diagram.
②Connect the negative pole of the charger to C- of the protection board, and connect the negative pole of the load to P-.
③Connect the positive poles of the charger and the load to the positive poles of the three strings of batteries.
④Refer to the three-series split-port wiring diagram and use three wires to connect the positive poles of the three battery packs to B , B4, and B3 in sequence.
⑤Connect the negative poles of the three batteries to B-. B1, B2 and B- are shorted.
⑥After all the wires are connected according to the 3-string split-port wiring diagram and checked for correctness, they can be used only after confirming that they are correct.
⑦During use, when the indicator light on the protection board is on, it means that the corresponding battery pack is in a balanced working state (that is, the battery is not balanced at this time).
(2) Wiring method of 3 series with the same port (refer to the wiring diagram of 3 series with the same port)
① Connect the 3 battery packs in series according to the connection method of the battery in the 3-series connection diagram.
②Connect the negative pole of the charger and the negative pole of the load to C-, and leave P- unconnected.
③Connect the positive poles of the charger and the load to the positive poles of the three strings of batteries.
④Refer to the wiring diagram of the three strings with the same port, use three wires to connect the positive poles of the three battery packs to B , B4, and B3 in sequence.
⑤Connect the negative poles of the three batteries to B-. B1, B2 and B- are shorted.
⑥After all the wires are connected according to the three-string same-port wiring diagram and check whether they are correct, they can be used only after confirming that they are correct.
⑦During use, when the indicator light on the protection board is on, it means that the corresponding battery pack is in a balanced working state (that is, the battery is not balanced at this time).
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
