Szín: Csak vezérlő - DC 12V akvárium akvárium automatikus táp vezérlő Vízszint érzékelő mágnesszelep Magas Közép
380 Ft43% megtakarítás
666 Ft
Nincs adó
Product Name: DC 12V Fish tank Aquarium automatic supply controller Water Level Sensor Solenoid High Mid Low level LED indicator Board
Package inlcuded: 1 x DC 12V LOW MID HIGH indicators LC66C01 Automatic pumping and pouring controller Module(The probe is 2P Male XH2.54mm Pitch Wire Cable, which can be purchased separately or prepared by yourself.)
Description: 1 Working voltage: DC 12V 2 Standby current 6MA 3 Working current 32MA 4 Size: 63mm X 29mm X 19mm 5 Weight: 20 g 6 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC There are two purposes for connecting the NO and NC ports of the relay: The water pump is connected to the COM NC port to automatically fill the water tower The water pump is connected to the COM NO port to automatically pump water from the water tower Note: 1 Package does not contain probe (wire).2P Male XH2.54mm Pitch Wire Cable can be used as a probe,which can be purchased separately or prepared by yourself. 2 For safety, use an DC power supply with good isolation
Application Home water tower automatic water supply system Aquarium Fish tank Water Changer System Fill the water tower automatically Automatic pumping from water tower Conductive liquid automatic control Automatic feeding system for poultry and livestock Farm automatic water supply system And other occasions that require automatic water supply and water exchange. Solenoid valve water pump motor automatic control Interface description: HIGH : Upper limit probe LOW : Lower limit probe DC : Power of positive DC- : Power of negative NC : Relay normally closed contact COM : Relay common contact NO : Relay normally open contact Working principle(Fill the water tower automatically): The water level rises: When the water level is lower than the ''Low level'', the water pump starts to supply water to the water tower; when the water level is higher than the ''High level'', the water pump stops supplying water. Water level reduction: When the water level is lower than the ''High level'', the water pump does not work and the water level continues to decrease. When the water level is lower than the ''Low water level'', the water pump starts to supply water to the water tower. Working principle(Automatic pumping from water tower): Contrary to ''Fill the water tower automatically'' Make the probe(Need to be purchased separately): 1 Prepare 2PCS(or more) XH2.54MM wires (You can prepare this kind of wire by yourself, or buy it from our shop) 2 Multiple wires can be spliced to lengthen the probe length. (Please do waterproof treatment at the splicing.) 3 Please cut the female interface short and keep a distance of 5-10MM (This prevents water droplets from sticking to the probe. )
A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra!
Product Name: DC 12V Fish tank Aquarium automatic supply controller Water Level Sensor Solenoid High Mid Low level LED indicator Board
Package inlcuded: 1 x DC 12V LOW MID HIGH indicators LC66C01 Automatic pumping and pouring controller Module(The probe is 2P Male XH2.54mm Pitch Wire Cable, which can be purchased separately or prepared by yourself.)
Description: 1 Working voltage: DC 12V 2 Standby current 6MA 3 Working current 32MA 4 Size: 63mm X 29mm X 19mm 5 Weight: 20 g 6 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC There are two purposes for connecting the NO and NC ports of the relay: The water pump is connected to the COM NC port to automatically fill the water tower The water pump is connected to the COM NO port to automatically pump water from the water tower Note: 1 Package does not contain probe (wire).2P Male XH2.54mm Pitch Wire Cable can be used as a probe,which can be purchased separately or prepared by yourself. 2 For safety, use an DC power supply with good isolation
Application Home water tower automatic water supply system Aquarium Fish tank Water Changer System Fill the water tower automatically Automatic pumping from water tower Conductive liquid automatic control Automatic feeding system for poultry and livestock Farm automatic water supply system And other occasions that require automatic water supply and water exchange. Solenoid valve water pump motor automatic control Interface description: HIGH : Upper limit probe LOW : Lower limit probe DC : Power of positive DC- : Power of negative NC : Relay normally closed contact COM : Relay common contact NO : Relay normally open contact Working principle(Fill the water tower automatically): The water level rises: When the water level is lower than the ''Low level'', the water pump starts to supply water to the water tower; when the water level is higher than the ''High level'', the water pump stops supplying water. Water level reduction: When the water level is lower than the ''High level'', the water pump does not work and the water level continues to decrease. When the water level is lower than the ''Low water level'', the water pump starts to supply water to the water tower. Working principle(Automatic pumping from water tower): Contrary to ''Fill the water tower automatically'' Make the probe(Need to be purchased separately): 1 Prepare 2PCS(or more) XH2.54MM wires (You can prepare this kind of wire by yourself, or buy it from our shop) 2 Multiple wires can be spliced to lengthen the probe length. (Please do waterproof treatment at the splicing.) 3 Please cut the female interface short and keep a distance of 5-10MM (This prevents water droplets from sticking to the probe. ) 1005002737435384/1 - shop1525466
Product Name: DC 12V Fish tank Aquarium automatic supply controller Water Level Sensor Solenoid High Mid Low level LED indicator Board
Package inlcuded: 1 x DC 12V LOW MID HIGH indicators LC66C01 Automatic pumping and pouring controller Module(The probe is 2P Male XH2.54mm Pitch Wire Cable, which can be purchased separately or prepared by yourself.)
Description: 1 Working voltage: DC 12V 2 Standby current 6MA 3 Working current 32MA 4 Size: 63mm X 29mm X 19mm 5 Weight: 20 g 6 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC There are two purposes for connecting the NO and NC ports of the relay: The water pump is connected to the COM NC port to automatically fill the water tower The water pump is connected to the COM NO port to automatically pump water from the water tower Note: 1 Package does not contain probe (wire).2P Male XH2.54mm Pitch Wire Cable can be used as a probe,which can be purchased separately or prepared by yourself. 2 For safety, use an DC power supply with good isolation
Application Home water tower automatic water supply system Aquarium Fish tank Water Changer System Fill the water tower automatically Automatic pumping from water tower Conductive liquid automatic control Automatic feeding system for poultry and livestock Farm automatic water supply system And other occasions that require automatic water supply and water exchange. Solenoid valve water pump motor automatic control Interface description: HIGH : Upper limit probe LOW : Lower limit probe DC : Power of positive DC- : Power of negative NC : Relay normally closed contact COM : Relay common contact NO : Relay normally open contact Working principle(Fill the water tower automatically): The water level rises: When the water level is lower than the ''Low level'', the water pump starts to supply water to the water tower; when the water level is higher than the ''High level'', the water pump stops supplying water. Water level reduction: When the water level is lower than the ''High level'', the water pump does not work and the water level continues to decrease. When the water level is lower than the ''Low water level'', the water pump starts to supply water to the water tower. Working principle(Automatic pumping from water tower): Contrary to ''Fill the water tower automatically'' Make the probe(Need to be purchased separately): 1 Prepare 2PCS(or more) XH2.54MM wires (You can prepare this kind of wire by yourself, or buy it from our shop) 2 Multiple wires can be spliced to lengthen the probe length. (Please do waterproof treatment at the splicing.) 3 Please cut the female interface short and keep a distance of 5-10MM (This prevents water droplets from sticking to the probe. )
