- -56%
A TDS Meter V1.0 alkalmas UNO analóg TDS-érzékelőhöz, vízvezetőképesség-érzékelőhöz, folyadékérzékelőhöz,
A TDS Meter V1.0 alkalmas UNO analóg TDS-érzékelőhöz, vízvezetőképesség-érzékelőhöz, folyadékérzékelőhöz,
591 Ft
56% megtakarítás
1 343 Ft
Nincs adó
Product Introduction
The commonly used TDS testing equipment is a TDS pen. Although it is cheap and easy to use, it cannot transmit data to the control system, perform long-term online monitoring, and use special instruments for water quality analysis. Although it can transmit data, the accuracy is also low. High, but the price is very expensive. To this end, we have specially introduced an arduino-compatible TDS sensor, which can be used to measure the TDS value of water after it is connected to the arduino controller.
This product is specially designed for arduinoi, plug and play, easy to use. Wide voltage power supply of 3.3~5.5V and analog signal output of 0~2.3V make this product compatible with 5 and 3.3V control systems and can be easily connected to existing control systems for use. The excitation source for measurement adopts cross signal, which can effectively prevent probe polarization, extend the life of the probe, and increase the stability of the output signal. The DS probe is a waterproof probe that can be immersed in water for long-term measurement.
The product can be applied to water quality measurement in domestic water, hydroponics and other fields. With this sensor, you can easily DIY a TDS detector, easily detect the cleanliness of the water, and check your water quality.
Arduino TDS sensor connection diagram
Technical specifications:
Signal transfer board:
Input voltage: 3.3~5.5V
Output signal: 0~2.3V
Working current: 3~6mA
TDS measurement range: 0~1000ppm
TDS measurement accuracy: ±10% F.S. (25°C)
Size: 42*32mm
Module interface: PH2.0-3P
Electrode interface: XH2.54-2P
TDS probe:
Number of probes: 2
Overall length: 83cm
Connection interface: XH2.54-2P
color: White
Other: Waterproof probe
Delivery list:
TDS signal adapter board*1
Waterproof TDS probe*1
Gravity 3PIN analog sensor cable*1
Note:
The TDS probe cannot be used in water above 55°C.
The TDS probe should not be placed too close to the edge of the container, otherwise it will affect the display.
The TDS probe head and wire are waterproof and can be immersed in water, but the wire interface and the signal adapter board are not waterproof, please pay attention to use.
The commonly used TDS testing equipment is a TDS pen. Although it is cheap and easy to use, it cannot transmit data to the control system, perform long-term online monitoring, and use special instruments for water quality analysis. Although it can transmit data, the accuracy is also low. High, but the price is very expensive. To this end, we have specially introduced an arduino-compatible TDS sensor, which can be used to measure the TDS value of water after it is connected to the arduino controller.
This product is specially designed for arduinoi, plug and play, easy to use. Wide voltage power supply of 3.3~5.5V and analog signal output of 0~2.3V make this product compatible with 5 and 3.3V control systems and can be easily connected to existing control systems for use. The excitation source for measurement adopts cross signal, which can effectively prevent probe polarization, extend the life of the probe, and increase the stability of the output signal. The DS probe is a waterproof probe that can be immersed in water for long-term measurement.
The product can be applied to water quality measurement in domestic water, hydroponics and other fields. With this sensor, you can easily DIY a TDS detector, easily detect the cleanliness of the water, and check your water quality.
Arduino TDS sensor connection diagram
Technical specifications:
Signal transfer board:
Input voltage: 3.3~5.5V
Output signal: 0~2.3V
Working current: 3~6mA
TDS measurement range: 0~1000ppm
TDS measurement accuracy: ±10% F.S. (25°C)
Size: 42*32mm
Module interface: PH2.0-3P
Electrode interface: XH2.54-2P
TDS probe:
Number of probes: 2
Overall length: 83cm
Connection interface: XH2.54-2P
color: White
Other: Waterproof probe
Delivery list:
TDS signal adapter board*1
Waterproof TDS probe*1
Gravity 3PIN analog sensor cable*1
Note:
The TDS probe cannot be used in water above 55°C.
The TDS probe should not be placed too close to the edge of the container, otherwise it will affect the display.
The TDS probe head and wire are waterproof and can be immersed in water, but the wire interface and the signal adapter board are not waterproof, please pay attention to use.
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
