Ramps 1.6 is based on Ramps 1.4 & Ramps 1.5 Optimized by Biqu The structure is almost the same as the Ramps 1.5, the difference is that the Ramps 1.6 has a new 2pin connector, the connection is simpler and more convenient, and it will not be easily burned, more importantly, the Ramps 1.6 has a good heat sink above the MOS tube , to provide a better cooling function. In addition, the Ramps 1.6 has more power than the Ramps 1.5, with a maximum power of up to or 270W, while the Ramps 1.5 can only reach 200W, or less than 200W. 1. It can be extended to LCD and other components. 2. There are heater and fan MOSFET outputs and 3 thermistor interfaces 3,5A Additional Safety and Component Protection Fusion 4. Additional 11A fuse for heating bed control 5. Applied to 5 stepper driver boards 6. The design of the board pin socket can be easily replaced or removed for future design 7. I2C and SPI pins are available for future expansion 8. Servo connectors are used to connect limiters, motors and light-emitting diodes. These connectors are gold plated, rated 3A, and are very compact. 9. When the heater has output, the LED light is on 10. Select 2 motors to connect to Z Prusa Mendell
A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra! Rámpák 1.4/1.5/1.6 bővítő vezérlőpult hűtőbordával frissített rámpák 1.4/1.5 arduino 3D nyomtatókártyához Ramps 1.4/1.5/1.6 Expansion Control Panel with Heatsink Upgraded Ramps 1.4/1.5 for arduino 3D Printer Board Ramps 1.6 is based on Ramps 1.4 & Ramps 1.5 Optimized by Biqu The structure is almost the same as the Ramps 1.5, the difference is that the Ramps 1.6 has a new 2pin connector, the connection is simpler and more convenient, and it will not be easily burned, more importantly, the Ramps 1.6 has a good heat sink above the MOS tube , to provide a better cooling function. In addition, the Ramps 1.6 has more power than the Ramps 1.5, with a maximum power of up to or 270W, while the Ramps 1.5 can only reach 200W, or less than 200W. 1. It can be extended to LCD and other components. 2. There are heater and fan MOSFET outputs and 3 thermistor interfaces 3,5A Additional Safety and Component Protection Fusion 4. Additional 11A fuse for heating bed control 5. Applied to 5 stepper driver boards 6. The design of the board pin socket can be easily replaced or removed for future design 7. I2C and SPI pins are available for future expansion 8. Servo connectors are used to connect limiters, motors and light-emitting diodes. These connectors are gold plated, rated 3A, and are very compact. 9. When the heater has output, the LED light is on 10. Select 2 motors to connect to Z Prusa Mendell 1005004236766844/3 - fullstar
Ramps 1.6 is based on Ramps 1.4 & Ramps 1.5 Optimized by Biqu The structure is almost the same as the Ramps 1.5, the difference is that the Ramps 1.6 has a new 2pin connector, the connection is simpler and more convenient, and it will not be easily burned, more importantly, the Ramps 1.6 has a good heat sink above the MOS tube , to provide a better cooling function. In addition, the Ramps 1.6 has more power than the Ramps 1.5, with a maximum power of up to or 270W, while the Ramps 1.5 can only reach 200W, or less than 200W. 1. It can be extended to LCD and other components. 2. There are heater and fan MOSFET outputs and 3 thermistor interfaces 3,5A Additional Safety and Component Protection Fusion 4. Additional 11A fuse for heating bed control 5. Applied to 5 stepper driver boards 6. The design of the board pin socket can be easily replaced or removed for future design 7. I2C and SPI pins are available for future expansion 8. Servo connectors are used to connect limiters, motors and light-emitting diodes. These connectors are gold plated, rated 3A, and are very compact. 9. When the heater has output, the LED light is on 10. Select 2 motors to connect to Z Prusa Mendell
