- -41%
2S 6.4V LiFePO4Green - 2S 8A Li-ion 7.4v 8.4V 18650 BMS PCM 15A Csúcsáram akkumulátorvédő tábla bms Pcm Li-ion Lipo
2S 6.4V LiFePO4Green - 2S 8A Li-ion 7.4v 8.4V 18650 BMS PCM 15A Csúcsáram akkumulátorvédő tábla bms Pcm Li-ion Lipo
179 Ft
41% megtakarítás
304 Ft
Nincs adó
Features:
1) high-accuracy voltage detection circuit;
2) terminal of the charger using high voltage device;
3) Built-in three-stage over-current detection circuit (over-current 1, over-current 2, or load short circuit);
4) MOS transistor can control the battery charge and discharge;
5) low standby current consumption.
Parameter:
Over-charge voltage
4.25~4.35V(±0.05V)
Over-discharge voltage
2.5~3.0V(±0.05V)
Max continuous current
8A
Max peak current
15A
Working temperature
-40℃~ 50℃
Storage Temperature
-40℃~ 80℃
Small current
<3uA
Life cycle
>50000hours
Resistance
<300mΩ
Short cut protection
Protectable,charge can repair
Size
41*16*3.5mm
Note: The lithium battery protection board cannot be used for lithium iron phosphate batteries, hernia lights, hand drill battery packs, electric fish machine battery packs, electric bicycle battery packs, children's car batteries, power motors above 550, and 1W fisheye LEDs. Lamps, please pay attention to customers who purchase the above combination! .
The power range described is applicable to the following products: massager battery pack, LED lamp backup power supply, 12V electronic products, solar street lamp battery pack, monitoring backup power supply, and other products.
Main functions: overcharge protection, over-discharge protection, short circuit protection, overcurrent protection
Wiring instructions:
B is connected to the positive electrode of the battery
B- connect to the negative pole of the battery
MB connects to the connection point between battery 1 and battery 2
P is connected to the positive electrode of the charging/discharging terminal (common to the charging terminal/discharging terminal)
P-Connect the negative electrode of the charge/discharge terminal (common to the charge terminal/discharge terminal)
Reminder: When assembling the battery pack, the battery voltage, capacity, and internal resistance must be paired. The battery voltage is about 3.7V at the rated voltage. After the battery pack is assembled, there is no output. Just charge it with 8.4V.
1) high-accuracy voltage detection circuit;
2) terminal of the charger using high voltage device;
3) Built-in three-stage over-current detection circuit (over-current 1, over-current 2, or load short circuit);
4) MOS transistor can control the battery charge and discharge;
5) low standby current consumption.
Parameter:
Over-charge voltage
4.25~4.35V(±0.05V)
Over-discharge voltage
2.5~3.0V(±0.05V)
Max continuous current
8A
Max peak current
15A
Working temperature
-40℃~ 50℃
Storage Temperature
-40℃~ 80℃
Small current
<3uA
Life cycle
>50000hours
Resistance
<300mΩ
Short cut protection
Protectable,charge can repair
Size
41*16*3.5mm
Note: The lithium battery protection board cannot be used for lithium iron phosphate batteries, hernia lights, hand drill battery packs, electric fish machine battery packs, electric bicycle battery packs, children's car batteries, power motors above 550, and 1W fisheye LEDs. Lamps, please pay attention to customers who purchase the above combination! .
The power range described is applicable to the following products: massager battery pack, LED lamp backup power supply, 12V electronic products, solar street lamp battery pack, monitoring backup power supply, and other products.
Main functions: overcharge protection, over-discharge protection, short circuit protection, overcurrent protection
Wiring instructions:
B is connected to the positive electrode of the battery
B- connect to the negative pole of the battery
MB connects to the connection point between battery 1 and battery 2
P is connected to the positive electrode of the charging/discharging terminal (common to the charging terminal/discharging terminal)
P-Connect the negative electrode of the charge/discharge terminal (common to the charge terminal/discharge terminal)
Reminder: When assembling the battery pack, the battery voltage, capacity, and internal resistance must be paired. The battery voltage is about 3.7V at the rated voltage. After the battery pack is assembled, there is no output. Just charge it with 8.4V.
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
