Szín: 12V - 5V/12V/24V 4-csatornás relémodul árnyékolás ARM PIC AVR DSP elektronikus 5V 4 csatornás relé.4 közúti 5V
248 Ft40% megtakarítás
414 Ft
Nincs adó
Note: We will send according to the voltage you choose to place the order. Don't worry too much about the voltage of the picture and the voltage of the order you placed. Module parameters: 1. Size: 75mm (length) * 55mm (width) * 19.3mm (height) 2. Weight: 61g 3.PCB color: blue 4. There are 4 fixing screw holes around the board, the diameter of the hole is 3.1mm, which is convenient for installation and fixing. 5. The relay uses high-quality relay, single pole double throw. One common end, one normally open end, one normally closed end 6. Optocoupler isolation, good anti-interference 7. Low level pull-in, high level release. The status indicator is on when it is closed, and it is off when it is released. 8. VCC is the system power and JD_VCC is the relay power. 5V relay is issued by default, just plug in the jumper cap 9. Maximum relay output: DC 30V / 10A, AC 250V / 10A Wiring instructions: VCC: system power positive GND: system power negative IN1--IN4: relay control port
A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra! 5V/12V/24V 4-csatornás relémodul árnyékolás ARM PIC AVR DSP elektronikus 5V 4 csatornás relé.4 közúti 5V relé modul 5V/12V/24V 4-Channel Relay Module Shield ARM PIC AVR DSP Electronic 5V 4 Channel Relay.4 road 5V Relay Modul Note: We will send according to the voltage you choose to place the order. Don't worry too much about the voltage of the picture and the voltage of the order you placed. Module parameters: 1. Size: 75mm (length) * 55mm (width) * 19.3mm (height) 2. Weight: 61g 3.PCB color: blue 4. There are 4 fixing screw holes around the board, the diameter of the hole is 3.1mm, which is convenient for installation and fixing. 5. The relay uses high-quality relay, single pole double throw. One common end, one normally open end, one normally closed end 6. Optocoupler isolation, good anti-interference 7. Low level pull-in, high level release. The status indicator is on when it is closed, and it is off when it is released. 8. VCC is the system power and JD_VCC is the relay power. 5V relay is issued by default, just plug in the jumper cap 9. Maximum relay output: DC 30V / 10A, AC 250V / 10A Wiring instructions: VCC: system power positive GND: system power negative IN1--IN4: relay control port 1005001697991718. - miyu
Note: We will send according to the voltage you choose to place the order. Don't worry too much about the voltage of the picture and the voltage of the order you placed. Module parameters: 1. Size: 75mm (length) * 55mm (width) * 19.3mm (height) 2. Weight: 61g 3.PCB color: blue 4. There are 4 fixing screw holes around the board, the diameter of the hole is 3.1mm, which is convenient for installation and fixing. 5. The relay uses high-quality relay, single pole double throw. One common end, one normally open end, one normally closed end 6. Optocoupler isolation, good anti-interference 7. Low level pull-in, high level release. The status indicator is on when it is closed, and it is off when it is released. 8. VCC is the system power and JD_VCC is the relay power. 5V relay is issued by default, just plug in the jumper cap 9. Maximum relay output: DC 30V / 10A, AC 250V / 10A Wiring instructions: VCC: system power positive GND: system power negative IN1--IN4: relay control port