DC 3V-6V bis 400kV 400000V Boost Fokozott teljesítménymodul nagyfeszültségű generátor generátor
192 Ft49% megtakarítás
377 Ft
Nincs adó
This high-voltage module is made using the principle of the Tesla coil. It outputs high-voltage pulsed high-voltage current. It is small in size, high in efficiency, and simple in the peripheral circuit (just connect the switch and the battery). Input voltage: DC 3V-6V Input current: 2A-5A High voltage type: pulse current type Output voltage: about 200,000 volts (please pay attention to safety when using) High voltage two-pole discharge distance: 10mm-20mm Length of output high voltage line: about 100mm Input power cord length: about 100mm (the red wire is positive) Dimensions: Φ24*64mm Regarding the power supply: You can use a single 3.7V lithium battery or two in series, such as 18650 batteries, idle mobile phone batteries (with the protection board removed, the recommended capacity is more than 2000mAh) or Ni-Cd/Ni-MH battery pack, 4V or 6V lead-acid Battery, etc. This module is a finished module of high-voltage inverter transformer/booster for scientific small production. After inputting DC3V-7.2V voltage at the input end, it can get about 200,000 volts DC high voltage at the output end (about 1-2 cm arc) , Note that there is no ignition function
Wiring: The red wire is the positive pole of the power supply. The output is 2 high temperature and high pressure resistant silicone wires
DC 3V-6V bis 400kV 400000V Boost Fokozott teljesítménymodul nagyfeszültségű generátor generátor DC 3V-6V bis 400kV 400000V Boost Step up Power Module High Voltage Generator Generator This high-voltage module is made using the principle of the Tesla coil. It outputs high-voltage pulsed high-voltage current. It is small in size, high in efficiency, and simple in the peripheral circuit (just connect the switch and the battery). Input voltage: DC 3V-6V Input current: 2A-5A High voltage type: pulse current type Output voltage: about 200,000 volts (please pay attention to safety when using) High voltage two-pole discharge distance: 10mm-20mm Length of output high voltage line: about 100mm Input power cord length: about 100mm (the red wire is positive) Dimensions: Φ24*64mm Regarding the power supply: You can use a single 3.7V lithium battery or two in series, such as 18650 batteries, idle mobile phone batteries (with the protection board removed, the recommended capacity is more than 2000mAh) or Ni-Cd/Ni-MH battery pack, 4V or 6V lead-acid Battery, etc. This module is a finished module of high-voltage inverter transformer/booster for scientific small production. After inputting DC3V-7.2V voltage at the input end, it can get about 200,000 volts DC high voltage at the output end (about 1-2 cm arc) , Note that there is no ignition function
Wiring: The red wire is the positive pole of the power supply. The output is 2 high temperature and high pressure resistant silicone wires 1005001658587630. - miyu
This high-voltage module is made using the principle of the Tesla coil. It outputs high-voltage pulsed high-voltage current. It is small in size, high in efficiency, and simple in the peripheral circuit (just connect the switch and the battery). Input voltage: DC 3V-6V Input current: 2A-5A High voltage type: pulse current type Output voltage: about 200,000 volts (please pay attention to safety when using) High voltage two-pole discharge distance: 10mm-20mm Length of output high voltage line: about 100mm Input power cord length: about 100mm (the red wire is positive) Dimensions: Φ24*64mm Regarding the power supply: You can use a single 3.7V lithium battery or two in series, such as 18650 batteries, idle mobile phone batteries (with the protection board removed, the recommended capacity is more than 2000mAh) or Ni-Cd/Ni-MH battery pack, 4V or 6V lead-acid Battery, etc. This module is a finished module of high-voltage inverter transformer/booster for scientific small production. After inputting DC3V-7.2V voltage at the input end, it can get about 200,000 volts DC high voltage at the output end (about 1-2 cm arc) , Note that there is no ignition function
Wiring: The red wire is the positive pole of the power supply. The output is 2 high temperature and high pressure resistant silicone wires