- -41%
FT232RL USB soros adapter USB soros USB TTL 1,8 V 3,3 V
FT232RL USB soros adapter USB soros USB TTL 1,8 V 3,3 V
1 425 Ft
41% megtakarítás
2 415 Ft
Nincs adó
This converter is TTL level: no external voltage is required, it directly supports 3.3V, 1.8V and 5V (other desired level voltages can also be input externally, such as 2.5V 2.8V 3.0V, etc.)
The converter 6-pin interface signal is defined as the commonly used CTS RTS RXD TXD GND VCC
6-pin connector, all signal levels are 3.3V, 1.8V and 5V, jumper cap selectable
Note: Friends who need to support Arduino download can open the shell and configure it according to the label (requires desoldering resistance)! !
The converter can be configured by adjusting the 0R resistor inside the converter as:
1. Output the DTR signal and share the pin with the CTS signal. At this time, the CTS pin signal is DTR (mainly for Arduino download).
2. It can be directly connected to other types of voltage, such as 2.8V, and the output TTL level is 2.8V (the level selection jumper cap needs to be removed).
In general, it is enough to connect RXD, TXD, and GND three wires, and VCC is not connected when the target board does not need the power supply of the converter.
Test on receipt of goods:
After receiving the goods, please do the test as soon as possible. Self-test method: first short-circuit RXD TXD, then send data to the port through the serial port assistant, RXD will receive the data sent by TXD, and display it in the data receiving area of the serial port assistant . This process is often referred to as loopback testing, or the self-receiving of serial lines. (After purchase, you can ask the customer service for our dedicated serial port test software)
If the test fails, it needs to be reported to the customer service as soon as possible. If the product has been received for more than 7 days, we default the product has passed the test.
Some guests did not do self-test before using it, and then the product was damaged due to improper use. It is not because the product has problems. In this case, we will not bear the consequences. Please be aware of it~
Our products are produced in batches by machine patch, and each product has been strictly tested before leaving the factory. It is impossible for several products to be unusable at the same time, unless the product is damaged due to improper use.
FT232RL is an original imported chip. It adopts the chip of the batch in 2021, WIN8.1 WIN10 64-bit, no pressure, no PID problem! Industrial grade operating temperature: -40°C to 85°C
True 5V/3.3V/2.8V/1.8V CMOS IO, support 1.8V TTL level
Supports baud rates up to 3Mbps
Supports Virtual Com Port (VCP) and Direct (D2XX) drivers
Internal integrated 1024bit EEPROM, support customization
The converter 6-pin interface signal is defined as the commonly used CTS RTS RXD TXD GND VCC
6-pin connector, all signal levels are 3.3V, 1.8V and 5V, jumper cap selectable
Note: Friends who need to support Arduino download can open the shell and configure it according to the label (requires desoldering resistance)! !
The converter can be configured by adjusting the 0R resistor inside the converter as:
1. Output the DTR signal and share the pin with the CTS signal. At this time, the CTS pin signal is DTR (mainly for Arduino download).
2. It can be directly connected to other types of voltage, such as 2.8V, and the output TTL level is 2.8V (the level selection jumper cap needs to be removed).
In general, it is enough to connect RXD, TXD, and GND three wires, and VCC is not connected when the target board does not need the power supply of the converter.
Test on receipt of goods:
After receiving the goods, please do the test as soon as possible. Self-test method: first short-circuit RXD TXD, then send data to the port through the serial port assistant, RXD will receive the data sent by TXD, and display it in the data receiving area of the serial port assistant . This process is often referred to as loopback testing, or the self-receiving of serial lines. (After purchase, you can ask the customer service for our dedicated serial port test software)
If the test fails, it needs to be reported to the customer service as soon as possible. If the product has been received for more than 7 days, we default the product has passed the test.
Some guests did not do self-test before using it, and then the product was damaged due to improper use. It is not because the product has problems. In this case, we will not bear the consequences. Please be aware of it~
Our products are produced in batches by machine patch, and each product has been strictly tested before leaving the factory. It is impossible for several products to be unusable at the same time, unless the product is damaged due to improper use.
FT232RL is an original imported chip. It adopts the chip of the batch in 2021, WIN8.1 WIN10 64-bit, no pressure, no PID problem! Industrial grade operating temperature: -40°C to 85°C
True 5V/3.3V/2.8V/1.8V CMOS IO, support 1.8V TTL level
Supports baud rates up to 3Mbps
Supports Virtual Com Port (VCP) and Direct (D2XX) drivers
Internal integrated 1024bit EEPROM, support customization
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
