- -43%
100db Smart Electronics 5V Micro USB 1A 18650 lítium akkumulátor töltőkártya védő töltő modullal az Arduino
100db Smart Electronics 5V Micro USB 1A 18650 lítium akkumulátor töltőkártya védő töltő modullal az Arduino
2 721 Ft
43% megtakarítás
4 773 Ft
Nincs adó
440
end
Notice: The new tracking number for CHINA Post Ordinary Small Packet Plus can be traced only befor it arrive the airport of your country,please choose China Post Air Mail if you want a full tracking infoThe same product will arrive in 15 to 60 days
Tracking info of China Post Ordinary Small Packet Plus can be check here: www17tracknet/en
Smart Electronics 5V Micro USB 1A 18650 Lithium Battery Charging Board With Protection Charger Module for Arduino Diy Kit
The first time you access the battery, it may no voltage between the output OUT and OUT-, then access 5V voltage charge your energy can activate the protection circuit, and the battery from the B B-, then draw a line on the short open also need recharged to activate the protection circuit Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge
MICRO USB female and next - pads for the power input, access 5V B positive then the lithium battery, B- then negative lithium batteries OUT and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load
Connect the battery to the B B-, inserted into the USB female mobile phone charger, the red light is being charged, the green light to full
The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly
The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly
Disclaimer:
Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery,
And still retains the input voltage wiring pads, can be very convenient DIY
Input voltage: 5V
Charging cut-off voltage: 42V ± 1%
Maximum charge current: 1000mA
Battery over-discharge protection voltage: 25V
Battery overcurrent protection current: 3A
Board size: 26 * 17CM
Package Included:
100PCS x18650 Lithium Battery Charging Board
end
Notice: The new tracking number for CHINA Post Ordinary Small Packet Plus can be traced only befor it arrive the airport of your country,please choose China Post Air Mail if you want a full tracking infoThe same product will arrive in 15 to 60 days
Tracking info of China Post Ordinary Small Packet Plus can be check here: www17tracknet/en
Smart Electronics 5V Micro USB 1A 18650 Lithium Battery Charging Board With Protection Charger Module for Arduino Diy Kit
The first time you access the battery, it may no voltage between the output OUT and OUT-, then access 5V voltage charge your energy can activate the protection circuit, and the battery from the B B-, then draw a line on the short open also need recharged to activate the protection circuit Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge
MICRO USB female and next - pads for the power input, access 5V B positive then the lithium battery, B- then negative lithium batteries OUT and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load
Connect the battery to the B B-, inserted into the USB female mobile phone charger, the red light is being charged, the green light to full
The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly
The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly
Disclaimer:
Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery,
And still retains the input voltage wiring pads, can be very convenient DIY
Input voltage: 5V
Charging cut-off voltage: 42V ± 1%
Maximum charge current: 1000mA
Battery over-discharge protection voltage: 25V
Battery overcurrent protection current: 3A
Board size: 26 * 17CM
Package Included:
100PCS x18650 Lithium Battery Charging Board
Biztonsági feltételek
Szállításii feltételek
Visszaküldési feltételek
