• -25%

Smart Electronics 1db MQ2 MQ 2 MQ-2 füstcseppfolyósított gyúlékony metángáz érzékelő modul Arduino Diy

Smart Electronics 1db MQ2 MQ 2 MQ-2 füstcseppfolyósított gyúlékony metángáz érzékelő modul Arduino Diy

188 Ft 25% megtakarítás
250 Ft
Nincs adó
Smart Electronics 1pcs MQ2 MQ 2 MQ-2 Smoke Liquefied Flammable Methane Gas Sensor Module for Arduino Diy Starter Kit
 
MQ-2 gas sensor sensitive material used in the clean air low conductivity tin oxide (SnO2) When there is the environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal MQ-2 gas sensor high on gas, propane, hydrogen sensitivity of detection of natural gas and other flammable vapors are also very good This sensor can detect a variety of flammable gas, is a low-cost sensors for a variety of applications 
 
Gas may be used in homes and factories leakage monitoring device suitable for the detection of gas, butane , propane , methane , smoke , etc 
 
Using high-quality dual-panel design, with power indicator and TTL signal output instructions;
The switching signal having a DO (TTL) output and analog output AO ;
TTL output valid signal is low ( Low-level signal when the output light can be directly connected to the microcontroller or relay module )
Analog output voltage with the higher concentration of higher voltage
A gas, natural gas, city gas , smoke better sensitivity
There are four screw holes for easy positioning ;
Has a long life and reliable stability
Rapid response and recovery characteristic
Input voltage : DC5V Power consumption ( current ): 150mA
DO output : TTL digital 0 and 1 ( 01 and 5V)
AO output :01-0 3 V ( relative to pollution ) , the maximum concentration of a voltage of about 4V
Special note: After the sensor is powered , needs to warm up around 20S, measured data was stable , heat sensor is a normal phenomenon , because the internal heating wire , if hot is not normal
VCC: positive power supply (5V)
GND: power supply is negative
DO: TTL switching signal output
AO: analog signal output
Package included:
100% Brand New
1set x  MQ-2       
 
 
 
Mennyiség

 

Biztonsági feltételek

 

Szállításii feltételek

 

Visszaküldési feltételek

Smart Electronics 1pcs MQ2 MQ 2 MQ-2 Smoke Liquefied Flammable Methane Gas Sensor Module for Arduino Diy Starter Kit
 
MQ-2 gas sensor sensitive material used in the clean air low conductivity tin oxide (SnO2) When there is the environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal MQ-2 gas sensor high on gas, propane, hydrogen sensitivity of detection of natural gas and other flammable vapors are also very good This sensor can detect a variety of flammable gas, is a low-cost sensors for a variety of applications 
 
Gas may be used in homes and factories leakage monitoring device suitable for the detection of gas, butane , propane , methane , smoke , etc 
 
Using high-quality dual-panel design, with power indicator and TTL signal output instructions;
The switching signal having a DO (TTL) output and analog output AO ;
TTL output valid signal is low ( Low-level signal when the output light can be directly connected to the microcontroller or relay module )
Analog output voltage with the higher concentration of higher voltage
A gas, natural gas, city gas , smoke better sensitivity
There are four screw holes for easy positioning ;
Has a long life and reliable stability
Rapid response and recovery characteristic
Input voltage : DC5V Power consumption ( current ): 150mA
DO output : TTL digital 0 and 1 ( 01 and 5V)
AO output :01-0 3 V ( relative to pollution ) , the maximum concentration of a voltage of about 4V
Special note: After the sensor is powered , needs to warm up around 20S, measured data was stable , heat sensor is a normal phenomenon , because the internal heating wire , if hot is not normal
VCC: positive power supply (5V)
GND: power supply is negative
DO: TTL switching signal output
AO: analog signal output
Package included:
100% Brand New
1set x  MQ-2       
 
 
 
32715443785 - suq
32715443785

Hasonló kategóriák mint 16 :

Reviews

Write your review

Smart Electronics 1db MQ2 MQ 2 MQ-2 füstcseppfolyósított gyúlékony metángáz érzékelő modul Arduino Diy

Smart Electronics 1pcs MQ2 MQ 2 MQ-2 Smoke Liquefied Flammable Methane Gas Sensor Module for Arduino Diy Starter Kit
 
MQ-2 gas sensor sensitive material used in the clean air low conductivity tin oxide (SnO2) When there is the environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal MQ-2 gas sensor high on gas, propane, hydrogen sensitivity of detection of natural gas and other flammable vapors are also very good This sensor can detect a variety of flammable gas, is a low-cost sensors for a variety of applications 
 
Gas may be used in homes and factories leakage monitoring device suitable for the detection of gas, butane , propane , methane , smoke , etc 
 
Using high-quality dual-panel design, with power indicator and TTL signal output instructions;
The switching signal having a DO (TTL) output and analog output AO ;
TTL output valid signal is low ( Low-level signal when the output light can be directly connected to the microcontroller or relay module )
Analog output voltage with the higher concentration of higher voltage
A gas, natural gas, city gas , smoke better sensitivity
There are four screw holes for easy positioning ;
Has a long life and reliable stability
Rapid response and recovery characteristic
Input voltage : DC5V Power consumption ( current ): 150mA
DO output : TTL digital 0 and 1 ( 01 and 5V)
AO output :01-0 3 V ( relative to pollution ) , the maximum concentration of a voltage of about 4V
Special note: After the sensor is powered , needs to warm up around 20S, measured data was stable , heat sensor is a normal phenomenon , because the internal heating wire , if hot is not normal
VCC: positive power supply (5V)
GND: power supply is negative
DO: TTL switching signal output
AO: analog signal output
Package included:
100% Brand New
1set x  MQ-2       
 
 
 

Write your review