• -40%

Nincs szín - GY MAX4466 Elektromos mikrofonerősítők C8E2 állítható erősítésű modulokkal

Nincs szín - GY MAX4466 Elektromos mikrofonerősítők C8E2 állítható erősítésű modulokkal

184 Ft 40% megtakarítás
307 Ft
Nincs adó
Description:
Description:1.Add an ear to your project with this well-designed electret microphone amplifier.
2.This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on.
3.This breakout is best used for projects such as voice changers, audio recordingmpling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain.
4.Using it is simple: connect GND to ground, VCC to 2.4-5VDC.
The output pin is not designed to drive speakers or anything but the smallest in-ear headphones
5.you'll need an audio amplifier (such as our 3.7W stereo amp) if you want to connect the amp directly
Specification:The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly
as noisy or scratchy as other mic amp breakouts we've tried!
You can set the gain from 25x to 125x. That's down to be about 200mVpp (for normal speaking volume about 6" away) which is good for attaching to something that expects 'line level' input without clipping, or up to about 1Vpp, ideal for reading from a microcontroller ADC. The output is rail-to-rail so if the sounds
gets loud, the output can go up to 5Vpp!
For the best performance, use the "quietest" supply available (on an Arduino, this would be the 3.3V supply). The audio waveform will come out of the OUT pin. The output will have a DC bias of VCC/2 so when its perfectly quiet, the voltage will be a steady VCC/2 volts (it is DC coupled). If the audio equipment you're using requires AC coupled audio, place a 100uF capacitor between the output pin and the input of your device. If you're connecting to an audio amplifier that has differential inputs or includes decoupling capacitors, the 100uF cap is not required.
Color:Purple and Black
Size:As the Pictures Shown
Package Included:1 x MAX4466 Module
Note:1.Please allow 1-3mm differs due to manual measurement.
2.Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding.
Preview:
Mennyiség

 

Biztonsági feltételek

 

Szállításii feltételek

 

Visszaküldési feltételek

A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
GY MAX4466 Electret Microphone Amplifiers With Adjustable Gain Modules C8E2
Description:
Description:1.Add an ear to your project with this well-designed electret microphone amplifier.
2.This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on.
3.This breakout is best used for projects such as voice changers, audio recordingmpling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain.
4.Using it is simple: connect GND to ground, VCC to 2.4-5VDC.
The output pin is not designed to drive speakers or anything but the smallest in-ear headphones
5.you'll need an audio amplifier (such as our 3.7W stereo amp) if you want to connect the amp directly
Specification:The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly
as noisy or scratchy as other mic amp breakouts we've tried!
You can set the gain from 25x to 125x. That's down to be about 200mVpp (for normal speaking volume about 6" away) which is good for attaching to something that expects 'line level' input without clipping, or up to about 1Vpp, ideal for reading from a microcontroller ADC. The output is rail-to-rail so if the sounds
gets loud, the output can go up to 5Vpp!
For the best performance, use the "quietest" supply available (on an Arduino, this would be the 3.3V supply). The audio waveform will come out of the OUT pin. The output will have a DC bias of VCC/2 so when its perfectly quiet, the voltage will be a steady VCC/2 volts (it is DC coupled). If the audio equipment you're using requires AC coupled audio, place a 100uF capacitor between the output pin and the input of your device. If you're connecting to an audio amplifier that has differential inputs or includes decoupling capacitors, the 100uF cap is not required.
Color:Purple and Black
Size:As the Pictures Shown
Package Included:1 x MAX4466 Module
Note:1.Please allow 1-3mm differs due to manual measurement.
2.Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding.
Preview:
274640229865 - urukz (37)
274640229865

Hasonló kategóriák mint 16 :

Reviews

Write your review

Nincs szín - GY MAX4466 Elektromos mikrofonerősítők C8E2 állítható erősítésű modulokkal

Description:
Description:1.Add an ear to your project with this well-designed electret microphone amplifier.
2.This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on.
3.This breakout is best used for projects such as voice changers, audio recordingmpling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain.
4.Using it is simple: connect GND to ground, VCC to 2.4-5VDC.
The output pin is not designed to drive speakers or anything but the smallest in-ear headphones
5.you'll need an audio amplifier (such as our 3.7W stereo amp) if you want to connect the amp directly
Specification:The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly
as noisy or scratchy as other mic amp breakouts we've tried!
You can set the gain from 25x to 125x. That's down to be about 200mVpp (for normal speaking volume about 6" away) which is good for attaching to something that expects 'line level' input without clipping, or up to about 1Vpp, ideal for reading from a microcontroller ADC. The output is rail-to-rail so if the sounds
gets loud, the output can go up to 5Vpp!
For the best performance, use the "quietest" supply available (on an Arduino, this would be the 3.3V supply). The audio waveform will come out of the OUT pin. The output will have a DC bias of VCC/2 so when its perfectly quiet, the voltage will be a steady VCC/2 volts (it is DC coupled). If the audio equipment you're using requires AC coupled audio, place a 100uF capacitor between the output pin and the input of your device. If you're connecting to an audio amplifier that has differential inputs or includes decoupling capacitors, the 100uF cap is not required.
Color:Purple and Black
Size:As the Pictures Shown
Package Included:1 x MAX4466 Module
Note:1.Please allow 1-3mm differs due to manual measurement.
2.Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding.
Preview:

Write your review