A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra!
MAX7219 pontmátrix modul mikrokontroller kijelző modul MCU LED kijelző vezérlő modul Arduino 5V DIY készletekhez 4 az 1-ben piros/zöld
MAX7219 Dot Matrix Module Microcontroller Display Module MCU LED Display Control Module For Arduino 5V DIY Kits 4 in 1 Red/Green
MAX7219 DIY Kits
1 single module can drive the an 8 * 8 dot matrix common cathode
2 the module Operating voltage: 5 v
The Module 3 dimensions: length 3.2 cm X 3.2 cm wide X 1.3 cm high
4 holes with four screws, the diameter of 3 mm
Five modules with input and output interfaces, support for cascading multiple modules
Wiring instructions:
1 on the left block to an input port, the an output port on the right.
2 the When the control of a single module, simple enter the port received a CPU
The When wining 3 modules cascaded output input termination CPU, the input output termination module of the first two modules of the first one, the first two modules of the termination input terminal of the three modules, and so.
The To 51 single example:
VCC 5 v
GND GND
DIN P2.2
CS P2.1
CLK P2.0
 
MAX7219 4 IN 1 Module
A single module can drive a 8x8 dot matrix common cathode
Operating Voltage: 5V
A single module can drive a 8x8 dot matrix common cathode
Operating Voltage: 5V
Dimensions: 12.8X12.8X1.3cm/
Fixing screws with 64 holes with a diameter 3mm
Module with input and output interfaces, support for cascading multiple modules
Quality:1Set
The left side of the module to the input port, the right to an output port
When the control of a single module, simply input port connected to CPU
When a plurality of cascaded modules, input and output termination CPU, an input terminal of the second output end of the first module a module, the first two modules of the input terminal of the three termination modules, and so on...
51 microcontrollers, for example:
VCC 5V
GND GND
DIN P2.2
CS P2.1
CLK P2.0
 
 
MAX7219 Digital Display Control Module
 
MAX7219 is an integrated serial input / output common-cathode display driver, which connects the microprocessor 7-segment digital LED display with 8 digits, you can connect a bar graph display or 64 independent LED. On which includes a B-type BCD encoder chip, multi-channel scanning loop, segment word driver, but also an 8 x 8 static RAM for storing each data. Only one external register is used to set the segment current for each LED.
 
A convenient four-wire serial interface can connect all the general-purpose microprocessor. Each data can be addressed in the update does not need to rewrite all of the display. MAX7219 also allows users to select each data coding or non-coding.
The entire device contains a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is a LED light all the detection mode.
 
Only three IO ports to drive eight digital tube! Digital flicker-free display! Support cascade!
 
PCB plate fixed to the four corners of copper studs, which can effectively prevent a short circuit accident occurs!
 
Digital tube 0.36 inches four one common cathode LED
 
This module is compatible with 5V / 3.3V microcontroller (51 / AVR / STM32 .......)
 
Wiring instructions (in program provides an example, you can access any IO ports, you can modify the port defined in the program):
 
VCC → 5V
 
GND → GND
 
DIN → P00
 
CS → P01
 
CLK → P02
 
NOTES:
 
1.VCC and GND Do not reversed, it would burn chip
 
2.51 MCU P0 port need pull-up resistor, if your device does not have pull-up resistor can be connected to other ports data lines
 
Invoice:
 
1.MAX7219 digital display module 1
 
2. Straight pin 5P
 
3. bent pin 5P
 
 
1005003112063687./2 - supermodule