A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra!
STM32F401 STM32F411 Fejlesztőkártya V3.0 STM32F401CCU6 STM32F411CEU6 STM32F4 Oktatótábla 84Mhz 64KB RAM 256KB ROM
STM32F401 STM32F411 Development Board V3.0 STM32F401CCU6 STM32F411CEU6 STM32F4 Learning Board 84Mhz 64KB RAM 256KB ROM
 
 
STM32F401CCU6 3.0/STM32F411CEU6 3.0 Development Board
STM32F401CCU6 core board V3.0
Freq. 84Mhz  ROM:256KB RAM:64KB
 
STM32F411CEU6  core board V3.0
Freq. 100MHZ  ROM:512KB RAM:128KB
 
Core Board Information
 
Baidu network disk is not recommended to download data, domestic code cloud is fast
 
Gitee code cloud information link: https://gitee.com/WeAct-TC/MiniF4-STM32F4x1.git
 
Github information link: https://github.com/WeActTC/MiniF4-STM32F4x1.git
 
Baidu network disk link: https://pan.baidu.com/s/1vW9H-q9C5n2yVAEp38pw5A
Extract code: gxnx
 
STM32 download and burn part of the tutorial: https://www.weact-tc.cn/2019/11/30/STM32Download/
 
Part of MicroPython tutorial: https://www.weact-tc.cn/2020/01/01/micropython/
 
MicroPython compilation information: https://github.com/WeActTC/WeAct_F411CE.git
 
 
25MHZ high speed crystal oscillator & 32.768Khz 6PF low speed crystal oscillator
V3.0 version began to use lead-free process, the pin header is gold-plated pin header, more environmentally friendly
Flash pads have been reserved and USBDisk && FATFFS routines are provided
WeAct HID FW Bootloader has been burned out of the factory. It is a special factory test version, and hex is not provided.
Support MicroPython programming, provide available MicroPython firmware, see the link for configuration files, but do not provide technical answers!
Support Arduino programming, see Github https://github.com/stm32duino/Arduino_Core_STM32 for details
 Boards with version V1.3 and above have 3 buttons, reset button, BOOT0 button, and user buttons.
How to enter ISP mode
 
    Method 1: Press and hold the BOOT0 button and the reset button under the power-on state, then release the reset button, and release the BOOT0 button after 0.5 seconds
 
    Method 2: Hold down the BOOT0 key when power is off, and release the BOOT0 key 0.5S after power on
 
    DFU mode: just use the data cable to connect to the computer, if there is a problem of unrecognized, you can properly heat the chip (25 ° C), and then re-enter the ISP mode
 
    Serial port mode: use USB to serial port to connect PA9 and PA10 of the core board
 
    Software: STM32CubeProg.
 
WeAct HID FW Bootloader
 
           No need for USB to serial port, no debugger, no computer driver, just a TYPE-C data cable to complete the firmware download
 
For details, see Code Cloud / Soft / WeAct HID FW Bootloader /
 
How to enter HID Bootloader after writing to APP
 
Press and hold the KEY button, click the reset button, LED C13 flashes, release the KEY button to enter
 
1005001798664558./2 - supermodule