Szín: ESP-01 - ESP8266 ESP-01 ESP-01S ESP-07 ESP-12E ESP-12F ESP-32 soros WIFI vezeték nélküli modul vezeték nélküli adó
178 Ft41% megtakarítás
301 Ft
Nincs adó
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
ESP01 SDIO 2.0, SPI, UART 32-pin QFN package Integrated RF switch, balun, 24dBm PA, DCXO, and PMU Integrated RISC processor, on-chip memory and external memory interfaces Integrated /baseband processors Quality of Service management I2S interface for high fidelity audio applications On-chip low-dropout linear regulators for all internal supplies Proprietary spurious-free clock generation architecture Integrated WEP, TKIP, AES, and WAPI engines Solutions
Supports APSD for optimal VoIP applications Patented spurious noise cancellation algorithm for integration in SOC applications Supports Bluetooth co-existence interface Self-calibrated RF to ensure optimal performance under all operating conditions Zero factory tuning No external RF components Specifications
802.11 b/g/n Wi-Fi Direct (P2P), soft-AP Integrated TCP/IP protocol stack Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLLs, regulators, DCXO and power management units 19.5dBm output power in 802.11b mode Power down leakage current of <10uA Integrated low power 32-bit CPU could be used as application processor SDIO 1.1/2.0, SPI, UART STBC, 1×1 MIMO, 2×1 MIMO A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3)
1. High quality & low price 2. LWIP agreement 3. Support 3 modes: AP, STA, AP STA 4. Perfect and simple AT commands
Now for Arduino can get on WiFI without braking the bank. Use this module for your next Interet of Things project, home automation, Or remote sensor project. This module adats the ESP8226 IC for use over a serial connection using simple AT commands. No SPI interface or Know-How is required.
Warnings: This module requires a 3.3 volt supply for VCC, and 3.3V logic. It is not 5V tolant. Connect RX or TX on 5V for Arduino will destroy this module. You must use a logic level converter, or a 3.3V for Arduino The 3.3V supply on the for Arduino Uno has inadequate current capabilit to power this module. You must provide a separate, higher 3.3V supply(about 300mA or better)
ESP-07 Model:ESP8266 ISM 2.4GHz PA 25dBm 802.11b/g/n Warnings: 1.This module requires a 3.3 volt supply for VCC, and 3.3V logic. 2.It is not 5V tolant,Connect RX or TX on 5V FOR Arduino will destroy this module. 3.You must use a logic level converter, or a 3.3V FOR Arduino 4.The 3.3V supply on the FOR Arduino Uno has inadequate current capabilit to power this module. 5.You must provide a separate,higher 3.3V supply(about 300mA or better)
ESP-12F ESP8266-12F is an enhanced version of ESP8266-12, perfect peripheral circuit, four-layer board technology, enhanced impedance matching, better signal output, whether it is stability or anti-jamming capability, PCB antenna through professional laboratory testing, ROHS certification , Have been greatly improved! For those who choose ESP-12 before, even if the product has been made it does not matter, enhanced version is fully compatible with the firmware before the pin in the ESP-12 on the basis of the addition of six IO port, SPI port leads, the development more convenient, More extensive! Standards Certification: FCC / CE / TELEC Wireless standards: 802.11 b / g / n Frequency range: 2.4GHz-2.5GHz (2400M-2483.5M) Data interface: UART / HSPI / I2C / I2S / Ir Remote Contorl GPIO / PWM Operating voltage: 3.0 ~ 3.6V (recommendation 3.3V) Working Current: Average: 80mA Operating temperature: -40 ° ~ 125 ° Storage temperature: Nomal temperature
ESP-12E Model:ESP8266-12 ISM 2.4GHz PA 25dBm 802.11b/g/n Warnings:
1.This module requires a 3.3 volt supply for VCC, and 3.3V logic.
2.It is not 5V tolant,Connect RX or TX on 5V FOR Arduino will destroy this module.
3.You must use a logic level converter, or a 3.3V FOR Arduino
4.The 3.3V supply on the FOR Arduino Uno has inadequate current capabilit to power this module.
5.You must provide a separate,higher 3.3V supply(about 300mA or better)
A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra! ESP8266 ESP-01 ESP-01S ESP-07 ESP-12E ESP-12F ESP-32 soros WIFI vezeték nélküli modul vezeték nélküli adó-vevő 2.4G ESP8266 ESP-01 ESP-01S ESP-07 ESP-12E ESP-12F ESP-32 serial WIFI wireless module wireless transceiver 2.4G
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
ESP01 SDIO 2.0, SPI, UART 32-pin QFN package Integrated RF switch, balun, 24dBm PA, DCXO, and PMU Integrated RISC processor, on-chip memory and external memory interfaces Integrated /baseband processors Quality of Service management I2S interface for high fidelity audio applications On-chip low-dropout linear regulators for all internal supplies Proprietary spurious-free clock generation architecture Integrated WEP, TKIP, AES, and WAPI engines Solutions
Supports APSD for optimal VoIP applications Patented spurious noise cancellation algorithm for integration in SOC applications Supports Bluetooth co-existence interface Self-calibrated RF to ensure optimal performance under all operating conditions Zero factory tuning No external RF components Specifications
802.11 b/g/n Wi-Fi Direct (P2P), soft-AP Integrated TCP/IP protocol stack Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLLs, regulators, DCXO and power management units 19.5dBm output power in 802.11b mode Power down leakage current of <10uA Integrated low power 32-bit CPU could be used as application processor SDIO 1.1/2.0, SPI, UART STBC, 1×1 MIMO, 2×1 MIMO A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3)
1. High quality & low price 2. LWIP agreement 3. Support 3 modes: AP, STA, AP STA 4. Perfect and simple AT commands
Now for Arduino can get on WiFI without braking the bank. Use this module for your next Interet of Things project, home automation, Or remote sensor project. This module adats the ESP8226 IC for use over a serial connection using simple AT commands. No SPI interface or Know-How is required.
Warnings: This module requires a 3.3 volt supply for VCC, and 3.3V logic. It is not 5V tolant. Connect RX or TX on 5V for Arduino will destroy this module. You must use a logic level converter, or a 3.3V for Arduino The 3.3V supply on the for Arduino Uno has inadequate current capabilit to power this module. You must provide a separate, higher 3.3V supply(about 300mA or better)
ESP-07 Model:ESP8266 ISM 2.4GHz PA 25dBm 802.11b/g/n Warnings: 1.This module requires a 3.3 volt supply for VCC, and 3.3V logic. 2.It is not 5V tolant,Connect RX or TX on 5V FOR Arduino will destroy this module. 3.You must use a logic level converter, or a 3.3V FOR Arduino 4.The 3.3V supply on the FOR Arduino Uno has inadequate current capabilit to power this module. 5.You must provide a separate,higher 3.3V supply(about 300mA or better)
ESP-12F ESP8266-12F is an enhanced version of ESP8266-12, perfect peripheral circuit, four-layer board technology, enhanced impedance matching, better signal output, whether it is stability or anti-jamming capability, PCB antenna through professional laboratory testing, ROHS certification , Have been greatly improved! For those who choose ESP-12 before, even if the product has been made it does not matter, enhanced version is fully compatible with the firmware before the pin in the ESP-12 on the basis of the addition of six IO port, SPI port leads, the development more convenient, More extensive! Standards Certification: FCC / CE / TELEC Wireless standards: 802.11 b / g / n Frequency range: 2.4GHz-2.5GHz (2400M-2483.5M) Data interface: UART / HSPI / I2C / I2S / Ir Remote Contorl GPIO / PWM Operating voltage: 3.0 ~ 3.6V (recommendation 3.3V) Working Current: Average: 80mA Operating temperature: -40 ° ~ 125 ° Storage temperature: Nomal temperature
ESP-12E Model:ESP8266-12 ISM 2.4GHz PA 25dBm 802.11b/g/n Warnings:
1.This module requires a 3.3 volt supply for VCC, and 3.3V logic.
2.It is not 5V tolant,Connect RX or TX on 5V FOR Arduino will destroy this module.
3.You must use a logic level converter, or a 3.3V FOR Arduino
4.The 3.3V supply on the FOR Arduino Uno has inadequate current capabilit to power this module.
5.You must provide a separate,higher 3.3V supply(about 300mA or better)
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
ESP01 SDIO 2.0, SPI, UART 32-pin QFN package Integrated RF switch, balun, 24dBm PA, DCXO, and PMU Integrated RISC processor, on-chip memory and external memory interfaces Integrated /baseband processors Quality of Service management I2S interface for high fidelity audio applications On-chip low-dropout linear regulators for all internal supplies Proprietary spurious-free clock generation architecture Integrated WEP, TKIP, AES, and WAPI engines Solutions
Supports APSD for optimal VoIP applications Patented spurious noise cancellation algorithm for integration in SOC applications Supports Bluetooth co-existence interface Self-calibrated RF to ensure optimal performance under all operating conditions Zero factory tuning No external RF components Specifications
802.11 b/g/n Wi-Fi Direct (P2P), soft-AP Integrated TCP/IP protocol stack Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLLs, regulators, DCXO and power management units 19.5dBm output power in 802.11b mode Power down leakage current of <10uA Integrated low power 32-bit CPU could be used as application processor SDIO 1.1/2.0, SPI, UART STBC, 1×1 MIMO, 2×1 MIMO A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3)
1. High quality & low price 2. LWIP agreement 3. Support 3 modes: AP, STA, AP STA 4. Perfect and simple AT commands
Now for Arduino can get on WiFI without braking the bank. Use this module for your next Interet of Things project, home automation, Or remote sensor project. This module adats the ESP8226 IC for use over a serial connection using simple AT commands. No SPI interface or Know-How is required.
Warnings: This module requires a 3.3 volt supply for VCC, and 3.3V logic. It is not 5V tolant. Connect RX or TX on 5V for Arduino will destroy this module. You must use a logic level converter, or a 3.3V for Arduino The 3.3V supply on the for Arduino Uno has inadequate current capabilit to power this module. You must provide a separate, higher 3.3V supply(about 300mA or better)
ESP-07 Model:ESP8266 ISM 2.4GHz PA 25dBm 802.11b/g/n Warnings: 1.This module requires a 3.3 volt supply for VCC, and 3.3V logic. 2.It is not 5V tolant,Connect RX or TX on 5V FOR Arduino will destroy this module. 3.You must use a logic level converter, or a 3.3V FOR Arduino 4.The 3.3V supply on the FOR Arduino Uno has inadequate current capabilit to power this module. 5.You must provide a separate,higher 3.3V supply(about 300mA or better)
ESP-12F ESP8266-12F is an enhanced version of ESP8266-12, perfect peripheral circuit, four-layer board technology, enhanced impedance matching, better signal output, whether it is stability or anti-jamming capability, PCB antenna through professional laboratory testing, ROHS certification , Have been greatly improved! For those who choose ESP-12 before, even if the product has been made it does not matter, enhanced version is fully compatible with the firmware before the pin in the ESP-12 on the basis of the addition of six IO port, SPI port leads, the development more convenient, More extensive! Standards Certification: FCC / CE / TELEC Wireless standards: 802.11 b / g / n Frequency range: 2.4GHz-2.5GHz (2400M-2483.5M) Data interface: UART / HSPI / I2C / I2S / Ir Remote Contorl GPIO / PWM Operating voltage: 3.0 ~ 3.6V (recommendation 3.3V) Working Current: Average: 80mA Operating temperature: -40 ° ~ 125 ° Storage temperature: Nomal temperature
ESP-12E Model:ESP8266-12 ISM 2.4GHz PA 25dBm 802.11b/g/n Warnings:
1.This module requires a 3.3 volt supply for VCC, and 3.3V logic.
2.It is not 5V tolant,Connect RX or TX on 5V FOR Arduino will destroy this module.
3.You must use a logic level converter, or a 3.3V FOR Arduino
4.The 3.3V supply on the FOR Arduino Uno has inadequate current capabilit to power this module.
5.You must provide a separate,higher 3.3V supply(about 300mA or better)
