• -40%

Nincs szín - Digitális tranzisztor tesztelő SMD alkatrészek teszter dióda triódás ellenállás

Nincs szín - Digitális tranzisztor tesztelő SMD alkatrészek teszter dióda triódás ellenállás

2 404 Ft 40% megtakarítás
4 007 Ft
Nincs adó
Digital Transistor Tester SMD Components Tester Diode Triode Resistance
Product features:
100% brand new and high quality
Made of high-quality materials, durable
This meter is a small tool for engineers, electronic repairs and factories.
It is very easy to test plug-in and SMD devices.It can also test different types of diodes, triodes, thyristors, MOSFETs, so as to be able to analyze device types, pin polarity, output HFE, valve voltage, and FET junction capacitance.
Product parameters:
Resistance: 0-50M ohm Resolution: 0.01 ohm
Capacitance: 25pF-100mF Resolution: 1pF
Inductor: 0.01mH-20H Resolution: 0.01mH
Capacitance ESR: 2uF-50mF Resolution: 0.01 ohm
SMD test clamp probe:
Clip opening distance: 10mm
Maximum voltage: 250V
Product length: about 17cm
Cord length: about 43cm
Package size (LxWxH): 17.50 x 10.00 x 6.00 cm / 6.89 x 3.94 x 2.36 inches
Precautions:
Before testing the capacitor, make sure to discharge it, otherwise the internal circuit may be damaged
If you use a DC power supply, please choose a DC 9V-12V adapter (including 9V and 12V)
It is powered by a 9V 6LR61 battery, when the battery power is lower than 6V, please replace with a new battery.
How to use instructions:
Press "POWER / TEST" to turn on the power and start the test, you can use this button to repeat multiple measurements, and the power will be turned off automatically 20 seconds after the measurement
Provide three kinds of sockets, each socket's pin 1, pin 2 and pin 3 are all connected
There is a table "Typical ESR Values of Electrolytic Capacitors" on the back for reference only. These are the typical values of standard grade electrolytic capacitors at room temperature.
Calibration:
Short the test pins 1, 2, and 3 together, and then press the "POWER / TEST" button, then the screen prompts to enter the calibration, and within 2 seconds press this button again to confirm.
After a few seconds, the screen prompts to release pins 1, 2, and 3, release them and wait for the calibration to complete
Package list:
1 *Digital Transistor Tester
1 *SMD test clamp probe
1 *English user manual
Note:
1. The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. Please allow slight manual measurement deviation for the data.
Mennyiség

 

Biztonsági feltételek

 

Szállításii feltételek

 

Visszaküldési feltételek

A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
Digital Transistor Tester SMD Components Tester Diode Triode Resistance
Product features:
100% brand new and high quality
Made of high-quality materials, durable
This meter is a small tool for engineers, electronic repairs and factories.
It is very easy to test plug-in and SMD devices.It can also test different types of diodes, triodes, thyristors, MOSFETs, so as to be able to analyze device types, pin polarity, output HFE, valve voltage, and FET junction capacitance.
Product parameters:
Resistance: 0-50M ohm Resolution: 0.01 ohm
Capacitance: 25pF-100mF Resolution: 1pF
Inductor: 0.01mH-20H Resolution: 0.01mH
Capacitance ESR: 2uF-50mF Resolution: 0.01 ohm
SMD test clamp probe:
Clip opening distance: 10mm
Maximum voltage: 250V
Product length: about 17cm
Cord length: about 43cm
Package size (LxWxH): 17.50 x 10.00 x 6.00 cm / 6.89 x 3.94 x 2.36 inches
Precautions:
Before testing the capacitor, make sure to discharge it, otherwise the internal circuit may be damaged
If you use a DC power supply, please choose a DC 9V-12V adapter (including 9V and 12V)
It is powered by a 9V 6LR61 battery, when the battery power is lower than 6V, please replace with a new battery.
How to use instructions:
Press "POWER / TEST" to turn on the power and start the test, you can use this button to repeat multiple measurements, and the power will be turned off automatically 20 seconds after the measurement
Provide three kinds of sockets, each socket's pin 1, pin 2 and pin 3 are all connected
There is a table "Typical ESR Values of Electrolytic Capacitors" on the back for reference only. These are the typical values of standard grade electrolytic capacitors at room temperature.
Calibration:
Short the test pins 1, 2, and 3 together, and then press the "POWER / TEST" button, then the screen prompts to enter the calibration, and within 2 seconds press this button again to confirm.
After a few seconds, the screen prompts to release pins 1, 2, and 3, release them and wait for the calibration to complete
Package list:
1 *Digital Transistor Tester
1 *SMD test clamp probe
1 *English user manual
Note:
1. The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. Please allow slight manual measurement deviation for the data.
402525446831 - shoppingtest (27)
402525446831

Hasonló kategóriák mint 16 :

Reviews

Write your review

Nincs szín - Digitális tranzisztor tesztelő SMD alkatrészek teszter dióda triódás ellenállás

Digital Transistor Tester SMD Components Tester Diode Triode Resistance
Product features:
100% brand new and high quality
Made of high-quality materials, durable
This meter is a small tool for engineers, electronic repairs and factories.
It is very easy to test plug-in and SMD devices.It can also test different types of diodes, triodes, thyristors, MOSFETs, so as to be able to analyze device types, pin polarity, output HFE, valve voltage, and FET junction capacitance.
Product parameters:
Resistance: 0-50M ohm Resolution: 0.01 ohm
Capacitance: 25pF-100mF Resolution: 1pF
Inductor: 0.01mH-20H Resolution: 0.01mH
Capacitance ESR: 2uF-50mF Resolution: 0.01 ohm
SMD test clamp probe:
Clip opening distance: 10mm
Maximum voltage: 250V
Product length: about 17cm
Cord length: about 43cm
Package size (LxWxH): 17.50 x 10.00 x 6.00 cm / 6.89 x 3.94 x 2.36 inches
Precautions:
Before testing the capacitor, make sure to discharge it, otherwise the internal circuit may be damaged
If you use a DC power supply, please choose a DC 9V-12V adapter (including 9V and 12V)
It is powered by a 9V 6LR61 battery, when the battery power is lower than 6V, please replace with a new battery.
How to use instructions:
Press "POWER / TEST" to turn on the power and start the test, you can use this button to repeat multiple measurements, and the power will be turned off automatically 20 seconds after the measurement
Provide three kinds of sockets, each socket's pin 1, pin 2 and pin 3 are all connected
There is a table "Typical ESR Values of Electrolytic Capacitors" on the back for reference only. These are the typical values of standard grade electrolytic capacitors at room temperature.
Calibration:
Short the test pins 1, 2, and 3 together, and then press the "POWER / TEST" button, then the screen prompts to enter the calibration, and within 2 seconds press this button again to confirm.
After a few seconds, the screen prompts to release pins 1, 2, and 3, release them and wait for the calibration to complete
Package list:
1 *Digital Transistor Tester
1 *SMD test clamp probe
1 *English user manual
Note:
1. The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2. Please allow slight manual measurement deviation for the data.

Write your review