Szerszám alkatrészek és tartozékok

10pcs 5V Active Alarm Buzzer Beeper 9*5.5mm TMB09A05 5 V Mini Active Piezo Buzzer Fit For Arduino Diy Electronic buzzers 0905

Color: 2Pcs
【Features】
Operating voltage:DC 4.5 ~ 30V
Measure voltage: DC 0 ~ 100V
Minimum resolution(V): 0.1V
Measure current :2A (measure directly,built-in shunt)
Minimum resolution(A): 0.01A
Operating current: <20mA
Display: three 0.28" LED digital tube
Display color: Red and Blue (two-color display)
Dimensions: 48 x 29 x 21mm
Mounting cutout: 45.5 x 26.5mm
Refresh rate: about 500mS / times
Measure accuracy: 1%
Operating temperature: -10 to 65ºc
Operating Humidity: 10 to 80% (non-condensing)
Working pressure: 80 to 106 kPa
【Applications】
Automotive/electric cars/motorcycles battery monitoring or other products voltage current measurement
【Note】
1)The voltage between the thin red and thin black lines must be within DC 4.5-30V
2)The dc amp meter can only be connected to the negative of the device under test
3)10A below ammeter (include 10A), built-in shunt, does not require external shunt
4)When the black thin line vacant, it is better to use insulating tape around the exposed part of the wire, to prevent short circuits
5)If just be used as a voltmeter, it is recommended that the yellow line and the black line were connected together, to prevent the ammeter digital flashing
【Package include】
2x Digital Volt Ampere Meter
4Pcs x Cable

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

(1) Vibration switch module KY-002
(2) Hall magnetic sensor module KY-003
(3) Key switch module for KY-004
(4) Small passive buzzer module for KY-006
(5) Analog temperature sensor module KY-013
(6) Mini magnetic reed module KY-021
(7) Infrared sensor receiving module KY-022
(8) Red Board Flame Sensor Module KY-026
Model: Key switch module for KY-004
1. Rated range Rating: 50mA 12VDC
2. Contact Resistance: 50mΩ max(initial)
3. Insulation Resistance: 100MΩ (minDC 250V)
4. Dielectric Strength: AC250V (50/60Hz for 1minute)
5. Electrical Life: 100,000cycles
Model: Flame Sensor Module KY-026
High sensitivity infrared receiver
Very sensitive to waves between 760-1100nm
Power Indicator
Comparator output indicator
AO, real-time thermal voltage signal output
DO, high/low level signal output
Analog output
Threshold flip level output
Threshold adjustment via potentiometer
Detection angle range: about 60 degrees
Power supply: 0-15 V DC
Hole inner diameter: 3 mm
(Length x Width): 36 x 16 mm
6. Environment temperature: -25℃～ 105℃
7. Operating Force: 180/230(±20gf)
8. Seal temperature: 250℃-280℃

 
1.Included : 100pcs (Four Sizes:35xRed 30xBlue 25xWhite 10xYellow) heat shrink connectors
2.Can be ideal use in marine and automobile applications
3.Polyolefin tubing in outside and hot melt adhesive in inside
4.Solder and seal and with advanced waterproof function
5.Polyolefin heat shrink butt connectors improved pullout strength, provides seal, strain relief, cable check, and insulation
 
Descriptions:
 An easy one step connection of wires, soldered, insulated and sealed
Can be ideal use in marine and automobile applications
Polyolefin tubing in outside and hot melt adhesive in inside
Solder and seal and with advanced waterproof function
Polyolefin heat shrink butt connectors improved pullout strength, provides seal, strain relief, cable check, and insulation
 
 
 
 
 
 
 

 
1.Included : 100pcs (Four Sizes:35xRed 30xBlue 25xWhite 10xYellow) heat shrink connectors
2.Can be ideal use in marine and automobile applications
3.Polyolefin tubing in outside and hot melt adhesive in inside
4.Solder and seal and with advanced waterproof function
5.Polyolefin heat shrink butt connectors improved pullout strength, provides seal, strain relief, cable check, and insulation
 
Descriptions:
 An easy one step connection of wires, soldered, insulated and sealed
Can be ideal use in marine and automobile applications
Polyolefin tubing in outside and hot melt adhesive in inside
Solder and seal and with advanced waterproof function
Polyolefin heat shrink butt connectors improved pullout strength, provides seal, strain relief, cable check, and insulation
 
 
 
 
 
 
 

 
1.Included : 100pcs (Four Sizes:35xRed 30xBlue 25xWhite 10xYellow) heat shrink connectors
2.Can be ideal use in marine and automobile applications
3.Polyolefin tubing in outside and hot melt adhesive in inside
4.Solder and seal and with advanced waterproof function
5.Polyolefin heat shrink butt connectors improved pullout strength, provides seal, strain relief, cable check, and insulation
 
Descriptions:
 An easy one step connection of wires, soldered, insulated and sealed
Can be ideal use in marine and automobile applications
Polyolefin tubing in outside and hot melt adhesive in inside
Solder and seal and with advanced waterproof function
Polyolefin heat shrink butt connectors improved pullout strength, provides seal, strain relief, cable check, and insulation
 
 
 
 
 
 
 

Durable and easy to install
Very convenient and practical
Very popular among the electronic lovers
Package include:
700 x Ceramic Capacitors
35 values (8pF~2.2uF) DIP Multilayer ceramic capacitors Assortment kit 700pcs
No. Capacitance Accuracy Voltage Pin pitch Quantity
1 8RO  8PF ±5% 50V 5.08mm 20pcs
2 22PF 220 ±5% 50V 5.08mm 20pcs
3 30PF 300 ±5% 50V 5.08mm 20pcs
4 33PF 330 ±5% 50V 5.08mm 20pcs
5 82PF 820 ±5% 50V 5.08mm 20pcs
6 100PF 101 ±5% 50V 5.08mm 20pcs
7 220PF 221 ±5% 50V 5.08mm 20pcs
8 330PF 331 ±5% 50V 5.08mm 20pcs
9 470PF 471 ±5% 50V 5.08mm 20pcs
10 680PF 681 ±5% 50V 5.08mm 20pcs
11 820PF 821 ±5% 50V 5.08mm 20pcs
12 1nF  102 ±5% 50V 5.08mm 20pcs
13 1.8nF 182 ±5% 50V 5.08mm 20pcs
14 2.2nF 222 ±5% 50V 5.08mm 20pcs
15 3.3nF 332 ±5% 50V 5.08mm 20pcs
16 4.7nF 472 ±5% 50V 5.08mm 20pcs
17 5.6nF 562 ±5% 50V 5.08mm 20pcs
18 6.8nF 682 ±5% 50V 5.08mm 20pcs
19 8.2nF 822 ±5% 50V 5.08mm 20pcs
20 10nF  103 ±5% 50V 5.08mm 20pcs
21 15nF  153 ±5% 50V 5.08mm 20pcs
22 18nF  183 ±5% 50V 5.08mm 20pcs
23 22nF  223 ±5% 50V 5.08mm 20pcs
24 33nF  333 ±5% 50V 5.08mm 20pcs
25 47nF  473 ±5% 50V 5.08mm 20pcs
26 56nF  563 ±5% 50V 5.08mm 20pcs
27 68nF  683 ±5% 50V 5.08mm 20pcs
28 82nF  823 ±5% 50V 5.08mm 20pcs
29 100nF 104 ±5% 50V 5.08mm 20pcs
30 220nF 224 ±5% 50V 5.08mm 20pcs
31 330nF 334 ±5% 50V 5.08mm 20pcs
32 470nF 474 ±5% 50V 5.08mm 20pcs
33 680nF 684 ±5% 50V 5.08mm 20pcs
34 1uF   105 ±5% 50V 5.08mm 20pcs
35 2.2uF 225 ±5% 50V 5.08mm 20pcs
 

480pcs Monolithic Ceramic Capacitor assortment Kit 10pF-10uF Monolithic Capacitor set 0.1uF 0.22uF 0.47uF 2.2uF 4.7uF Capacitor 
Each   10 pcs ,  all 18 values in one package:
 
10pF(100)   22pF(220)    30pF(300)  47pF(470)  100pF(101)   220pF(221)
 
330pF(331) 470pF(471) 1nF(102)    2.2nF(222) 3.3nF(332)    4.7nF(472)
 
6.8nF(682) 10nF(103)    22nF(223)   47nF(473)  68nF(683)    0.1uF(104)
 
0.22uF(224) 0.47uF(474) 1uF(105)  2.2uF(225)  4.7uF(475)   10uF(106) 

 
Product Description
 Free shipping  FR4 PCB Single Side Copper Clad plate DIY PCB Kit Laminate Circuit Board 10x15cm
Type: Single Sided; Material: FR4 Glass Fiber
 
Surface Finishing: Copper Clad; Color: Copper Tone, Brown
 
 
 
 
 
 
 
 

 
1.product description
Material: Catalpa Alloy Plastic
Rated current: 5A 10A 15A 20A 25A 30A
Rated voltage: 32V
Maximum cut-off current: 50A
Working temperature: -40℃~ 125℃
Box size: 17.5*10*2.5cm
Fuse size: 16.5mm x 11mm x 4mm
Packing: 20pcs×6values a clip
2.product advantages:
①product amper clear amper values for easy use
②transparent plastic housing,convenient quick check
③protects your circuits at all times
3.Adaptation
Great for all tupes of cars and automotive vehicles.
including travel trailer,motorcycles, boats,tour car, and more.
 

4.33*3.54*1.10 inches
 

Diameter: 65MM Thickness: 15MM

Packing: 10 pcs/set
1. Installation type: chassis with screws.
2. The aluminum shell is used for heat dissipation, suitable for cooling plate installation, and can be used in harsh environments.
3. Widely used in ring doorbells, power supplies, sensors, audio, frequency converters, crossovers, elevators, stage audio and automation equipment.
4. The shell is made of aluminum alloy. There are heat radiation grooves on the surface. Good flexibility, multiple choices, suitable for mechanical protection, and more convenient for users to install.
5. Small size, high power. High temperature resistance. Strong overload capacity and strong weather resistance. High precision, low standard induction resistance, high stability, and solid structure.

Durable and easy to install
Very convenient and practical
Very popular among the electronic lovers
Package include:
1300 x 1/4w 130 Values Resistors
1/4w 1% 130 Values Resistors Kit Metal Film Resistor Package Total 1300pcs RoHS 
1ohm-91ohm 42types
1Ω 1.2Ω 1.5Ω 1.8Ω 2Ω
2.2Ω 2.4Ω 2.7Ω 3Ω 3.3Ω
3.6Ω 3.9Ω 4.3Ω 4.7Ω 5.1Ω
5.6Ω 6.2Ω 6.8Ω 7.5Ω 8.2Ω
9.1Ω 10Ω 12Ω 15Ω 18Ω
20Ω 22Ω 24Ω 27Ω 30Ω
33Ω 36Ω 39Ω 43Ω 47Ω
51Ω 56Ω 62Ω 68Ω 75Ω
82Ω 91Ω      
100ohm-2.4K 28typesΩ
100Ω 120Ω 150Ω 180Ω 200Ω
220Ω 240Ω 270Ω 300Ω 330Ω
360Ω 390Ω 430Ω 470Ω 510Ω
560Ω 620Ω 680Ω 750Ω 820Ω
910Ω 1KΩ 1.2KΩ 1.5KΩ 1.8KΩ
2KΩ 2.2KΩ 2.4KΩ    
2.7K-68K 32types
2.7KΩ 3KΩ 3.3KΩ 3.6KΩ 3.9KΩ
4.3KΩ 4.7KΩ 5.1KΩ 5.6KΩ 6.2KΩ
6.8KΩ 7.5KΩ 8.2KΩ 9.1KΩ 10KΩ
12KΩ 15KΩ 18KΩ 20KΩ 22KΩ
24KΩ 27KΩ 30KΩ 33KΩ 36KΩ
39KΩ 43KΩ 47KΩ 51KΩ 56KΩ
62KΩ 68KΩ      
75K-10M 28types
75KΩ 82KΩ 91KΩ 100KΩ 120KΩ
150KΩ 180KΩ 200KΩ 220KΩ 240KΩ
270KΩ 300KΩ 330KΩ 360KΩ 390KΩ
430KΩ 470KΩ 510KΩ 560KΩ 620KΩ
680KΩ 750KΩ 820KΩ 1MΩ 2.2MΩ
3MΩ        
 
 
 
'

(Quantity x Internal Diameter x Single Length)
105pcs x φ1.0 x 40mm(Black)
56pcs x φ2.0 x 40mm (Black)
70pcs x φ3.0 x 45mm(Black)
42pcs x φ4.0 x 45mm (Black)
28pcs x φ5.0 x 65mm (Black)
21pcs x φ6.0 x 65mm(Black)
21pcs x φ8.0 x 90mm (Black)
21pcs x φ10.0 x 90mm(Black)
21pcs x φ12.0 x 90mm(Black) 
Material: PE
Tensile Strength: 10.4 Mpa
Dielectric Strength:15 kV/mm
Minimum Shrinkage Temp: 70°C
Flammability: Flame Retardant
Full Shrinkage Temp: 110°C Maximum
Operating Temperature: -55°C to 125°C
Shrinkage: 2:1 (maximum shrinkage to 1/2 of its supply diameter)