Typical applications:
DC 5V 9V 12V Home lighting system
Garage Door
Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
Wiring Diagram 1:
5.5-12V DC operating voltage DC 5.5-12V devices
Wiring Diagram 2:
5.5-12V DC operating voltage ,DC 1-48V OR AC 85-265V devices
Wiring Diagram 3:
3 5V DC operating voltage ,DC 5 V devices
Wiring Diagram 4:
4 5V DC operating voltage ,DC 1-48V OR AC 85-265V devices
Product Name : Super Mini DC 5V 9V 12V 433.92M 4CH RF Wireless remote control Relay Switch for PT2262 EV1527 Fixed Learning code
Packing list:
1 PCS MINI 433M DC 5V 9V 12V 4 Channel Wireless Controller
1 PCS Plastic shell
1 PCS 2.54MM straight pin
1 PCS 2.54MM curved pin
Compatiable PT2262 EV1527 transmitter , this board can only work with EV1527 encoder or PT2262 encoder.
Features:
1 Operating voltage: Power 1: DC 12V, 9V (range 5.5-15V) ; Power 2: DC 5V
2 Operating current: Standby Current(12V 8MA, 5V 8MA); each relay operating current 40MA
3 Wireless frequency: 433M(315M version can be customized)
4 Receiver sensitivity: -108dBm
5 Decode: learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 6 remote control
6 work mode: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
7 Relay load voltage: DC 1-48V; AC 85-265V
8 Relay load current: <= 2A
9 Size: 49mmx25.5mmx14mm (Very small)
10 Weight: 16g(Very light)
Pin Description:
Vin: Power supply 1 input positive (voltage range: 5.5-15V, recommend 9V 12V)
5V : Power supply 2 Input positive , DC 5V input (Note: power supply 2 can not reverse, otherwise it will burn circuit boards)
gnd: Power supply 1/2 power input ground-
NC1: Channel 1 normally closed contact
CM1: Channel 1 common contact
NO1: Channel 1 normally open contact
NC2: Channel 2 normally closed contact
CM2: Channel 2 common contact
NO2: Channel 2 normally open contact
NC3: Channel 3 normally closed contact
CM3: Channel 3 common contact
NO3: Channel 3 normally open contact
NC4: Channel 4 normally closed contact
CM4: Channel 4 common contact
NO4: Channel 4 normally open contact
Work mode:
There are three Work modes, Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
two pads of T1 connected is Inter-locking (Latch) mode,two pads of T2 connected is Self-locking (Toggle),
All disconnect is Non-locking (Momentary is defult)
Mode Description:
Momentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A; the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;
Toggle : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as BCD. Every Channel is Independent ;
Latch : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2/3/4 is Close.Press transmitter button B, the receiver Channel 2 is Open, the Channel 1/3/4 is Close.
study method:
Clean code: Hold down the learn button down, LED stays on for 4-5 seconds and then turns off
Learning: Hold down the learn button, LED light after release; immediately press the remote control button, LED flashes three times, learning success
Note: The remote control means: EV1527 / PT2262 and compatible remote control
The module is equipped with housing, straight pin and curved needle. You can have a variety of installation
32442752044 - shop1525466
