STM32F401CEU6 core board V3.0 Freq.84MhzROM:64KB RAM:256KB STM32F411CEU6core board V3.0 Freq.100MHZ ROM:128KB RAM:512KB Core Board Information Baidu network disk is not recommended to download data, domestic code cloud is fast Gitee code cloud information link: https://gitee.com/WeAct-TC/MiniF4-STM32F4x1.git Github information link: https://github.com/WeActTC/MiniF4-STM32F4x1.git Baidu network disk link: https://pan.baidu.com/s/1vW9H-q9C5n2yVAEp38pw5A Extract code: gxnx STM32 download and burn part of the tutorial: https://www.weact-tc.cn/2019/11/30/STM32Download/ Part of MicroPython tutorial: https://www.weact-tc.cn/2020/01/01/micropython/ MicroPython compilation information: https://github.com/WeActTC/WeAct_F411CE.git 25MHZ high speed crystal oscillator & 32.768Khz 6PF low speed crystal oscillator V3.0 version began to use lead-free process, the pin header is gold-plated pin header, more environmentally friendly Flash pads have been reserved and USBDisk && FATFFS routines are provided WeAct HID FW Bootloader has been burned out of the factory. It is a special factory test version, and hex is not provided. Support MicroPython programming, provide available MicroPython firmware, see the link for configuration files, but do not provide technical answers! Support Arduino programming, see Github https://github.com/stm32duino/Arduino_Core_STM32 for details Boards with version V1.3 and above have 3 buttons, reset button, BOOT0 button, and user buttons. How to enter ISP mode Method 1: Press and hold the BOOT0 button and the reset button under the power-on state, then release the reset button, and release the BOOT0 button after 0.5 seconds Method 2: Hold down the BOOT0 key when power is off, and release the BOOT0 key 0.5S after power on DFU mode: just use the data cable to connect to the computer, if there is a problem of unrecognized, you can properly heat the chip (25 ° C), and then re-enter the ISP mode Serial port mode: use USB to serial port to connect PA9 and PA10 of the core board Software: STM32CubeProg. WeAct HID FW Bootloader No need for USB to serial port, no debugger, no computer driver, just a TYPE-C data cable to complete the firmware download For details, see Code Cloud / Soft / WeAct HID FW Bootloader / How to enter HID Bootloader after writing to APP Press and hold theKEY button, click thereset button, LED C13flashes, release theKEY buttonto enter
A cím elején, valamint az első képen szereplő szín/minta/méret/típus kerül kiszállításra! STM32F411CE/STM32F401CC alaplap 512K alaplap MicroPython fejlesztőkártya STM32F411CE/STM32F401CC core board 512K core board development board MicroPython STM32F401CEU6 core board V3.0 Freq.84MhzROM:64KB RAM:256KB STM32F411CEU6core board V3.0 Freq.100MHZ ROM:128KB RAM:512KB Core Board Information Baidu network disk is not recommended to download data, domestic code cloud is fast Gitee code cloud information link: https://gitee.com/WeAct-TC/MiniF4-STM32F4x1.git Github information link: https://github.com/WeActTC/MiniF4-STM32F4x1.git Baidu network disk link: https://pan.baidu.com/s/1vW9H-q9C5n2yVAEp38pw5A Extract code: gxnx STM32 download and burn part of the tutorial: https://www.weact-tc.cn/2019/11/30/STM32Download/ Part of MicroPython tutorial: https://www.weact-tc.cn/2020/01/01/micropython/ MicroPython compilation information: https://github.com/WeActTC/WeAct_F411CE.git 25MHZ high speed crystal oscillator & 32.768Khz 6PF low speed crystal oscillator V3.0 version began to use lead-free process, the pin header is gold-plated pin header, more environmentally friendly Flash pads have been reserved and USBDisk && FATFFS routines are provided WeAct HID FW Bootloader has been burned out of the factory. It is a special factory test version, and hex is not provided. Support MicroPython programming, provide available MicroPython firmware, see the link for configuration files, but do not provide technical answers! Support Arduino programming, see Github https://github.com/stm32duino/Arduino_Core_STM32 for details Boards with version V1.3 and above have 3 buttons, reset button, BOOT0 button, and user buttons. How to enter ISP mode Method 1: Press and hold the BOOT0 button and the reset button under the power-on state, then release the reset button, and release the BOOT0 button after 0.5 seconds Method 2: Hold down the BOOT0 key when power is off, and release the BOOT0 key 0.5S after power on DFU mode: just use the data cable to connect to the computer, if there is a problem of unrecognized, you can properly heat the chip (25 ° C), and then re-enter the ISP mode Serial port mode: use USB to serial port to connect PA9 and PA10 of the core board Software: STM32CubeProg. WeAct HID FW Bootloader No need for USB to serial port, no debugger, no computer driver, just a TYPE-C data cable to complete the firmware download For details, see Code Cloud / Soft / WeAct HID FW Bootloader / How to enter HID Bootloader after writing to APP Press and hold theKEY button, click thereset button, LED C13flashes, release theKEY buttonto enter 1005003400838070/2 - fullstar
STM32F401CEU6 core board V3.0 Freq.84MhzROM:64KB RAM:256KB STM32F411CEU6core board V3.0 Freq.100MHZ ROM:128KB RAM:512KB Core Board Information Baidu network disk is not recommended to download data, domestic code cloud is fast Gitee code cloud information link: https://gitee.com/WeAct-TC/MiniF4-STM32F4x1.git Github information link: https://github.com/WeActTC/MiniF4-STM32F4x1.git Baidu network disk link: https://pan.baidu.com/s/1vW9H-q9C5n2yVAEp38pw5A Extract code: gxnx STM32 download and burn part of the tutorial: https://www.weact-tc.cn/2019/11/30/STM32Download/ Part of MicroPython tutorial: https://www.weact-tc.cn/2020/01/01/micropython/ MicroPython compilation information: https://github.com/WeActTC/WeAct_F411CE.git 25MHZ high speed crystal oscillator & 32.768Khz 6PF low speed crystal oscillator V3.0 version began to use lead-free process, the pin header is gold-plated pin header, more environmentally friendly Flash pads have been reserved and USBDisk && FATFFS routines are provided WeAct HID FW Bootloader has been burned out of the factory. It is a special factory test version, and hex is not provided. Support MicroPython programming, provide available MicroPython firmware, see the link for configuration files, but do not provide technical answers! Support Arduino programming, see Github https://github.com/stm32duino/Arduino_Core_STM32 for details Boards with version V1.3 and above have 3 buttons, reset button, BOOT0 button, and user buttons. How to enter ISP mode Method 1: Press and hold the BOOT0 button and the reset button under the power-on state, then release the reset button, and release the BOOT0 button after 0.5 seconds Method 2: Hold down the BOOT0 key when power is off, and release the BOOT0 key 0.5S after power on DFU mode: just use the data cable to connect to the computer, if there is a problem of unrecognized, you can properly heat the chip (25 ° C), and then re-enter the ISP mode Serial port mode: use USB to serial port to connect PA9 and PA10 of the core board Software: STM32CubeProg. WeAct HID FW Bootloader No need for USB to serial port, no debugger, no computer driver, just a TYPE-C data cable to complete the firmware download For details, see Code Cloud / Soft / WeAct HID FW Bootloader / How to enter HID Bootloader after writing to APP Press and hold theKEY button, click thereset button, LED C13flashes, release theKEY buttonto enter
