Kereskedelmi, irodai és ipari

Product Name:Xilinx Platform Cable USB FPGA CPLD SoC Download for XC6SLX9 XC3S500E XC9572XL XC2C64A Spartan-3E SPARTAN 6 Development Board
 
Module No.:  TB300
 
Packing list:
 
1 x Xilinx Platform Cable USB Downloader
1 x 2.54MM pitch adapter plate(Three kinds of interfaces)
1 x 7PIN  2.54MM DuPont wire
1 x 6PIN  2.54MM DuPont wire
1 x 14PIN 2.0mm pitch cable
1 x 14PIN 2.54mm pitch cable
1 x 10PIN 2.54mm pitch cable 
1 x USB2.0 cable
(From left to right)
 
 
 
Description:
 
Performance: 
Using CY7C68013A XC2C256 solution, fully compatible with the original XILINX Platform Cable USB 
Supports all Xilinx devices,FPGA/CPLD/3D IC/Soc/PROM :
XC6SLX9 XC3S500E XC9572XL XC2C64A  
SPARTAN Atrix Kintex Virtex FPGA,XA9500XL XACoolRunner™-II CPLD
Supports JTAG, Slave-Serial and SPI 
Interfaces to devices operating at 5V (TTL), 3.3V (LVCMOS), 2.5V,1.8V and 1.5V 
Selectable target clock frequency, supports software automatic frequency adjustment 
 
Supported Software:
Vivado Design Suite
Xilinx ISE Design Suite  
iMPACT 
ChipScope Pro
 
 
 
 
 
 
 

Product Name:   16-Channel 12VDC Smart Home RS232 Serial COM Controlled Relay Board DB9 UART AT Command Switch Module
    
Package inlcuded: 
1 pcs R223C16  DC 12V 16Ch RS232 Relay Board
  
Description: 
  
1: Working voltage : DC 12V
 
2: Standby current (all relays closed) 18MA, 1 relay open 46MA, 2 relays open 73MA, 3 relays open 100MA,4 relays open 126MA,5 relays open 153MA,6 relays open 179MA, 7 relays open 204MA,8 relays open 230MA…
 
3: ''Open'' ''Close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay''(Only AT command)  ''All Relays Open'' ''All Relays Close'' 8 Commands
 
4: Two kinds of commands: AT command and 8-byte command, the two commands are automatically recognized, no need to switch.
 
5: Under the ''Delay'' command ,the maximum delay is 9999 seconds(Only AT command)
  
6:Output indication : relay output with LED indicators,easy to see working status of the relay;
 
7:Baud rate 9600kbps, 8 data bits, one stop bit, no parity. 
 
8 Size: 172 * 65 * 19mm
9 Weight: 228 g
 
10 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC   
 
    
For more information, please contact me
    
Application
  
Remote control, remote measurement system; 
Wireless meter;
Smart Home,Home Automation ,Wiser Home;
Access control  ;
Identification system  ;
Data collection; 
IT household appliance  ;
Intelligence household appliance;
Baby monitoring system;
LED Motor PLC
PC Remote Control
 
 
Wiring Diagram:
 
1 DC 12V control circuit,Wiring diagram below. ''LOAD'' may be LED lights, fans, motors and   other DC 12V equipment 
 
 
 
 
2 DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). ''LOAD'' may be LED lights, fans, motors and other DC AC equipment
 
 
 
 
 
 
 
 
 
 

Kit No. : RT409
 
 
Qty : 1 pcs PT2262 transmitter module and 4 pcs 4 channels relay switch ;
 
 
Transmitter :
 
 
 
 
 
 
Qty : 1 pcs 15 Button Fixed code remote ;
 
 
 
The super thin large power button 15 remote thin volume, silica gel button design, handle sensitive and numerous keys is very suitable for the kind of need to control many occasions, such as LED light control, sand control, data wireless input, intelligent home comprehensive control and so on, side with switching power supply more energy saving and environmental protection.
Technical parameter:
Working voltage: 12V 23A . 
 
Working current: less than 25mA
Quiescent current: 0mA
Operating frequency: 433MHz .
Chip type: SCT2260 encode IC . 
Shock resistance: 4.7M 
Launch distance: 50-100m (open environment)
Modulation: ASK am
Size: 131.7*53*15.3mm
Weight: 0.065KG
 
Relay receiver :
 
Typical applications:
DC 12V Home lighting system
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lights, fans, motors and other DC 12V
 
 
Wiring Diagram 2:
DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lights, fans, motors and other DC AC equipment
 
 
Wiring Diagram 3:
All kinds of motor reversing control: DC 1-110V or AC 85-265V DC/AC Motor
 
 
 
Product Name : DC 12V 4CH 433MHz Delay RF Wireless Relay Controller For PT2262 EV1527 Encoder
 
Module No.: CE-RF22A04
Packing list:
1 PCS 433M DC 12V 4 Channel Multifunction Wireless Controller
Features:
1 Operating voltage : DC 12V
2 Operating Current: Standby current (all relays closed) 15MA, 1 relay open 42MA, 2 relays open 62MA, 3 relays open 94MA, 4 relays open 121MA
3 Operating frequency: 433.92M;
 
4 Receiver sensitivity : -108dBm
 
5 Decode : learning code, can be adapted EV1527 / PT2262(Click here)and compatible remote control, you can store up to 8 remote control
 
6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; Delay adjustable from 0.1 to 100 seconds, 0.1 seconds Resolution.
7 Size(Including housing)75*54*28mm
8 Weight: 77g
9 Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC
Advantage :
1: Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 OR Pt2262 remotes to re-learn;
 
 
Work mode
Delay mode user guide :
 
1 In delay mode(Mode 3),with a suitable screwdriver and gently rotating adjustable resistance;Clockwise, increasing delay,Counter-clockwise, the delay is reduced
 
2 Delay adjustable from 0.1 to 100 seconds, 0.1 seconds Resolution.
Glossary:
NO : Relay normally open contact
COM : Relay common contact
NC : Relay normally closed contact
Open : NO connection COM, NC disconnect COM
Close : NO disconnect COM, NC connection COM
Momentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A; the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;
Toggle : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as B. Every Channel is Independent ;
Latched : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2 is Close.
Press transmitter button B, the receiver Channel 2 is Open, the Channel 1 is Close.
Delay : Press the Transmitter button A, the receiver Channel 1 is Open,After a set time delay, the receiver Channel 1 is Close, the same as B ,Every Channel is Independent;
If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay Close
 
Adapter remote control (learning remote control):
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
 
 
Clean code: press the button and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
 
 
Step 1 (into the learning mode): Press the button (about 1 second), LED off;
 
Step 2 (adapter channel 1): Then press the first button on the remote control, LED flashes four times off, then learning the first button value
 
Step 3 (Adaptation Channel 2): Then press the second button on the remote control, LED flashes four times brighter, then learned two key values
 
Step 4 (Adaptation Channel 3): Then press the third button on the remote control, LED flashes four times brighter, then learned two key values
 
Step 5 (Adaptation Channel 4): Then press the fourth button on the remote control, LED flashes four times brighter, then learned two key values

Typical applications
1 Motor reversing control circuit,Power supply is DC 12V ,Wiring diagram below. "LOAD" may be DC 1-110V OR 85-265V AC/DC Motor
2 Live wire and Netural wire control circuit,Power supply is DC 12V ,Wiring diagram below. "LOAD" may be AC 85-265V equipment
 
Product Name: 5pcs KC22B02 DC 12V Power on Delay Relay Cycle Timer Switch Board 1-9999s for Motor Reversible Motorcycle
 
 
 
Package inlcuded:
5 PCS KC22B02 DC 12V 2 channel  delay relay module
 
 
 
Description: 
 
DC 12V 2 channels 0-9999 seconds multi-function delay relay board
9 kinds of functions can be switched
Products can set the delay time and Function.After setting up, power-up setting value is previous setting delay time and Function as we set last time  (power-down memory function);
 
Size: 75mm × 35mm x 20mm
Weight : 35.5g
Relay maximum load capacity: DC 1-110V/6A; AC 85-250V/5A
 
 
  
  
User Manua:
 
Noun resolved:
 
COM : Common terminal
 
NO: Normal open
 
NC: Normally Close
 
Relay close: COM connect NO,COM disconnect NC
 
Relay open : COM disconnect NO,COM connect NC
 
Function mode :
 
F1 After power on. Relay 1 close,relay 2 open, delay time is T1. Then relay 1 open,relay 2 is close. Delay time is T2.Relay 1 close, relay 2 open, delay time is T1.Such repeated cycles of action...(for Motor reversing)
 
F2 After power on.Relay 1 close, relay 2 close, delay time is T1. Then relay 1 open, relay 2 is open. Delay time is T2 . Relay 1 close , relay 2 close, delay time is T1. Such repeated cycles of action...
 
F3 After power on . Relay 1 close , delay time is T1. Then relay 1 open , Delay time is T2 . Relay 1 close,delay time is T1. Such repeated cycles of action... ,Relay 2 never work .
 
F4 After power on . Relay 2 open , delay time is T1. Then relay 2 close, Delay time is T2 . Relay 2 close , delay time is T1. Such repeated cycles of action... ,Relay 1 never work .
 
 
F5 After power on . Relay1 and relay 2 close, delay time is T1.Relay1 and relay 2 open (control Live wire and netural wire)
 
 
F6 After power on . Relay 1 close , delay time is T1. Then relay 1 open,Relay 2 never work .
 
F7 After power on . Relay 2 no action, delay time is T1. Then relay 2 close, Relay 1 never work .
 
F8 After power on. Relay 1 and Relay 2 both close, delay time is T1. Then relay 1 open,Delay time is T2, relay 2 open.
 
 
F9 After power on . Relay 1 and Relay 2 both open , delay time is T1. Then relay 1 close, Delay time is T2, relay 2 close.
   
Function Mode Switch:
 
Keep pressing K1, press K2 to switch Function mode
 
F5 F6 F7 mode has only 1 delay time counter (T1), the other mode has two delay time counters (T1 T2); Keep pressing K1 ,press K3, switch T1 T2 counter .
 
   
Adjustment delay time :
 
Press K2, switching 4 bits of delay time counter(0000~9999S),the selected bit flash , press K3 to adjusted counter . Repeat to switch the rest bits .
 
After switching all bits ,then press K2 exit adjustable delay mode; or press K1, exit adjustable delay mode; or wait 10 seconds exit adjustment mode
 
   
Display way :
 
Keep pressing the K3 for 5 seconds , the digital display Turn off. Keep pressing K3 5 second more (or re-power), the digital display Turn on .
 
F5 F6 F7 F8 F9 mode, the delay counter is completed, digital display Turn off, enter a low-power mode, press K1, exit the low-power mode
 

 
Typical applications
1 Motor reversing control circuit,Power supply is DC 5V ,Wiring diagram below. "LOAD" may be DC 1-110V OR 85-265V AC/DC Motor
 
2 Live wire and Netural wire control circuit,Power supply is DC 5V ,Wiring diagram below. "LOAD" may be AC 85-265V equipment
 
 
Product Name: 5pcs DC 5V Digital Dual Programmable Relay Control Cycle Delay Timer Timing Switch LED 
 
 
 
Package inlcuded:
 
5 PCS DC 5V 2 channel cycle delay relay board
 
 
Description: 
 
DC 5V 2 channels 0-9999 seconds multi-function delay relay board
Nine kinds of functions can be switched
Products can set the delay time and Function.After setting up, power-up setting value is previous setting delay time and Function as we set last time  (power-down memory function);
 
Size: 75mm × 35mm x 20mm
Weight : 35g
Relay maximum load capacity: DC 1-110V/6A; AC 85-250V/5A
 
User Manua:
 
Noun resolved:
 
COM : Common terminal
 
NO: Normal open
 
NC: Normally Close
 
Relay close: COM connect NO,COM disconnect NC
 
Relay open : COM disconnect NO,COM connect NC
 
Function mode :
 
F1 After power on. Relay 1 close,relay 2 open, delay time is T1. Then relay 1 open,relay 2 is close. Delay time is T2.Relay 1 close, relay 2 open, delay time is T1.Such repeated cycles of action...(for Motor reversing)
 
F2 After power on.Relay 1 close, relay 2 close, delay time is T1. Then relay 1 open, relay 2 is open. Delay time is T2 . Relay 1 close , relay 2 close, delay time is T1. Such repeated cycles of action...
 
F3 After power on . Relay 1 close , delay time is T1. Then relay 1 open , Delay time is T2 . Relay 1 close,delay time is T1. Such repeated cycles of action... ,Relay 2 never work .
 
F4 After power on . Relay 2 open , delay time is T1. Then relay 2 close, Delay time is T2 . Relay 2 close , delay time is T1. Such repeated cycles of action... ,Relay 1 never work .
 
 
F5 After power on . Relay1 and relay 2 close, delay time is T1.Relay1 and relay 2 open (control Live wire and netural wire)
 
 
F6 After power on . Relay 1 close , delay time is T1. Then relay 1 open,Relay 2 never work .
 
F7 After power on . Relay 2 no action, delay time is T1. Then relay 2 close, Relay 1 never work .
 
F8 After power on. Relay 1 and Relay 2 both close, delay time is T1. Then relay 1 open,Delay time is T2, relay 2 open.
 
 
F9 After power on . Relay 1 and Relay 2 both open , delay time is T1. Then relay 1 close, Delay time is T2, relay 2 close.
   
Function Mode Switch:
 
Keep pressing K1, press K2 to switch Function mode
 
F5 F6 F7 mode has only 1 delay time counter (T1), the other mode has two delay time counters (T1 T2); Keep pressing K1 ,press K3, switch T1 T2 counter .
 
   
Adjustment delay time :
 
Press K2, switching 4 bits of delay time counter(0000~9999S),the selected bit flash , press K3 to adjusted counter . Repeat to switch the rest bits .
 
After switching all bits ,then press K2 exit adjustable delay mode; or press K1, exit adjustable delay mode; or wait 10 seconds exit adjustment mode
 
   
Display way :
 
Keep pressing the K3 for 5 seconds , the digital display Turn off. Keep pressing K3 5 second more (or re-power), the digital display Turn on .
 
F5 F6 F7 F8 F9 mode, the delay counter is completed, digital display Turn off, enter a low-power mode, press K1, exit the low-power mode
 

Below item is powered by eletechsup Ltd .
 
Product Name: 10x Mini 5w 2.6-6v To 3.7v 5v 12v Boost Regulator Module Dc-Dc Boost Converter Module DD0512MA
  
Packing list:
 
10 PCS 6W DD0512MA Ultra-small Ultra-small & Ultra-thin DC-DC Step-up Converter
 
Description:  
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 94% Efficiency (usually is 84% -91% )
 
Quiescent current : 0.19MA.
 
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
 
Size : 13 x 11 x 5.2mm(Ultra small and thin)
Weight : 1g(Ultralight)
 
 
Protection :
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP)
 
Pin description:
 
Pin description:
Vi : Input positive( )
GND : Input and Output negative(GND/-)
Vo : Output positive( )
 
Output 3.7V :
 
Input voltage DC 2.6 ~ 3.6V,output DC 3.7V±3%
Maximum output : 3.7V/1200MA(See the table below for details)
 
Output 5V :
 
Input voltage DC 2.6 ~ 4.5V,output DC 5V±3%
Maximum output : 5V/1200MA(See the table below for details)
 
 
 
Output 12V :
 
Input voltage DC 2.6 ~ 6V,output DC 12V±3%
Maximum output : 12V/500MA(See the table below for details)
 
 
 
 Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router
PLC RS485 devices
Lithium battery power supply equipment
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
 
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
 
 
 
 
 

Below item is powered by eletechsup Ltd .
 
Product Name: 10x Mini 5w 2.6-6v To 3.7v 5v 12v Boost Regulator Module Dc-Dc Boost Converter Module DD0512MA
  
Packing list:
 
10 PCS 6W DD0512MA Ultra-small Ultra-small & Ultra-thin DC-DC Step-up Converter
 
Description:  
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 94% Efficiency (usually is 84% -91% )
 
Quiescent current : 0.19MA.
 
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
 
Size : 13 x 11 x 5.2mm(Ultra small and thin)
Weight : 1g(Ultralight)
 
 
Protection :
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP)
 
Pin description:
 
Pin description:
Vi : Input positive( )
GND : Input and Output negative(GND/-)
Vo : Output positive( )
 
Output 3.7V :
 
Input voltage DC 2.6 ~ 3.6V,output DC 3.7V±3%
Maximum output : 3.7V/1200MA(See the table below for details)
 
Output 5V :
 
Input voltage DC 2.6 ~ 4.5V,output DC 5V±3%
Maximum output : 5V/1200MA(See the table below for details)
 
 
 
Output 12V :
 
Input voltage DC 2.6 ~ 6V,output DC 12V±3%
Maximum output : 12V/500MA(See the table below for details)
 
 
 
 Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router
PLC RS485 devices
Lithium battery power supply equipment
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
 
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
 
 
 
 
 

Below item is powered by eletechsup Ltd .
 
Product Name: 10x Mini 5w 2.6-6v To 3.7v 5v 12v Boost Regulator Module Dc-Dc Boost Converter Module DD0512MA
  
Packing list:
 
10 PCS 6W DD0512MA Ultra-small Ultra-small & Ultra-thin DC-DC Step-up Converter
 
Description:  
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 94% Efficiency (usually is 84% -91% )
 
Quiescent current : 0.19MA.
 
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
 
Size : 13 x 11 x 5.2mm(Ultra small and thin)
Weight : 1g(Ultralight)
 
 
Protection :
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP)
 
Pin description:
 
Pin description:
Vi : Input positive( )
GND : Input and Output negative(GND/-)
Vo : Output positive( )
 
Output 3.7V :
 
Input voltage DC 2.6 ~ 3.6V,output DC 3.7V±3%
Maximum output : 3.7V/1200MA(See the table below for details)
 
Output 5V :
 
Input voltage DC 2.6 ~ 4.5V,output DC 5V±3%
Maximum output : 5V/1200MA(See the table below for details)
 
 
 
Output 12V :
 
Input voltage DC 2.6 ~ 6V,output DC 12V±3%
Maximum output : 12V/500MA(See the table below for details)
 
 
 
 Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router
PLC RS485 devices
Lithium battery power supply equipment
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
 
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
 
 
 
 
 

Product Name:  10pcs MT8870 DTMF Receiver Telephone Dial Tone Decoder Phone Voice Control Module
 
 
Package:(Does not include UNO/MEGA2560):
10 PCS MT8870 DTMF decoder module;
10 PCS Male to Male audio wire (3.5mm jack );
 
Description: 
 
Onboard Complex Frequency Decoder IC MT8870DS 
 
Onboard 5 LED indicators for easy viewing output state 
 
DC Power Supply Voltage:5V(4.5V-5.5V)
 
Operating Temperature : 0- 85 °C
 
IO Drive : Current Maximum 9mA.
 
PCB Size : 25.4x25.4MM
 
This decoding module is for mobile and fixed telephone voice dialing decoding function
Designed specifically for ARDUIUO Board.also use for other MCU(AVR PIC MSP430 STM32 ARM7/9/10/11 FPGA/CPLD)
Does not require any wiring, can be inserted directly into the UNO/MEGA2560/DUE board to use.
12 Digital outputs decode mobile and fixed telephone keys (0-9, * #).Another 4 Digital output(ABCD) can use "DTMF Dial" Software control.
 
uno/mega2560 Code fragment:
After purchase, please contact me for complete code!
//*******************************************//
#include
int STD = A0;
int Q1 = A1;
int Q2 = A2;
int Q3 = A3;
int Q4 = A4;
....
//Check once every 5 ms
void dtmf_decode(void)
{
....
}
void setup()
{
.....
}
void loop()
{
//Complete the decoding
if(Decod_finished)
{
Decod_finished = 0;
Serial.print(" Activate : " );
switch(Q_dat){
case 1 : Serial.print("1 \n" ); break;
case 2 : Serial.print("2 \n" ); break;
case 3 : Serial.print("3 \n" ); break;
case 4 : Serial.print("4 \n" ); break;
case 5 : Serial.print("5 \n" ); break;
case 6 : Serial.print("6 \n" ); break;
case 7 : Serial.print("7 \n" ); break;
case 8 : Serial.print("8 \n" ); break;
case 9 : Serial.print("9 \n" ); break;
case 10 : Serial.print("0 \n" ); break;
case 11 : Serial.print("* \n" ); break;
case 12 : Serial.print("# \n" ); break;
case 13 : Serial.print("A \n" ); break;
case 14 : Serial.print("B \n" ); break;
case 15 : Serial.print("C \n" ); break;
default : Serial.print("D \n" ); break;
}
.....
 
//****************************************************************************//
 
 
Typical application for Mobile phones((Does not include  UNO/MEGA2560):
 
Typical application for DTMF Dial Software:

Below item is powered by eletechsup Ltd . 
 
Product Name:   10x 6W tiny 3V 3.3V 3.7V 4.2V 5V to 12V DC-DC Boost Step up Converter Module
   
Packing list:
  10 PCS 6W mini 2.6-6V to 3.7V 5V 12V Boost Voltage Regulator Module
 
 
 
 
 
Description:  
 
DC DC Boost Converter Module working frequency 1MHZ.
 
Up to 93% Efficiency (usually is 84% -91% )
 
Quiescent current : 0.21MA.
  
Operating temperature range : -40~ 85 Degrees Celsius
 
Storage temperature range : -65~ 150 Degrees Celsius
  
Size : 13 x 11 x 5.2mm(Ultra small & Ultra-thin) 
Weight :  1g(Ultralight)
  
  
Protection : 
 
Over current protection(OCP)
Over voltage protection(OVP)
Short circuit protection(SCP)
Over temperature protection(OTP) 
 
Pin description:
 
Pin description:
Vi       : Input positive( )
GND  : Input and Output negative(GND/-)
Vo      : Output positive( )
 
 
  
 
Output 12V :
  
Input voltage DC 2.6 ~ 6V,output DC 12V±3%
Maximum output : 12V/500MA(See the table below for details)   
  
     
  
  
  Applications
 
Battery powered equipment
Instrumentation, multimeter
Small power motors
PTZ Camera webcam
IP Camera
Toy car boat
Model aircraft
power bank
LED Lighting
WIFI Router 
PLC RS485 devices
Lithium battery power supply equipment
 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 

   
 
 
 
 
 
 

 
 
Product Name: 433M 4 Key HCS301 Rolling Code Keyfob & DC 12V 4CH RKE Secure Remote Keyless Entry System Remote Controller
 
 
 
Package inlcuded(It is recommended to choose to buy a transceiver kit):
1 PCS 433M DC 12V 4CH Rolling Code Relay Module
1 PCS 433M HCS301 Rolling Code Keyfob
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 14MA, 1 relay open 42MA, 2 relays open 69MA, 3 relays open 96MA, 4 relays open 122MA;
3. Wireless Receiving frequency : 433.92M ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. The maximum remote control distance is 30-50 meters
8. size (including shell) 75*54*28mm;
9. weight : 84 grams;
10. Relay Maximum Load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
RKE Secure Remote Keyless Entry system
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Encryption keys are read protected.
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Notice:
This Remote CANNNOT cannot copy or clone any other brand remote , it doesnot have copy function . it can only work with our own rolling code receiver.

 
 
Product Name: 433M 4 Key HCS301 Rolling Code Keyfob & DC 12V 4CH RKE Secure Remote Keyless Entry System Remote Controller
 
 
 
Package inlcuded(It is recommended to choose to buy a transceiver kit):
1 PCS 433M DC 12V 4CH Rolling Code Relay Module
1 PCS 433M HCS301 Rolling Code Keyfob
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 14MA, 1 relay open 42MA, 2 relays open 69MA, 3 relays open 96MA, 4 relays open 122MA;
3. Wireless Receiving frequency : 433.92M ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. The maximum remote control distance is 30-50 meters
8. size (including shell) 75*54*28mm;
9. weight : 84 grams;
10. Relay Maximum Load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
RKE Secure Remote Keyless Entry system
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Encryption keys are read protected.
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Notice:
This Remote CANNNOT cannot copy or clone any other brand remote , it doesnot have copy function . it can only work with our own rolling code receiver.

 
 
Product Name: 433M 4 Key HCS301 Rolling Code Keyfob & DC 12V 4CH RKE Secure Remote Keyless Entry System Remote Controller
 
 
 
Package inlcuded(It is recommended to choose to buy a transceiver kit):
1 PCS 433M DC 12V 4CH Rolling Code Relay Module
1 PCS 433M HCS301 Rolling Code Keyfob
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 14MA, 1 relay open 42MA, 2 relays open 69MA, 3 relays open 96MA, 4 relays open 122MA;
3. Wireless Receiving frequency : 433.92M ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. The maximum remote control distance is 30-50 meters
8. size (including shell) 75*54*28mm;
9. weight : 84 grams;
10. Relay Maximum Load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
RKE Secure Remote Keyless Entry system
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Encryption keys are read protected.
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Notice:
This Remote CANNNOT cannot copy or clone any other brand remote , it doesnot have copy function . it can only work with our own rolling code receiver.

Below item is powered by Canton-Power Ltd.
 
Product Name:  10PCS 1.4A 2.6-6V to 3-15V Adjustable DC-DC Step-Up Current Mode PWM Converter FP6291 Replace XL6009 LM2577
  
Packing list:
 
10 PCS DD06AJSB 2.6V-6V TO 3-15V adjustable Step-up Boost Module
 
  
Description:
   
Input voltage 2.6~6V,output 3~15V adjustable
Maximum input current :  1.4A
Long-term work Current : 1.2A
Conversion efficiency :80-91%
   
DC-DC Boost Converter module working frequency 1.0MHZ. 
Operating ambient temperature : -40~ 85 Degrees Celsius
FPGA/CPLD AVR  Development Board friendly.
 
Size : 20mm x 10.16mm x 5.6mm(Very small)
Weight : about 1.2g(Very light)
 
Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.
 
 
Start Voltage 2.6V, Output Current 10MA
Input  Voltage

Input  Current

Output  Voltage

Output  Curren
2.8V

0.94A

3V

0.7A
2.8V

1.05A

3.3V

0.7A
3V

0.93A

3.26V

0.7A
2.8V

1A

3.72V

0.63A
3V

1.16A

3.7V

0.77A
3.3V

1A

3.7V

0.74A
2.8V

1A

4.5V

0.52A
3V

1.15A

4.52V

0.62A
3.3V

1.2A

4.5V

0.72A
3.7V

1.2A

4.49V

0.83A
2.8V

1A

5.07V

0.46A
3V

1.13A

5.06V

0.55A
3.3V

1.2A

5.04V

0.66A
3.7V

1.23A

5.02V

0.76A
4.5V

1A

5V

0.79A
 
     
2.8V

1A

6.09V

0.38A
3V

1.12A

6.10V

0.46A
3.3V

1.22A

6.08V

0.54A
3.7V

1.22A

6.06V

0.63A
4.5V

1.2A

6.03V

0.78A
5V

1.3A

6.00V

0.95A
2.8V

0.64A

9.11V

0.17A
3V

0.78A

9.12V

0.22A
3.3V

0.98A

9.14V

0.3A
3.7V

1.20A

9.15V

0.41A
4.5V

1.32A

9.16V

0.56A
5V

1.3A

9.15V

0.63A
6V

1.2A

9.11V

0.71A
3V

0.15A

12.15V

0.03A
3.3V

0.51A

12.18V

0.12A
3.7V

0.87A

12.23V

0.23A
4.5V

1.33A

12.16V

0.42A
5V

1.4A

12.16V

0.5A
6V

1.2A

12.17V

0.53A
 
 
Applications
 
MCU Development Board,FPGA/CPLD UNO MEGA2560 DUE 8051 AVR C8051 etc
PLC  RS485 Modbus RTU
9-12V Network equipment/Router
Temperature and humidity sensor
LED Lighting
portable charger
Instruments and meters
5V 6V 9V 12V Relay board
Wireless communication equipment
315M 433M Wireless remote controller
 
Attention :
  
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
 
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
how to use:
With a suitable screwdriver, slowly rotating adjustable resistance
 
 
 

Below item is powered by eletechsup Ltd . 
 
Product Name:   10x 95% 13uA DC DC Boost Converter 0.8-3.3V to 3.3V Step-up Voltage Regulator Power Supply Module
   
Packing list:
 
10 PCS High Efficiency ,synchronous PFM step-up DC-DC converter 0.8-3.3V to 3.3V Module
  
  
Description: 
Input voltage DC 0.8 ~ 3.3V,output DC 3.3V±2%
  
DC DC Boost Converter Module working frequency 350KHZ.
  
High efficiency : 95% (usually is 75% -93% )
  
Low Quiescent Current : 13uA
  
Low ripple and Low noise
    
Ultra-small size : 10.7x10.6x5.6mm
  
Ultra-light weight : 0.65g
  
 
 
Applications
Battery powered equipment
Camera, Video camera
Electric toys
Model aircraft
LED Lighting
STM32 FPGA/CPLD PIC AVR Board
raspberry pi 
electronic diy kit
Wifi Module,ESP8266
Bluetooth Module,HC-05,HC-06,SPP-C
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 
 

 
Typical applications:
DC 12V Home lighting system 
Remote control switch
Smart Home / Home Automation
Garage Door
Fluorescent lamp Illumination
Motorcycle Electromobile
Remote controlled gates
Security Monitoring
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
 
 
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lamp, fans, motors and other DC 12V Electrical equipment
 
 
 
 
Wiring Diagram 2:
DC 1-48V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lamp, fans, motors and other DC AC equipment
 
  
Product Name : Smart Home Kit 433M Wireless remote control Intelligent Remote Delay Relay ON/OFF Switch for LED Fluorescent lamp Illumination
 
Packing list:
4 PCS 433M DC 12V one Channel Delay Switch
1 PCS  433M   Large Power 2 Button EV1527  Remote Control (USE 12V 27A battery,Batteries not included)
 
USE:
  A button on the remote control to control the A controller
  B button on the remote control to control the B controller
  C button on the remote control to control the C controller
  D button on the remote control to control the D controller
  Each controller set up independently,You can form a variety of control methods
 
  
receiver Features:
 
1 Operating voltage:  DC 12V;DC 5V version can be customized
 
2 Operating Current: relays close, about 9MA; relay open,about 42MA;
 
3 Operating frequency: 433.92M; 315M version can be customized                 
 
4 Receiver sensitivity : -108dBm
 
5 Decode  : learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 32 remote control
 
6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch),Delay; 1-5000 seconds adjustable delay time, minimum step 0.1 seconds
 
7 Size(Including housing)50*35*22mm
 
8 Weight(including housing) 30g
 
9 Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC,10A/12VDC
 
 
Work mode
NO          : Relay normally open contact
COM       : Relay common contact
NC          : Relay normally closed contact
Open       : NO connection COM, NC disconnect COM
Close      : NO disconnect COM, NC connection COM
Momentary  : Press the Transmitter button , the receiver relay is Open, release button;the relay  is Close;
Toggle        : Press transmitter button for 1 time , the receiver relay is Open, press button again, the relay  is Close;
Latched       : Press transmitter button A, the receiver relay is Open  Press transmitter button B, the receiver relay is Close.
Delay           : Press the Transmitter button, the receiver relay Open,After a set time delay, the receiver relay  is Close;
 
If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold  the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay Close
 
Adapter remote control (learning remote control):
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
 
Clean code: press the key and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
 
Step 1 (into the learning mode): Press the key (about 1 second), LED off;
Step 2 (adapter button): Then press the utton on the remote control, LED flashes four times on, then learning the button value
 
Note: 
Only the Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch) mode to a "clear code" and " learning " action
 In the "delay" mode can only set the delay time
 
 
Delay setting:
Step 1, the mode is set to "delay" mode (jumper cap on the M1 into two rows of pins)
Step 2, press the key until the LED is off
Step 3. Click the key again, LED flashes
Step 4. Click the key again after a period of time, LED light
LED blinking time is the delay time.
 
 
Power supply : 12V 27A battery  replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current:  ≤ 12mA ;
Oscillation mode:  SAW resonator ;
Oscillation resistor : 330K
Modulation mode: ASK OOK ;
Operating frequency: 433.92MHz  ;
Frequency dev iation: ±0.2MHz ;
Encoding format: Million  Group Code (  EV1527 ) ;
Transmit power: 10 mW.
Data Rate : 50~60KHZ;
  
 
 

Below item is powered by Canton-electronics Ltd .
 
Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.
 
 
 
Modules No: RT389
 
1 pcs Super-Heterodyne decoder receiver and 1 pcs 15 buttons PT2262 encoder transmitter ;
 
 
 
Receiver :
 
Module No.: RF11A04
 
Description:
Model No.: RF11A04 OR CE-RF11A-045V
1. Features:
Operating voltage: DC 3-5V
Operating current: less 11mA (DC 5V)
Working priceple: super heterodyne
modulation Mode: OOK / ASK
Operating Frequency : 433.92MHZ
Receiving sensitivity: -108dBm
Output level: 5V TTL level, low standby, the maximum current 20MA (to add a current-limiting resistor)
Decode: learning code, adapted EV1527 / PT2262 and a compatible remote control, you can store up to eight remote control
Working modes: Non-locking (Momentary ), self-locking (Toggle), Inter-locking; 0.1-500000 seconds adjustable delay time
Size: 30x12.1x12.5mm
Weight: 4 grams or less
 
 
2. Pin Description
G: GND pin, DC 3-5V power supply negative
V: VCC pin, DC 3-5V positive power supply
D0: channel 1 output, active high
D1: channel 2 output, active high
D2: Channel 3 output, active high
D3: Channel 4 output, active high
VT: channel output valid signal, the microcontroller can be used as an interrupt signal
 
3. the working mode
 
You can select different modes of operation with"M4 M3 M2 M1 M0" pad in the delay mode to adjust the delay time through an adjustable resistor.
In delay mode, the rotary variable resistor can adjust the delay time. Increase the time counterclockwise rotation, and clockwise rotation to shorten the time. Adjustable resistor is a precision resistor, adjust the time with a Phillips screwdriver to gently rotate (do not use excessive force)
Working Mode Description:
Non-locking: Press the remote control button, the IO port outputs high. Release the remote control button, IO port outputs low.
Self-locking: Press the remote control button, the IO port outputs high. Press the remote control button again, IO port outputs low.
Interlock: Press the remote control button D0, D0 IO port outputs high, other IO ports outputs low; remote control button is pressed D1, D1 IO port outputs high, other IO ports output low and so on.
Delay: Under Delay mode, there is a delay 0/1/2/3/4 five sub-patterns, by adjusting the variable resistor IO port high duration
4, the adapter remote control (learning remote control)
In normal operation mode, LED (D1) will be lit, when receiving a valid remote control (EV1527 / PT2262) key value, LED will flash.
Clean code: hold the button to press.LED offs, keep pressing about 8 seconds until LED lights. At that time, clean code completion (Note: After the implementation of clean code, previous remote controls do not exist.
Adaptation (learning):
Step 1 (into the learning mode):trigger the key button, LED offs;
Step 2 (adapter channel 1): press the first button of remote control and then, LED offs after flashes for four times. This time means that it had learned the value of the first button
Step 3 (Adaptation Channel 2): Press the second remote control, LED offs after flashes 4 times, This time means that it had learned the value of the second button
Step 4 (adapter Channel 3): Then press the remote's third button, LED offs after flashes 4 times, This time means that it had learned the value of the third button
Step 5 (Adaptation Channel 4): Then press the remote control's fourth button, LED lights after flashes 4 times, This time means that it had learned the value of the fourth button.
NOTE: The process must be completed within 15 seconds
 
Adaptation Video,Click here!
 
5. Wiring Diagram :
Control LED indicator: see "RF11A04_LED demo"
Control 12V Relay: See "RF11A04_4Relay demo"
Click here for more help!
 
 
 
Connect with ardiuno :
 
 
 
 
Transmitter :
 
 
Features / Specifications :
1. 4 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
 
Technical Data :
Transmitter Module No.: TB420;
Power supply : 12V 23A battery (not included )  ,
 
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format: SCT2260  fixed code (compatiable for PT2262 SC2262 PT2260 PT2264 , can work with PT2272-M4 ,PT2272-T4,PT2272-L4 );
RC  Resistance : 4.7M; 
Transmit power : 200mW ;
 
 
Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.

Product Name: 8CH 433M DC 12V Lora Bidirectional Remote IO Controller LED Feedback Indicator NPN In Relay Out Swicth Module Board
Packing list:
1 PCS RTTXA08 Transmitter
1 PCS RTRXB08 Receiver
(It is recommended to buy both transmitter and receiver)
Please contact me for detailed instructions
Description:
 
This is a wireless remote control switch with feedback function, no configuration required, as long as the transceiver ''Frequency and ID'' settings are consistent, it can be controlled. With feedback function, the LED indicator on the transmitter will indicate the switch status of the receiver.
Transmitter :
 
1 Working voltage: DC 12V (8-30V)
2 Working current: 12-30MA
3 Input channels: 8 channels, low pulse trigger (NPN)
4 Transmit power: 22dBm
5 Working frequency band: 425~455MHz (can be set by DIP switch)
6 The farthest transmission distance in the open field: 2 kilometers
7 Size: 115x90x40mm (with shell)
8 Weight: 49 grams (without shell)120 grams (with shell)
Receiver:
1 Working voltage: DC 12V (11-15V)
2 Working current: 12-260MA
3 Output channels: 8 channels 10A relay output
4 Working frequency band: 425~455MHz (can be set by DIP switch)
6 The farthest transmission distance in the open field: 2 kilometers
6 Working mode: Momentary(Jog),Self-locking,Interlock, Delay (can be set by DIP switch)
7 Dimensions: 145x90x40mm (with shell)
8 Weight: 134 grams (without shell),200 grams (with shell)
9 Maximum load: 10A/250VAC, 10A/125VAC, 10A/30VDC, 10A/28VDC, 10A/12VDC
Application:
Smart Home,Home Automation ;
Identification system;
Remote Motor Control System
CCTV Camera PTZ Control;
Security system;
LED dot matrix screen;
Ship remote control system
Farm remote gate control system
 
The first use process:
1 Confirm that the frequency and ID of the receiver and transmitter are the same
2 Power on the receiver first, the PWR light is on
3 Power on the transmitter again, the PWR light flashes, and the PWR light on the receiver flashes at the same time, indicating that the pairing is successful.
4 At this time, the relay on the receiver can be remotely controlled through the input port on the transmitter.
NOTE:
To install the antenna, remove the top cover of the housing
When using two transmitting devices at the same time, the frequency or ID number cannot be the same
When using two receiving devices at the same time, the frequency or ID number cannot be the same

Product Name: 8CH 433M DC 12V Lora Bidirectional Remote IO Controller LED Feedback Indicator NPN In Relay Out Swicth Module Board
Packing list:
1 PCS RTTXA08 Transmitter
1 PCS RTRXB08 Receiver
(It is recommended to buy both transmitter and receiver)
Please contact me for detailed instructions
Description:
 
This is a wireless remote control switch with feedback function, no configuration required, as long as the transceiver ''Frequency and ID'' settings are consistent, it can be controlled. With feedback function, the LED indicator on the transmitter will indicate the switch status of the receiver.
Transmitter :
 
1 Working voltage: DC 12V (8-30V)
2 Working current: 12-30MA
3 Input channels: 8 channels, low pulse trigger (NPN)
4 Transmit power: 22dBm
5 Working frequency band: 425~455MHz (can be set by DIP switch)
6 The farthest transmission distance in the open field: 2 kilometers
7 Size: 115x90x40mm (with shell)
8 Weight: 49 grams (without shell)120 grams (with shell)
Receiver:
1 Working voltage: DC 12V (11-15V)
2 Working current: 12-260MA
3 Output channels: 8 channels 10A relay output
4 Working frequency band: 425~455MHz (can be set by DIP switch)
6 The farthest transmission distance in the open field: 2 kilometers
6 Working mode: Momentary(Jog),Self-locking,Interlock, Delay (can be set by DIP switch)
7 Dimensions: 145x90x40mm (with shell)
8 Weight: 134 grams (without shell),200 grams (with shell)
9 Maximum load: 10A/250VAC, 10A/125VAC, 10A/30VDC, 10A/28VDC, 10A/12VDC
Application:
Smart Home,Home Automation ;
Identification system;
Remote Motor Control System
CCTV Camera PTZ Control;
Security system;
LED dot matrix screen;
Ship remote control system
Farm remote gate control system
 
The first use process:
1 Confirm that the frequency and ID of the receiver and transmitter are the same
2 Power on the receiver first, the PWR light is on
3 Power on the transmitter again, the PWR light flashes, and the PWR light on the receiver flashes at the same time, indicating that the pairing is successful.
4 At this time, the relay on the receiver can be remotely controlled through the input port on the transmitter.
NOTE:
To install the antenna, remove the top cover of the housing
When using two transmitting devices at the same time, the frequency or ID number cannot be the same
When using two receiving devices at the same time, the frequency or ID number cannot be the same

Product Name: 8CH 433M DC 12V Lora Bidirectional Remote IO Controller LED Feedback Indicator NPN In Relay Out Swicth Module Board
Packing list:
1 PCS RTTXA08 Transmitter
1 PCS RTRXB08 Receiver
(It is recommended to buy both transmitter and receiver)
Please contact me for detailed instructions
Description:
 
This is a wireless remote control switch with feedback function, no configuration required, as long as the transceiver ''Frequency and ID'' settings are consistent, it can be controlled. With feedback function, the LED indicator on the transmitter will indicate the switch status of the receiver.
Transmitter :
 
1 Working voltage: DC 12V (8-30V)
2 Working current: 12-30MA
3 Input channels: 8 channels, low pulse trigger (NPN)
4 Transmit power: 22dBm
5 Working frequency band: 425~455MHz (can be set by DIP switch)
6 The farthest transmission distance in the open field: 2 kilometers
7 Size: 115x90x40mm (with shell)
8 Weight: 49 grams (without shell)120 grams (with shell)
Receiver:
1 Working voltage: DC 12V (11-15V)
2 Working current: 12-260MA
3 Output channels: 8 channels 10A relay output
4 Working frequency band: 425~455MHz (can be set by DIP switch)
6 The farthest transmission distance in the open field: 2 kilometers
6 Working mode: Momentary(Jog),Self-locking,Interlock, Delay (can be set by DIP switch)
7 Dimensions: 145x90x40mm (with shell)
8 Weight: 134 grams (without shell),200 grams (with shell)
9 Maximum load: 10A/250VAC, 10A/125VAC, 10A/30VDC, 10A/28VDC, 10A/12VDC
Application:
Smart Home,Home Automation ;
Identification system;
Remote Motor Control System
CCTV Camera PTZ Control;
Security system;
LED dot matrix screen;
Ship remote control system
Farm remote gate control system
 
The first use process:
1 Confirm that the frequency and ID of the receiver and transmitter are the same
2 Power on the receiver first, the PWR light is on
3 Power on the transmitter again, the PWR light flashes, and the PWR light on the receiver flashes at the same time, indicating that the pairing is successful.
4 At this time, the relay on the receiver can be remotely controlled through the input port on the transmitter.
NOTE:
To install the antenna, remove the top cover of the housing
When using two transmitting devices at the same time, the frequency or ID number cannot be the same
When using two receiving devices at the same time, the frequency or ID number cannot be the same

Below item is powered by Canton-Power Ltd . 
 
Product Name:  10pcs DD0606SA_3V3 0.9-3.3V to 3.3V DC/DC Boost Voltage Converter Module PWM PFM Switching Power Supply Board
  
Packing list:
 
10 PCS 1V-3.3V TO 3.3V Step-up Boost Module
 
  
Description:
Input voltage DC 0.9 ~ 3.3V, output DC 3.3V( -5% )
 
DC DC Boost Converter Module working frequency 1MHZ.efficiency 65% -88% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Excluding Pin Size : 21.3mm x 12.5mm x 5.7mm(Very small)
 
Weight : 1.85g(Very light) 
 
 
 Applications
 
Battery powered equipment
Breadboard Power Supply
ARM STM32 FPGA CPLD Board
 Bluetooth Wifi RF Wireless Board,  esp8266 nrf24l01 rtl8710 GSM etc
3.3V Small power motors
Camera, Video camera
3.3V Toy car
PDA
LED Lighting
Wireless communication equipment
Audio equipment 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 

Product Name: MAX II EPM570 CPLD Minimum System Core Board Development Board EPM570T100C5N Replace EPM240 ALTERA PLD FPGA Programmable Logic IC 
 
Module No#:  TB282
 
Packing list:
 
1 pcs EPM570 core Board;
 
Description: 
 
Onboard  EPM570T100C5N chip
 
50Mhz Active crystal
 
All pins from CPLD are Labelled and available onboard
 
Altera Official standards JTAG Interface
 
Two 5V 3#3V output to provide power for the peripheral
 
A Independent button for test core board
 
Two independent LED lights for test core board
 
Size : 9cm X 6cm #9:6 is Golden ratio ^_^#
 

PCB Board 3D View:

Typical applications:
  
Motor Toy car Model aircraft 2A Driver
ARDUIUO UNO MEGA2560 Pro mini DUE
breadboard PCB Universal board
raspberry pi ARM AVR PIC
DC 5V 9V 12V Home lighting system 
Smart Home / Home Automation
LED lighting
12V DC Motor,RS360
 5V DC Motor
 
There are a variety of installation,can for breadboard ,PCB, Universal board,UNO MEGA2560 raspberry pi
 
 
Wiring Diagram 1:
 5.5-12V DC operating voltage DC 5.5-12V devices
 
 
Wiring Diagram 2:
5.5-12V DC operating voltage ,DC 1-48V OR AC 85-265V devices
 
  
Wiring Diagram 3:
3 5V DC operating voltage ,DC 5 V devices
Wiring Diagram 4:
4 5V DC operating voltage ,DC 1-48V OR AC 85-265V devices
 
 
 
 
 
Product Name : DC 5V 6V 9V 12V LED Motor Toy car Model aircraft 2A Driver EV1527 Remote control mini Wireless remote control switch Relay Kit
 
Packing list:
1 PCS MINI 433M DC 5V 9V 12V 4 Channel Wireless Controller 
4 PCS  433M 4 Button EV1527 Remote Control( USE 12V 27A battery,Batteries not included )
1 PCS Plastic shell
1 PCS 2.54MM straight pin
1 PCS 2.54MM curved pin

 
 
Features:
 
1 Operating voltage: Power 1: DC  5V,6V , 9V, 12V (range 5 -15V) ; Power 2: DC 4.2-5V
 
2 Operating current: Standby Current(12V 8MA, 5V 8MA); each relay operating current 40MA
 
3 Wireless frequency: 433M(315M version can be customized)
 
4 Receiver sensitivity: -108dBm
 
5 Decode: learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 6 remote control
 
6 work mode: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
 
7 Relay load voltage: DC 1-48V; AC 85-265V
 
8 Relay load current: <= 2A
 
9 Size: 49mmx25.5mmx14mm (Very small)
 
10 Weight: 16g(Very light)
  
Normally, we would adapter remote control and receiver.
If the item you received has not been adapted Or you need to add accessories, Please follow the instructions below
 
study method:
Clean code: Hold down the learn button down, LED stays on for 4-5 seconds and then turns off
Learning: Hold down the learn button, LED light after release; immediately press the remote control button, LED flashes three times, learning success
 
Use more details, please click here!
 
 
Work mode:
There are three Work modes, Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch)
two pads of T1  connected is Inter-locking (Latch) mode,two pads of T2  connected is Self-locking (Toggle),
All disconnect is Non-locking (Momentary is defult)
  
Mode Description:
Momentary : Press the Transmitter button A, the receiver Channel 1 is Open, release button A, the receiver Channel 1 is Close, the same as B ,Every Channel is Independent ;
Toggle     : Press transmitter button A for 1 time , the receiver Channel 1 is Open, press button A again, the receiver Channel 1 is Close, the same as BCD. Every Channel is Independent ;
Latch      : Press transmitter button A, the receiver Channel 1 is Open, the Channel 2/3/4 is Close.Press transmitter button B, the receiver Channel 2 is Open, the Channel 1/3/4 is Close.
 
 
 
 
433M 4 Button EV1527 Remote Control:
 
Power supply : 12V 27A battery  replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current:  ≤ 12mA ;
Oscillation mode:  SAW resonator ;
Oscillation resistor : 330K
Modulation mode: ASK OOK ;
Operating frequency: 433.92MHz  ;
Frequency dev iation: ±0.2MHz ;
Encoding format: Million  Group Code (  EV1527 ) ;
Transmit power: 10 mW.
Data Rate : 50~60KHZ;
  
 
 
 

Work mode
   
 
 
Typical applications:
DC 12V Home lighting system 
Electric door gate
Garage Door
Elevators
Motor reversing control
Remote control switch
Smart Home Kit
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
 
 
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lights, fans, motors and other DC 12V
 
 
 
 
Wiring Diagram 2:
DC 1-48V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lights, fans, motors and other DC AC equipment
  
Product Name : 6x Transmitter 1x Receiver kit RF 12v time delay relay 433m Wireless control
 
Packing list:
1 PCS 433M DC 12V 2 Channel Multifunction Wireless Controller 
6 PCS  433M   Large Power 2 Button EV1527  Remote Control (USE 12V 27A battery,Batteries not included)
 
 
 
Technical indicators:
Operating voltage : DC 12V;DC 5V version can be customized
Operating Current : All relays close,about 14MA; one relay open,about 43MA;two relay  open,about 71MA
Operating frequency : 433.92M; 315M version can be customized
Receiver sensitivity  : -108dB;
Work mode       : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch),  Delay;Each channel independently set the Work mode; 500,000 seconds maximum delay
 
Size(Including housing)  : 75*54*28mm
Learning function (can works with EV1527 and PT2262 remote, can store 16 pcs different code remote );
Max load : 500W;
  
Normally, we would adapter remote control and receiver.
If the item you received has not been adapted Or you need to add accessories, Please follow the instructions below
Learning method and steps:
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
   
Clean code: press the button and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
     
Step 1 (into the learning mode): Press the button (about 1 second), LED off;
Step 2 (adapter channel 1): Then press the first button on the remote control, LED flashes four times off, then learning the first button value
Step 3 (Adaptation Channel 2): Then press the second button on the remote control, LED flashes four times brighter, then learned two key values
 
Use more details, please click here!
 
 

 
 
433M 2 Button EV1527 Remote Control:
 
Power supply : 12V 27A battery  replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current:  ≤ 12mA ;
Oscillation mode:  SAW resonator ;
Oscillation resistor : 330K
Modulation mode: ASK OOK ;
Operating frequency: 433.92MHz  ;
Frequency dev iation: ±0.2MHz ;
Encoding format: Million  Group Code (  EV1527 ) ;
Transmit power: 10 mW.
Data Rate : 50~60KHZ;
  
 
 
 

it No. : RT395
This  remote switch allows you to remotely  control any 12 Volt DC device.  Perfect for controlling any 12V devices  such as Lights, Fans,  Landscaping Lighting and more. This easy-to-wire  kit is perfect for  anybody with a basic knowledge of electrical wiring,  and can easily be  wired to many 12V applications. For PC Modders, the  end of result of  the Remote Control 12VDC kit is truly impressive and is  sure to impress  the crowds. For DIYers, the kit will give some magical  effect to your  projects.
Encoding and Decoding
The popular link is like this: MCU -> Encoder -> Transmitter ------  Receiver -> Decoder -> MCU, 
PT2262(Encoder) are  optional,their existence is to 1)avoid  confusing when multiple RF links in  range 2) isolate disturbance. 
You   can integrate the encoding and decoding work  to the MCUs on both  side.  Whenever there is no 433.92MHz devices around, you may  use it as  direct  cable connection.
 
Qty : 1 pcs PT2262 transmitter module and 4 pcs 1 channels relay switch ;
 
Transmitter : 
 
Model No.
TB416 Encoder Transmitter
Function discription
Encoder Transmitter modules 
Operating voltage
9V DC
Work current
>100mA
Operating frequency
433MHz
modulation Mode
ASK/OOK
SAW Frequency stability
±150kHz(max)
Transmitter power 
>55mW
Data rate
≤10Kbps
Antenns length

24 cm (315 MHz), 18 cm (433.92 MHz)
Dimension
49*31*8mm
Encodeing format SC2262 fixing code (same as PT2264 PT2262 ),   Work with PT2272 decoder IC
Transmitter distance 1000Meter (open area) 
 
Connect to MCU or Ardiuno :
Connect to Switch:
 
 
 
 
 
Relay receiver : 
 
 
receiver Features:
Typical applications:
   
DC 12V Home lighting system
Remote control switch
Smart Home / Home Automation
Garage Door
Fluorescent lamp Illumination
Motorcycle Electromobile
Remote controlled gates
Security Monitoring
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
   
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lamp, fans, motors and other DC 12V Electrical equipment
 
 
Wiring Diagram 2:
DC 1-48V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lamp, fans, motors and other DC AC equipment
 
 
receiver Features:
   
1 Operating voltage: DC 12V;
2 Operating Current: relays close, about 9MA; relay open,about 42MA;
3 Operating frequency: 433.92M; 315M version can be customized
4 Receiver sensitivity : -108dBm
5 Decode : learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 32 remote control
6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch),Delay; 1-5000 seconds adjustable delay time, minimum step 0.1 seconds
7 Size(Including housing)50*35*22mm
8 Weight(including housing) 30g
9 Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC,10A/12VDC
 
 
Work mode
NO : Relay normally open contact
COM : Relay common contact
NC : Relay normally closed contact
Open : NO connection COM, NC disconnect COM
Close : NO disconnect COM, NC connection COM
Momentary : Press the Transmitter button , the receiver relay is Open, release button;the relay is Close;
Toggle : Press transmitter button for 1 time , the receiver relay is Open, press button again, the relay is Close;
Latched : Press transmitter button A, the receiver relay is Open Press transmitter button B, the receiver relay is Close.
Delay : Press the Transmitter button, the receiver relay Open,After a set time delay, the receiver relay is Close;
If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay Close
  
Adapter remote control (learning remote control):
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
  
Clean code: press the key and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
  
Step 1 (into the learning mode): Press the key (about 1 second), LED off;
Step 2 (adapter button): Then press the utton on the remote control, LED flashes four times on, then learning the button value
  
Note:
Only the Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch) mode to a "clear code" and " learning " action
In the "delay" mode can only set the delay time
  
Delay setting:
Step 1, the mode is set to "delay" mode (jumper cap on the M1 into two rows of pins)
Step 2, press the key until the LED is off
Step 3. Click the key again, LED flashes
Step 4. Click the key again after a period of time, LED light
LED blinking time is the delay time.

Product Name:ALTERA MAX II EPM570 CPLD Core Board & USB Blaster FPGA Programmer Downloader JTAG PLD Logic Development kit for Matrix LED LCD
 
Module No#:  RT319
 
Packing list:
 
1 PCS EPM570 core board
1 PCS Altera USB Blaster #with USB wire and  10 pin JTAG wire#
 
Description: 
 
EPM570 Board Description:
 
Onboard EPM570T100C5N chip, LEs and Equivalent Macrocells More than doubled EPM240
 
50Mhz Active crystal
 
All pins from CPLD are Labelled and available onboard
 
Altera Official standards JTAG Interface
 
Two 5V 3#3V output to provide power for the peripheral
 
A Independent button for test core board
 
Two independent LED lights for test core board
 
Size : 9cm X 6cm #9:6 is Golden ratio ^_^#
 
Diagram :  Please contact me on ebay message for diagram after your order !
 

 
PCB Board 3D View:
 
 
Altera USB Blaster:
 

 
Feature :
1.Stably support SignalTap II embedded logic analyzer function ,no mistake while crawlling data;
2. Fully support all Altera products such as :
   CPLD: MAX3000, MAX7000, MAX9000 and MAXII
   FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc#
   Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc#
   Enhanced configuration devices: EPC1, EPC4#
3# Supports 3 download mode: AS, PS and JTAG;
4. Support and Nios II embedded soft core processor communication and debugging, Rev.C latest version Hardware. Support jtag_uart;
5. Speed: 6 times faster than parallel port download cable ByteBlasterII;
6. Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
7. Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
8: Voltage : 1.5~5V JTAG IO Voltage .
 
 
System configuration:
1, Windows XP, Windows Vista, Windows7 ,USB interface;
2, Quartus II version 4.0 or newer version;
 
This programmer uses standard 10-Pin ICD10 interface, the Pin assignment is shown as followed:
10-Pin interface #the triangle mark on cable "" means 1st pin#:
 
 
 

 
 
Product Name: with ARDUINO sketch 16x16 Matrix Dot Red mini LED Display for UNO MEGA2560 DUE NANO LEONARDO MICRO Raspberry Pi
 
Packing list:
1 PCS mini size 16x16 1.9mm F2.0 Red Pixel Dot Matrix LED
 
Description:
 
Matrix display module 16x16 dot
Red pixels
Pixel size: 1.9MM
74hc595 driver
Can display variety of patterns and characters
Provided arduiuo UNO/MGEA2560 code
Size(Excluding Pin): 40MM x 40MM x 10mm(mini)
Weight : 18.5g
Applicable MCU platform :
UNO MEGA2560 DUE NANO LEONARDO MICRO
FPGA/CPLD
STM32 C51 AVR PIC
raspberry pi
Nodemcu
NOTE :
1 For ARDUIUO CPU frequency is relatively low, If more than 3 modules are connected in series, the LED will flash..
2 We only provide ARDUINO sketch, MCU (C51/ARM/AVR) please modify the code by yourself, ''modify IO port operation mode''
 
 
With the display you get full documentantion and example sketch by email!
 
 
Use:
 
USE for Arduiuo UNO R3:
 
 
You can use this software,make your favorite patterns:
 
 
 
Display effect:
 

Product Name: 15W Electrical isolation DC-DC Boost-Buck Converter 5V 6V 9V 18V 24V to -12V 15V Single voltage to double voltage Module
       
Packing list:
  
1 PCS 5-32 VDC to ±12V( 24V)/±15V( 30V) Isolated DC-DC Buck Converter
Description:
 
2 in 1 Isolated DC-DC Boost-Buck Converter 
 
Input Voltage Range: 5-32 VDC
 
Output Voltage :  ±12V/ 24V(MAX 700MA); ±15V/ 30V(MAX 550MA) 
 
Minimum Load Requirements: 0% (as 24V/ 30V Output), 10% (as -12/ -15 Output) 
 
Efficiency : 70% -88%  
 
Quiescent current : 68mA(Input 12V)
 
Low Noise : 50mV 
 
Hihg Accuracy ： /-1%  
 
Working frequency 400KHz   
 
Isolation (Input to Output): 1500VDC minimum (1 minute) 
 
Isolation Capacitance: 1200pF 
 
Short Circuit Protection 
 
Operating ambient temperature : -40~ 85 Degrees Celsius  
 
Storage Temperature Range: -55 to 125  Degrees Celsius  
 
Size : 68 x 44 x 16mm  
 
Weight :  39g(With terminal), 34g(no terminal) 
 
 
Pin description:
VIN    :  Input positive
GND  :  Input negative
EN     :  Input enable (NC or VIN enable, GND disabled)
V     :  Isolated output positive voltage
COM  :  Isolated output common
V-      :  Isolated output negative voltage
      
 
Applications
  
ADC/DAC/Operational Amplifier 
RS232 RS485 RS422 Bus
Audio equipment
Low power audio power supply
Car audio amplifier dual power board
LCD power supply
Instrumentation equipment
Instrumentation multimeter
    
Attention :
    
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
 
 
 
 
 
 
 
 
 
 

Product Name: 15W Electrical isolation DC-DC Boost-Buck Converter 5V 6V 9V 18V 24V to -12V 15V Single voltage to double voltage Module
       
Packing list:
  
1 PCS 5-32 VDC to ±12V( 24V)/±15V( 30V) Isolated DC-DC Buck Converter
Description:
 
2 in 1 Isolated DC-DC Boost-Buck Converter 
 
Input Voltage Range: 5-32 VDC
 
Output Voltage :  ±12V/ 24V(MAX 700MA); ±15V/ 30V(MAX 550MA) 
 
Minimum Load Requirements: 0% (as 24V/ 30V Output), 10% (as -12/ -15 Output) 
 
Efficiency : 70% -88%  
 
Quiescent current : 68mA(Input 12V)
 
Low Noise : 50mV 
 
Hihg Accuracy ： /-1%  
 
Working frequency 400KHz   
 
Isolation (Input to Output): 1500VDC minimum (1 minute) 
 
Isolation Capacitance: 1200pF 
 
Short Circuit Protection 
 
Operating ambient temperature : -40~ 85 Degrees Celsius  
 
Storage Temperature Range: -55 to 125  Degrees Celsius  
 
Size : 68 x 44 x 16mm  
 
Weight :  39g(With terminal), 34g(no terminal) 
 
 
Pin description:
VIN    :  Input positive
GND  :  Input negative
EN     :  Input enable (NC or VIN enable, GND disabled)
V     :  Isolated output positive voltage
COM  :  Isolated output common
V-      :  Isolated output negative voltage
      
 
Applications
  
ADC/DAC/Operational Amplifier 
RS232 RS485 RS422 Bus
Audio equipment
Low power audio power supply
Car audio amplifier dual power board
LCD power supply
Instrumentation equipment
Instrumentation multimeter
    
Attention :
    
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
 
 
 
 
 
 
 
 
 
 

Product Name: 15W Electrical isolation DC-DC Boost-Buck Converter 5V 6V 9V 18V 24V to -12V 15V Single voltage to double voltage Module
       
Packing list:
  
1 PCS 5-32 VDC to ±12V( 24V)/±15V( 30V) Isolated DC-DC Buck Converter
Description:
 
2 in 1 Isolated DC-DC Boost-Buck Converter 
 
Input Voltage Range: 5-32 VDC
 
Output Voltage :  ±12V/ 24V(MAX 700MA); ±15V/ 30V(MAX 550MA) 
 
Minimum Load Requirements: 0% (as 24V/ 30V Output), 10% (as -12/ -15 Output) 
 
Efficiency : 70% -88%  
 
Quiescent current : 68mA(Input 12V)
 
Low Noise : 50mV 
 
Hihg Accuracy ： /-1%  
 
Working frequency 400KHz   
 
Isolation (Input to Output): 1500VDC minimum (1 minute) 
 
Isolation Capacitance: 1200pF 
 
Short Circuit Protection 
 
Operating ambient temperature : -40~ 85 Degrees Celsius  
 
Storage Temperature Range: -55 to 125  Degrees Celsius  
 
Size : 68 x 44 x 16mm  
 
Weight :  39g(With terminal), 34g(no terminal) 
 
 
Pin description:
VIN    :  Input positive
GND  :  Input negative
EN     :  Input enable (NC or VIN enable, GND disabled)
V     :  Isolated output positive voltage
COM  :  Isolated output common
V-      :  Isolated output negative voltage
      
 
Applications
  
ADC/DAC/Operational Amplifier 
RS232 RS485 RS422 Bus
Audio equipment
Low power audio power supply
Car audio amplifier dual power board
LCD power supply
Instrumentation equipment
Instrumentation multimeter
    
Attention :
    
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
 
 
 
 
 
 
 
 
 
 

Product Name: 15W Electrical isolation DC-DC Boost-Buck Converter 5V 6V 9V 18V 24V to -12V 15V Single voltage to double voltage Module
       
Packing list:
  
1 PCS 5-32 VDC to ±12V( 24V)/±15V( 30V) Isolated DC-DC Buck Converter
Description:
 
2 in 1 Isolated DC-DC Boost-Buck Converter 
 
Input Voltage Range: 5-32 VDC
 
Output Voltage :  ±12V/ 24V(MAX 700MA); ±15V/ 30V(MAX 550MA) 
 
Minimum Load Requirements: 0% (as 24V/ 30V Output), 10% (as -12/ -15 Output) 
 
Efficiency : 70% -88%  
 
Quiescent current : 68mA(Input 12V)
 
Low Noise : 50mV 
 
Hihg Accuracy ： /-1%  
 
Working frequency 400KHz   
 
Isolation (Input to Output): 1500VDC minimum (1 minute) 
 
Isolation Capacitance: 1200pF 
 
Short Circuit Protection 
 
Operating ambient temperature : -40~ 85 Degrees Celsius  
 
Storage Temperature Range: -55 to 125  Degrees Celsius  
 
Size : 68 x 44 x 16mm  
 
Weight :  39g(With terminal), 34g(no terminal) 
 
 
Pin description:
VIN    :  Input positive
GND  :  Input negative
EN     :  Input enable (NC or VIN enable, GND disabled)
V     :  Isolated output positive voltage
COM  :  Isolated output common
V-      :  Isolated output negative voltage
      
 
Applications
  
ADC/DAC/Operational Amplifier 
RS232 RS485 RS422 Bus
Audio equipment
Low power audio power supply
Car audio amplifier dual power board
LCD power supply
Instrumentation equipment
Instrumentation multimeter
    
Attention :
    
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
 
 
 
 
 
 
 
 
 
 

Kit No. : RT397
 
This remote switch allows you to remotely control any 12 Volt DC device. Perfect for controlling any 12V devices such as Lights, Fans, Landscaping Lighting and more. This easy-to-wire kit is perfect for anybody with a basic knowledge of electrical wiring, and can easily be wired to many 12V applications. For PC Modders, the end of result of the Remote Control 12VDC kit is truly impressive and is sure to impress the crowds. For DIYers, the kit will give some magical effect to your projects.
 
Encoding and Decoding
The popular link is like this: MCU -> Encoder -> Transmitter ------ Receiver -> Decoder -> MCU,
PT2262(Encoder) are optional, their existence is to 1)avoid confusing when multiple RF links in range 2) isolate disturbance.
You can integrate the encoding and decoding work to the MCUs on both side. Whenever there is no 433.92MHz devices around, you may use it as direct cable connection.
Qty : 1 pcs PT2262 transmitter module and 4 pcs 1 channels relay switch ;
 
 
Transmitter :
 
Model No.
TB195 Encoder Transmitter
Function discription
Encoder Transmitter modules
Operating voltage
3V ~ 12V DC
Static current
max≤8mA(12V)min≤2mA(3V)
Operating frequency
433MHz
modulation Mode
ASK/OOK
SAW Frequency stability
±150kHz(max)
Transmitter Power
50mW (315MHz, 12V)
Data rate
≤10Kbps
Antenns length

24 cm (315 MHz), 18 cm (433.92 MHz)
Dimension
36 * 27mm
Encodeing format PT2264 fixing code (same as PT2262 SC2262 ) , Work with PT2272 decoder IC
Transmitter distance 100M (open area)
Connect to MCU or Ardiuno :
Connect to Switch:
 
Relay receiver : 
 
 
receiver Features:
Typical applications:
   
DC 12V Home lighting system
Remote control switch
Smart Home / Home Automation
Garage Door
Fluorescent lamp Illumination
Motorcycle Electromobile
Remote controlled gates
Security Monitoring
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
   
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lamp, fans, motors and other DC 12V Electrical equipment
 
 
Wiring Diagram 2:
DC 1-48V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lamp, fans, motors and other DC AC equipment
 
 
receiver Features:
   
1 Operating voltage: DC 12V;
2 Operating Current: relays close, about 9MA; relay open,about 42MA;
3 Operating frequency: 433.92M; 315M version can be customized
4 Receiver sensitivity : -108dBm
5 Decode : learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 32 remote control
6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch),Delay; 1-5000 seconds adjustable delay time, minimum step 0.1 seconds
7 Size(Including housing)50*35*22mm
8 Weight(including housing) 30g
9 Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC,10A/12VDC
 
 
Work mode
NO : Relay normally open contact
COM : Relay common contact
NC : Relay normally closed contact
Open : NO connection COM, NC disconnect COM
Close : NO disconnect COM, NC connection COM
Momentary : Press the Transmitter button , the receiver relay is Open, release button;the relay is Close;
Toggle : Press transmitter button for 1 time , the receiver relay is Open, press button again, the relay is Close;
Latched : Press transmitter button A, the receiver relay is Open Press transmitter button B, the receiver relay is Close.
Delay : Press the Transmitter button, the receiver relay Open,After a set time delay, the receiver relay is Close;
If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay Close
  
Adapter remote control (learning remote control):
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
  
Clean code: press the key and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
  
Step 1 (into the learning mode): Press the key (about 1 second), LED off;
Step 2 (adapter button): Then press the utton on the remote control, LED flashes four times on, then learning the button value
  
Note:
Only the Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch) mode to a "clear code" and " learning " action
In the "delay" mode can only set the delay time
  
Delay setting:
Step 1, the mode is set to "delay" mode (jumper cap on the M1 into two rows of pins)
Step 2, press the key until the LED is off
Step 3. Click the key again, LED flashes
Step 4. Click the key again after a period of time, LED light
LED blinking time is the delay time.

 
Product Name: 12V 24V 12 NPN Digital IO RS485 Relay Module Modbus RTU DIN35 C45 Rail Box for PLC PTZ Configuration Software touch screen
 
 
 
Package inlcuded:
  1PCS DC 12V/24V 12 Input & 12 Output RS485 Relay Module
 
 
Description:
1: DC 12V (12V Version), DC 24V (24V Version)
 
2: Standby current (all relays closed) 14MA, 1 relay open 41MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 226MA
 
3 12 photoelectric isolation Input ports (NPN low level active ), the input and output relationship can be set to associated (default) and non-associated through commands.
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' ''''Interlock between two channels'' 7 Commands
 
5: MODBUS RTU command, Support 03 06 16 function code
 
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 The default baud rate is 9600BPS. The baud rate can be selected through jumpers: 2400 4800 9600 19200BPS
 
10 Size: 180 * 72 * 20mm(Only PCB Board);184 * 88* 42mm(with Din Rail Box)
11 Weight: 190g(Only PCB Board);318g(with Din Rail Box)
12 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
  
 
For more information, please contact me
 
DIN rail Box parameters:
Product model: UM72
Color: green
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 180 mm PCB boards
Net weight: 128g
Installation: DIN35 and C45 rail
 
 
Application
 
PLC IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
Configuration Software
 
Typical applications:
1 The dial switch (slave address) is invalid and can only control one module at a time.
 
MODBUS RTU command mode (HEX), you can control a variety of ways: Serial Hyper Terminal Control (need to manually add the CRC), Modbus Poll software control (software automatically add the CRC), PLC or MCU process control
 
 
 
Wiring Diagram:
 
1 DC 12V/24 control circuit,Wiring diagram below. ''LOAD'' may be camera,LED lights, fans, motors and other DC 12V/24V equipment
 
 
 
 
2 DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V/24V load, need another DC 12V/24V power supply). ''LOAD'' may be LED lights, fans, motors Lights, fluorescent lights, solar water heaters and other DC AC equipmen
Test Software(We offer a demo video):
Serial HyperTerminal:
 
Modbus Poll
 
 
 
 

 
Product Name: 12V 24V 12 NPN Digital IO RS485 Relay Module Modbus RTU DIN35 C45 Rail Box for PLC PTZ Configuration Software touch screen
 
 
 
Package inlcuded:
  1PCS DC 12V/24V 12 Input & 12 Output RS485 Relay Module
 
 
Description:
1: DC 12V (12V Version), DC 24V (24V Version)
 
2: Standby current (all relays closed) 14MA, 1 relay open 41MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 226MA
 
3 12 photoelectric isolation Input ports (NPN low level active ), the input and output relationship can be set to associated (default) and non-associated through commands.
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' ''''Interlock between two channels'' 7 Commands
 
5: MODBUS RTU command, Support 03 06 16 function code
 
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 The default baud rate is 9600BPS. The baud rate can be selected through jumpers: 2400 4800 9600 19200BPS
 
10 Size: 180 * 72 * 20mm(Only PCB Board);184 * 88* 42mm(with Din Rail Box)
11 Weight: 190g(Only PCB Board);318g(with Din Rail Box)
12 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
  
 
For more information, please contact me
 
DIN rail Box parameters:
Product model: UM72
Color: green
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 180 mm PCB boards
Net weight: 128g
Installation: DIN35 and C45 rail
 
 
Application
 
PLC IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
Configuration Software
 
Typical applications:
1 The dial switch (slave address) is invalid and can only control one module at a time.
 
MODBUS RTU command mode (HEX), you can control a variety of ways: Serial Hyper Terminal Control (need to manually add the CRC), Modbus Poll software control (software automatically add the CRC), PLC or MCU process control
 
 
 
Wiring Diagram:
 
1 DC 12V/24 control circuit,Wiring diagram below. ''LOAD'' may be camera,LED lights, fans, motors and other DC 12V/24V equipment
 
 
 
 
2 DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V/24V load, need another DC 12V/24V power supply). ''LOAD'' may be LED lights, fans, motors Lights, fluorescent lights, solar water heaters and other DC AC equipmen
Test Software(We offer a demo video):
Serial HyperTerminal:
 
Modbus Poll
 
 
 
 

 
Product Name: 12V 24V 12 NPN Digital IO RS485 Relay Module Modbus RTU DIN35 C45 Rail Box for PLC PTZ Configuration Software touch screen
 
 
 
Package inlcuded:
  1PCS DC 12V/24V 12 Input & 12 Output RS485 Relay Module
 
 
Description:
1: DC 12V (12V Version), DC 24V (24V Version)
 
2: Standby current (all relays closed) 14MA, 1 relay open 41MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 226MA
 
3 12 photoelectric isolation Input ports (NPN low level active ), the input and output relationship can be set to associated (default) and non-associated through commands.
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' ''''Interlock between two channels'' 7 Commands
 
5: MODBUS RTU command, Support 03 06 16 function code
 
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 The default baud rate is 9600BPS. The baud rate can be selected through jumpers: 2400 4800 9600 19200BPS
 
10 Size: 180 * 72 * 20mm(Only PCB Board);184 * 88* 42mm(with Din Rail Box)
11 Weight: 190g(Only PCB Board);318g(with Din Rail Box)
12 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
  
 
For more information, please contact me
 
DIN rail Box parameters:
Product model: UM72
Color: green
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 180 mm PCB boards
Net weight: 128g
Installation: DIN35 and C45 rail
 
 
Application
 
PLC IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
Configuration Software
 
Typical applications:
1 The dial switch (slave address) is invalid and can only control one module at a time.
 
MODBUS RTU command mode (HEX), you can control a variety of ways: Serial Hyper Terminal Control (need to manually add the CRC), Modbus Poll software control (software automatically add the CRC), PLC or MCU process control
 
 
 
Wiring Diagram:
 
1 DC 12V/24 control circuit,Wiring diagram below. ''LOAD'' may be camera,LED lights, fans, motors and other DC 12V/24V equipment
 
 
 
 
2 DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V/24V load, need another DC 12V/24V power supply). ''LOAD'' may be LED lights, fans, motors Lights, fluorescent lights, solar water heaters and other DC AC equipmen
Test Software(We offer a demo video):
Serial HyperTerminal:
 
Modbus Poll
 
 
 
 

 
Product Name: 12V 24V 12 NPN Digital IO RS485 Relay Module Modbus RTU DIN35 C45 Rail Box for PLC PTZ Configuration Software touch screen
 
 
 
Package inlcuded:
  1PCS DC 12V/24V 12 Input & 12 Output RS485 Relay Module
 
 
Description:
1: DC 12V (12V Version), DC 24V (24V Version)
 
2: Standby current (all relays closed) 14MA, 1 relay open 41MA, 2 relays open 69MA, 3 relays open 95MA,4 relays open 122MA,5 relays open 149MA,6 relays open 174MA, 7 relays open 198MA,8 relays open 226MA
 
3 12 photoelectric isolation Input ports (NPN low level active ), the input and output relationship can be set to associated (default) and non-associated through commands.
 
4: ''open'' ''close'' ''Momentary'' ''Self-locking'' ''Interlock'' ''Delay'' ''''Interlock between two channels'' 7 Commands
 
5: MODBUS RTU command, Support 03 06 16 function code
 
6: Under the ''Delay'' command ,the maximum delay is 255 seconds;
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll'' Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
9 The default baud rate is 9600BPS. The baud rate can be selected through jumpers: 2400 4800 9600 19200BPS
 
10 Size: 180 * 72 * 20mm(Only PCB Board);184 * 88* 42mm(with Din Rail Box)
11 Weight: 190g(Only PCB Board);318g(with Din Rail Box)
12 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
  
 
For more information, please contact me
 
DIN rail Box parameters:
Product model: UM72
Color: green
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 180 mm PCB boards
Net weight: 128g
Installation: DIN35 and C45 rail
 
 
Application
 
PLC IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ CCTV Camera
Security Monitoring
Identification system;
Motor FW & BW
Automatic curtain control
Configuration Software
 
Typical applications:
1 The dial switch (slave address) is invalid and can only control one module at a time.
 
MODBUS RTU command mode (HEX), you can control a variety of ways: Serial Hyper Terminal Control (need to manually add the CRC), Modbus Poll software control (software automatically add the CRC), PLC or MCU process control
 
 
 
Wiring Diagram:
 
1 DC 12V/24 control circuit,Wiring diagram below. ''LOAD'' may be camera,LED lights, fans, motors and other DC 12V/24V equipment
 
 
 
 
2 DC 1-110V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V/24V load, need another DC 12V/24V power supply). ''LOAD'' may be LED lights, fans, motors Lights, fluorescent lights, solar water heaters and other DC AC equipmen
Test Software(We offer a demo video):
Serial HyperTerminal:
 
Modbus Poll
 
 
 
 

Below item is powered by Canton-electronics Ltd .
 
​Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.
 
Modules No: RT390
 
1 pcs Super-Heterodyne decoder receiver and 1 pcs 12 buttons PT2262 encoder transmitter ;
 
 
 
Receiver :
 
Module No.: RF11A04
 
Description:
Model No.: RF11A04 OR CE-RF11A-045V
1. Features:
Operating voltage: DC 3-5V
Operating current: less 11mA (DC 5V)
Working priceple: super heterodyne
modulation Mode: OOK / ASK
Operating Frequency : 433.92MHZ
Receiving sensitivity: -108dBm
Output level: 5V TTL level, low standby, the maximum current 20MA (to add a current-limiting resistor)
Decode: learning code, adapted EV1527 / PT2262 and a compatible remote control, you can store up to eight remote control
Working modes: Non-locking (Momentary ), self-locking (Toggle), Inter-locking; 0.1-500000 seconds adjustable delay time
Size: 30x12.1x12.5mm
Weight: 4 grams or less
 
 
2. Pin Description
G: GND pin, DC 3-5V power supply negative
V: VCC pin, DC 3-5V positive power supply
D0: channel 1 output, active high
D1: channel 2 output, active high
D2: Channel 3 output, active high
D3: Channel 4 output, active high
VT: channel output valid signal, the microcontroller can be used as an interrupt signal
 
3. the working mode
 
You can select different modes of operation with"M4 M3 M2 M1 M0" pad in the delay mode to adjust the delay time through an adjustable resistor.
In delay mode, the rotary variable resistor can adjust the delay time. Increase the time counterclockwise rotation, and clockwise rotation to shorten the time. Adjustable resistor is a precision resistor, adjust the time with a Phillips screwdriver to gently rotate (do not use excessive force)
Working Mode Description:
Non-locking: Press the remote control button, the IO port outputs high. Release the remote control button, IO port outputs low.
Self-locking: Press the remote control button, the IO port outputs high. Press the remote control button again, IO port outputs low.
Interlock: Press the remote control button D0, D0 IO port outputs high, other IO ports outputs low; remote control button is pressed D1, D1 IO port outputs high, other IO ports output low and so on.
Delay: Under Delay mode, there is a delay 0/1/2/3/4 five sub-patterns, by adjusting the variable resistor IO port high duration
4, the adapter remote control (learning remote control)
In normal operation mode, LED (D1) will be lit, when receiving a valid remote control (EV1527 / PT2262) key value, LED will flash.
Clean code: hold the button to press.LED offs, keep pressing about 8 seconds until LED lights. At that time, clean code completion (Note: After the implementation of clean code, previous remote controls do not exist.
Adaptation (learning):
Step 1 (into the learning mode):trigger the key button, LED offs;
Step 2 (adapter channel 1): press the first button of remote control and then, LED offs after flashes for four times. This time means that it had learned the value of the first button
Step 3 (Adaptation Channel 2): Press the second remote control, LED offs after flashes 4 times, This time means that it had learned the value of the second button
Step 4 (adapter Channel 3): Then press the remote's third button, LED offs after flashes 4 times, This time means that it had learned the value of the third button
Step 5 (Adaptation Channel 4): Then press the remote control's fourth button, LED lights after flashes 4 times, This time means that it had learned the value of the fourth button.
NOTE: The process must be completed within 15 seconds
 
Adaptation Video,Click here!
 
5. Wiring Diagram :
Control LED indicator: see "RF11A04_LED demo"
Control 12V Relay: See "RF11A04_4Relay demo"
Click here for more help!
 
 
 
Connect with ardiuno :
 
 
 
 
Transmitter :
 
 
Features / Specifications :
1. 4 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
 
Technical Data :
Transmitter Module No.: TB420;
Power supply : 12V 23A battery (not included )  ,
 
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format: SCT2260  fixed code (compatiable for PT2262 SC2262 PT2260 PT2264 , can work with PT2272-M4 ,PT2272-T4,PT2272-L4 );
RC  Resistance : 4.7M; 
Transmit power : 200mW ;
 

Typical applications:
   
DC 12V Home lighting system
Remote control switch
Smart Home / Home Automation
Garage Door
Fluorescent lamp Illumination
Motorcycle Electromobile
Remote controlled gates
Security Monitoring
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
   
Wiring Diagram 1:
DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lamp, fans, motors and other DC 12V Electrical equipment
 
 
Wiring Diagram 2:
DC 1-48V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lamp, fans, motors and other DC AC equipment
 
 
 
 
 
Packing list:
1 PCS 433M DC 12V one Channel Delay Relay
1 PCS 433M Large Power 1 Button PT2262 Remote Control(USE 12V 23A battery,Batteries not included)
receiver Features:
   
1 Operating voltage: DC 12V;
2 Operating Current: relays close, about 9MA; relay open,about 42MA;
3 Operating frequency: 433.92M; 315M version can be customized
4 Receiver sensitivity : -108dBm
5 Decode : learning code, can be adapted EV1527 / PT2262 and compatible remote control, you can store up to 32 remote control
6 Work mode : Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch),Delay; 1-5000 seconds adjustable delay time, minimum step 0.1 seconds
7 Size(Including housing)50*35*22mm
8 Weight(including housing) 30g
9 Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC,10A/12VDC
  
 
Work mode
NO : Relay normally open contact
COM : Relay common contact
NC : Relay normally closed contact
Open : NO connection COM, NC disconnect COM
Close : NO disconnect COM, NC connection COM
Momentary : Press the Transmitter button , the receiver relay is Open, release button;the relay is Close;
Toggle : Press transmitter button for 1 time , the receiver relay is Open, press button again, the relay is Close;
Latched : Press transmitter button A, the receiver relay is Open Press transmitter button B, the receiver relay is Close.
Delay : Press the Transmitter button, the receiver relay Open,After a set time delay, the receiver relay is Close;
If during the delay, press the button of Transmitter, delay start again; if the delay period, press and hold the button of Transmitter 3-4 seconds, the receiver controller stops the delay, the relay Close
  
Adapter remote control (learning remote control):
Under normal operating mode, LED will be lit, when receives a valid remote control (EV1527 / PT2262) button values, LED flashes
  
Clean code: press the key and held down, LED off, LED will light about 8 seconds later, clean code is completed (Note: After performing clean code previously stored remote control value does not exist)
  
Step 1 (into the learning mode): Press the key (about 1 second), LED off;
Step 2 (adapter button): Then press the utton on the remote control, LED flashes four times on, then learning the button value
  
Note:
Only the Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch) mode to a "clear code" and " learning " action
In the "delay" mode can only set the delay time
  
Delay setting:
Step 1, the mode is set to "delay" mode (jumper cap on the M1 into two rows of pins)
Step 2, press the key until the LED is off
Step 3. Click the key again, LED flashes
Step 4. Click the key again after a period of time, LED light
LED blinking time is the delay time.
 
 
 
Transmitter :
 
 
 
Features / Specifications :
1. 1 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
 
Technical Data :
Transmitter Module No.: TB419;
Power supply : 12V 23A battery (not included ) , please buy battery from here : .
 
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format:  EV1527  fixed code ; 
Transmit power : 200mW ;
 

 
Product Name: DC 12V 2CH RKE Secure Remote Keyless Entry System Remote Controller Rolling Code Keyfob Kit for Motor Forward and reverse
 
 
 
Package inlcuded:
1 PCS 433M DC 12V 2CH Rolling code Relay Board Module
1 PCS 433M HCS301 Remote Control(Does not include 12V 27A battery)
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 13MA, 1 relay open 41MA, 2 relays open 69MA
3. Wireless Receiving frequency : 433Mhz ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. size (including shell) 62*58*30mm;
8. weight : 51 grams;
9. Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door
Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
PTZ Camera
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Product number : RC43A04
Rolling Code (HCS301)
Use 12V 27A battery, battery not included
Weight : 28gram.

 
Product Name: DC 12V 2CH RKE Secure Remote Keyless Entry System Remote Controller Rolling Code Keyfob Kit for Motor Forward and reverse
 
 
 
Package inlcuded:
1 PCS 433M DC 12V 2CH Rolling code Relay Board Module
1 PCS 433M HCS301 Remote Control(Does not include 12V 27A battery)
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 13MA, 1 relay open 41MA, 2 relays open 69MA
3. Wireless Receiving frequency : 433Mhz ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. size (including shell) 62*58*30mm;
8. weight : 51 grams;
9. Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door
Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
PTZ Camera
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Product number : RC43A04
Rolling Code (HCS301)
Use 12V 27A battery, battery not included
Weight : 28gram.

 
Product Name: DC 12V 2CH RKE Secure Remote Keyless Entry System Remote Controller Rolling Code Keyfob Kit for Motor Forward and reverse
 
 
 
Package inlcuded:
1 PCS 433M DC 12V 2CH Rolling code Relay Board Module
1 PCS 433M HCS301 Remote Control(Does not include 12V 27A battery)
 
 
Description:
 
1. Operating Voltage: DC 12V;
2. Operating Current: Standby current (all relays closed) 13MA, 1 relay open 41MA, 2 relays open 69MA
3. Wireless Receiving frequency : 433Mhz ;
4. Wireless Receiving sensitivity: -108dBm ;
5. Decoding type: Rolling Code, Only adapted to RC43A04(Our company's HCS301 Remote control) Remote Control , Can store up to 32PCS RC43A04 remote controls;
6. Working modes: Non-locking (Momentary is defult),Self-locking (Toggle),Inter-locking (Latch), Delay; delay time can be 5 seconds, 10 seconds, 120 seconds;
7. size (including shell) 62*58*30mm;
8. weight : 51 grams;
9. Relay Maximum load(Recommended<5A):10A/250VAC,10A/125VAC,10A/30VDC, 10A/28VDC ,10A/12VDC .
 
It is recommended to buy multiple remote controllers as a spare
 
For more information, please contact me
 
Application
 
Remote control, remote measurement system;
DC 12V Home lighting system
Garage Door
Elevators
Motor reversing control
Remote control switch
Smart Home / Home Automation
LED lighting
Fluorescent lamp
DC 12 DC Motor,RS360
PTZ Camera
 
 
Remote Control Description:
Remote model : RC43A04(Rolling code);
Power supply : 12V 27A battery replacable .(This remote doesnot have a battery , Please buy in your local market )
Operating current: ≤ 9mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK;
Operating frequency:433.92MHZ;
Frequency deviation:± 150Hz (max);
Encoding format: Rolling Code ( HCS301) ;
Transmit power:10 mW.
Weight : 28gram.
 
Product number : RC43A04
Rolling Code (HCS301)
Use 12V 27A battery, battery not included
Weight : 28gram.

 
 
Product Name: DC 12V 24V 8DI 8DO Multifunction RS485 Modbus RTU Relay Module Support 01 05 15 02 03 06 16 Function Code Switch Control Board
 
 
 
Package inlcuded:
 
1PCS DC 12V/24V 8DI 8DO Modbus RTU RS485 Relay Module
 
 
Description:
 
1:DC 12V (12V Version),DC 24V (24V Version)
 
2.Standby current (all relays closed) 14MA, 1 relay open 40MA, 2 relays open 68MA, 3 relays open 96MA,4 relays open 122MA,5 relays open 149MA,6 relays open 177MA, 7 relays open 202MA,8 relays open 226MA
3:8 photoelectric isolation Input ports (NPN low level active ).
The input-output relationship can be set to various association modes through instructions(Self-lockingdefault)/Interlocking/Momentary/Interlocking/Output=Input)
4: Support standard Modbus RTU command, function code, write 05/06/15/16 read 01/02/03
 
5: With hardware reset function, with TVS anti-surge protection
 
6 8 opto-isolated inputs (NPN), 8 relay outputs (upgraded relays, more durable)
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll''Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
8 The default baud rate is 9600BPS. The baud rate can be selected by Conmand 2400 4800 9600 19200 38400 57600 115200BPS
 
10 The parity can be none parity, even parity and odd parity
 
11 The data sending and returning time can be set,with a maximum value of 1000ms
 
12 Size: 136 * 72 * 12mm(Only PCB Board);138 * 82*40mm(with Din Rail Box)
13 Weight: 143g(Only PCB Board);239g(with Din Rail Box)
14 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
Upgraded Features:
MODBUS RTU Function Code 01 05 15 02 03 06 16
Support more input-output relationships
Support more baud rates, can modify the parity bit
Hardware reset to factory settings (RESET jumper)
Upgraded relays (more durable)
TVS anti-surge protection
For more information, please contact me
Application
 
PLC RS485 IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ Camera
Security Monitoring
Identification system;
LED Lamp Drivers
Automatic curtain control
Battery Test Detection System
DIN rail Box parameters:
Product model: UM72
Color: Grey
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 136 mm PCB boards
Net weight: 99g
Installation: DIN35 and C45 rail
 
 
 
 

 
 
Product Name: DC 12V 24V 8DI 8DO Multifunction RS485 Modbus RTU Relay Module Support 01 05 15 02 03 06 16 Function Code Switch Control Board
 
 
 
Package inlcuded:
 
1PCS DC 12V/24V 8DI 8DO Modbus RTU RS485 Relay Module
 
 
Description:
 
1:DC 12V (12V Version),DC 24V (24V Version)
 
2.Standby current (all relays closed) 14MA, 1 relay open 40MA, 2 relays open 68MA, 3 relays open 96MA,4 relays open 122MA,5 relays open 149MA,6 relays open 177MA, 7 relays open 202MA,8 relays open 226MA
3:8 photoelectric isolation Input ports (NPN low level active ).
The input-output relationship can be set to various association modes through instructions(Self-lockingdefault)/Interlocking/Momentary/Interlocking/Output=Input)
4: Support standard Modbus RTU command, function code, write 05/06/15/16 read 01/02/03
 
5: With hardware reset function, with TVS anti-surge protection
 
6 8 opto-isolated inputs (NPN), 8 relay outputs (upgraded relays, more durable)
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll''Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
8 The default baud rate is 9600BPS. The baud rate can be selected by Conmand 2400 4800 9600 19200 38400 57600 115200BPS
 
10 The parity can be none parity, even parity and odd parity
 
11 The data sending and returning time can be set,with a maximum value of 1000ms
 
12 Size: 136 * 72 * 12mm(Only PCB Board);138 * 82*40mm(with Din Rail Box)
13 Weight: 143g(Only PCB Board);239g(with Din Rail Box)
14 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
Upgraded Features:
MODBUS RTU Function Code 01 05 15 02 03 06 16
Support more input-output relationships
Support more baud rates, can modify the parity bit
Hardware reset to factory settings (RESET jumper)
Upgraded relays (more durable)
TVS anti-surge protection
For more information, please contact me
Application
 
PLC RS485 IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ Camera
Security Monitoring
Identification system;
LED Lamp Drivers
Automatic curtain control
Battery Test Detection System
DIN rail Box parameters:
Product model: UM72
Color: Grey
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 136 mm PCB boards
Net weight: 99g
Installation: DIN35 and C45 rail
 
 
 
 

 
 
Product Name: DC 12V 24V 8DI 8DO Multifunction RS485 Modbus RTU Relay Module Support 01 05 15 02 03 06 16 Function Code Switch Control Board
 
 
 
Package inlcuded:
 
1PCS DC 12V/24V 8DI 8DO Modbus RTU RS485 Relay Module
 
 
Description:
 
1:DC 12V (12V Version),DC 24V (24V Version)
 
2.Standby current (all relays closed) 14MA, 1 relay open 40MA, 2 relays open 68MA, 3 relays open 96MA,4 relays open 122MA,5 relays open 149MA,6 relays open 177MA, 7 relays open 202MA,8 relays open 226MA
3:8 photoelectric isolation Input ports (NPN low level active ).
The input-output relationship can be set to various association modes through instructions(Self-lockingdefault)/Interlocking/Momentary/Interlocking/Output=Input)
4: Support standard Modbus RTU command, function code, write 05/06/15/16 read 01/02/03
 
5: With hardware reset function, with TVS anti-surge protection
 
6 8 opto-isolated inputs (NPN), 8 relay outputs (upgraded relays, more durable)
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll''Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
8 The default baud rate is 9600BPS. The baud rate can be selected by Conmand 2400 4800 9600 19200 38400 57600 115200BPS
 
10 The parity can be none parity, even parity and odd parity
 
11 The data sending and returning time can be set,with a maximum value of 1000ms
 
12 Size: 136 * 72 * 12mm(Only PCB Board);138 * 82*40mm(with Din Rail Box)
13 Weight: 143g(Only PCB Board);239g(with Din Rail Box)
14 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
Upgraded Features:
MODBUS RTU Function Code 01 05 15 02 03 06 16
Support more input-output relationships
Support more baud rates, can modify the parity bit
Hardware reset to factory settings (RESET jumper)
Upgraded relays (more durable)
TVS anti-surge protection
For more information, please contact me
Application
 
PLC RS485 IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ Camera
Security Monitoring
Identification system;
LED Lamp Drivers
Automatic curtain control
Battery Test Detection System
DIN rail Box parameters:
Product model: UM72
Color: Grey
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 136 mm PCB boards
Net weight: 99g
Installation: DIN35 and C45 rail
 
 
 
 

 
 
Product Name: DC 12V 24V 8DI 8DO Multifunction RS485 Modbus RTU Relay Module Support 01 05 15 02 03 06 16 Function Code Switch Control Board
 
 
 
Package inlcuded:
 
1PCS DC 12V/24V 8DI 8DO Modbus RTU RS485 Relay Module
 
 
Description:
 
1:DC 12V (12V Version),DC 24V (24V Version)
 
2.Standby current (all relays closed) 14MA, 1 relay open 40MA, 2 relays open 68MA, 3 relays open 96MA,4 relays open 122MA,5 relays open 149MA,6 relays open 177MA, 7 relays open 202MA,8 relays open 226MA
3:8 photoelectric isolation Input ports (NPN low level active ).
The input-output relationship can be set to various association modes through instructions(Self-lockingdefault)/Interlocking/Momentary/Interlocking/Output=Input)
4: Support standard Modbus RTU command, function code, write 05/06/15/16 read 01/02/03
 
5: With hardware reset function, with TVS anti-surge protection
 
6 8 opto-isolated inputs (NPN), 8 relay outputs (upgraded relays, more durable)
 
7 MODBUS commands can be made serial HyperTerminal (serial assistant) OR ''Modbus Poll''Enter;
 
8 Under the MODBUS command mode, it can support up to 64 devices in parallel
 
8 The default baud rate is 9600BPS. The baud rate can be selected by Conmand 2400 4800 9600 19200 38400 57600 115200BPS
 
10 The parity can be none parity, even parity and odd parity
 
11 The data sending and returning time can be set,with a maximum value of 1000ms
 
12 Size: 136 * 72 * 12mm(Only PCB Board);138 * 82*40mm(with Din Rail Box)
13 Weight: 143g(Only PCB Board);239g(with Din Rail Box)
14 Maximum load: 10A / 250VAC, 10A / 125VAC, 10A / 30VDC, 10A / 28VDC, 10A / 12VDC
 
Upgraded Features:
MODBUS RTU Function Code 01 05 15 02 03 06 16
Support more input-output relationships
Support more baud rates, can modify the parity bit
Hardware reset to factory settings (RESET jumper)
Upgraded relays (more durable)
TVS anti-surge protection
For more information, please contact me
Application
 
PLC RS485 IO expansion board
Smart Home,Home Automation ,Wiser Home;
PTZ Camera
Security Monitoring
Identification system;
LED Lamp Drivers
Automatic curtain control
Battery Test Detection System
DIN rail Box parameters:
Product model: UM72
Color: Grey
Width: suitable for PCB board width UM72(72mm)
Insulation grade: flame-retardant VO grade
Backplane length: suitable for 136 mm PCB boards
Net weight: 99g
Installation: DIN35 and C45 rail
 
 
 
 

Brand Name : eletechsup
Certification : None
Origin : CN(Origin)
is_customized : Yes
Voltage : 12V
Model Number : IO55C02
Protect Feature : Epoxy
Power Source : DC
Usage : General Purpose
Product Name:200W 12V 24V DC Motor Driver Module 433M Wireless Remote Controller Forward Reverse Limit Speed Board
Product Included:
1 * Motor Speed Controller (include speed knob)and 1*remote control(Does not include 12V 23A battery)
OR 1*Remote control(Does not include 12V 23A battery)
OR 1 * Motor Speed Controller(include speed knob)
Note: Please use the remote control we sell, otherwise it may not be compatible with the remote control.
Features:
1. Provides variable speed capability for DC motor, also provides limit function.
2. Achieves start, stop, speed up and down, positive and reverse rotation RC controlled.
3. DC Motor Speed Controller can achieve simple automatic functions.
4. It can remote control the speed up and down, positive and reversing rotation and stop of the brushed DC motor.
5. It owns powerful function, stable performance and beautiful appearance.
Motor Speed Controller Description:
•Applicable voltage: DC 12V~30V (DC power supply power ≥ motor power x1.3)
•Wireless receiving sensitivity: -108dBm
•Decoding type: fixed code, can be adapted to up to 32 remote controls
•Working modes: click to move, self-locking
•Size(including shell): 115*90*40mm
•Weight (including speed control knob): 194.1g
•Applicable motor: brushed DC motor, rated power of 24V DC motor <100W, limit value 200W, rated power of 12V DC motor <50W, limit value 100W
•Speed regulation function: After the governor is powered on, both the knob and the remote control can control the speed. If the adjustment knob exceeds 5% of the range, the knob speed regulation mode is preferred, and the remote control speed regulation mode is preferred to use the remote control speed regulation
Remote Control Description:
•Remote model : TB453(fixed code)
•Power supply : 12V 23A battery replacable (This remote doesnot have a battery , Please buy in your local market )
•Operating current: ≤ 9mA
•Oscillation mode: SAW resonator
•Modulation mode:ASK
•Operating frequency:433.92MHZ
•Frequency deviation:± 150Hz (max)
•Encoding format: Fixed Code ( EV1527)
•Transmit power: 10 mW
•Weight : 36.9g
Operating mode:
Speed knob:

Brand Name : eletechsup
Certification : None
Origin : CN(Origin)
is_customized : Yes
Voltage : 12V
Model Number : IO55C02
Protect Feature : Epoxy
Power Source : DC
Usage : General Purpose
Product Name:200W 12V 24V DC Motor Driver Module 433M Wireless Remote Controller Forward Reverse Limit Speed Board
Product Included:
1 * Motor Speed Controller (include speed knob)and 1*remote control(Does not include 12V 23A battery)
OR 1*Remote control(Does not include 12V 23A battery)
OR 1 * Motor Speed Controller(include speed knob)
Note: Please use the remote control we sell, otherwise it may not be compatible with the remote control.
Features:
1. Provides variable speed capability for DC motor, also provides limit function.
2. Achieves start, stop, speed up and down, positive and reverse rotation RC controlled.
3. DC Motor Speed Controller can achieve simple automatic functions.
4. It can remote control the speed up and down, positive and reversing rotation and stop of the brushed DC motor.
5. It owns powerful function, stable performance and beautiful appearance.
Motor Speed Controller Description:
•Applicable voltage: DC 12V~30V (DC power supply power ≥ motor power x1.3)
•Wireless receiving sensitivity: -108dBm
•Decoding type: fixed code, can be adapted to up to 32 remote controls
•Working modes: click to move, self-locking
•Size(including shell): 115*90*40mm
•Weight (including speed control knob): 194.1g
•Applicable motor: brushed DC motor, rated power of 24V DC motor <100W, limit value 200W, rated power of 12V DC motor <50W, limit value 100W
•Speed regulation function: After the governor is powered on, both the knob and the remote control can control the speed. If the adjustment knob exceeds 5% of the range, the knob speed regulation mode is preferred, and the remote control speed regulation mode is preferred to use the remote control speed regulation
Remote Control Description:
•Remote model : TB453(fixed code)
•Power supply : 12V 23A battery replacable (This remote doesnot have a battery , Please buy in your local market )
•Operating current: ≤ 9mA
•Oscillation mode: SAW resonator
•Modulation mode:ASK
•Operating frequency:433.92MHZ
•Frequency deviation:± 150Hz (max)
•Encoding format: Fixed Code ( EV1527)
•Transmit power: 10 mW
•Weight : 36.9g
Operating mode:
Speed knob:

Brand Name : eletechsup
Certification : None
Origin : CN(Origin)
is_customized : Yes
Voltage : 12V
Model Number : IO55C02
Protect Feature : Epoxy
Power Source : DC
Usage : General Purpose
Product Name:200W 12V 24V DC Motor Driver Module 433M Wireless Remote Controller Forward Reverse Limit Speed Board
Product Included:
1 * Motor Speed Controller (include speed knob)and 1*remote control(Does not include 12V 23A battery)
OR 1*Remote control(Does not include 12V 23A battery)
OR 1 * Motor Speed Controller(include speed knob)
Note: Please use the remote control we sell, otherwise it may not be compatible with the remote control.
Features:
1. Provides variable speed capability for DC motor, also provides limit function.
2. Achieves start, stop, speed up and down, positive and reverse rotation RC controlled.
3. DC Motor Speed Controller can achieve simple automatic functions.
4. It can remote control the speed up and down, positive and reversing rotation and stop of the brushed DC motor.
5. It owns powerful function, stable performance and beautiful appearance.
Motor Speed Controller Description:
•Applicable voltage: DC 12V~30V (DC power supply power ≥ motor power x1.3)
•Wireless receiving sensitivity: -108dBm
•Decoding type: fixed code, can be adapted to up to 32 remote controls
•Working modes: click to move, self-locking
•Size(including shell): 115*90*40mm
•Weight (including speed control knob): 194.1g
•Applicable motor: brushed DC motor, rated power of 24V DC motor <100W, limit value 200W, rated power of 12V DC motor <50W, limit value 100W
•Speed regulation function: After the governor is powered on, both the knob and the remote control can control the speed. If the adjustment knob exceeds 5% of the range, the knob speed regulation mode is preferred, and the remote control speed regulation mode is preferred to use the remote control speed regulation
Remote Control Description:
•Remote model : TB453(fixed code)
•Power supply : 12V 23A battery replacable (This remote doesnot have a battery , Please buy in your local market )
•Operating current: ≤ 9mA
•Oscillation mode: SAW resonator
•Modulation mode:ASK
•Operating frequency:433.92MHZ
•Frequency deviation:± 150Hz (max)
•Encoding format: Fixed Code ( EV1527)
•Transmit power: 10 mW
•Weight : 36.9g
Operating mode:
Speed knob:

 
 

 
Product Name:5pcs 3V 3.3V 3.7V 6V to 5V Boost Buck DC-DC Step Up Down Converter usb power supply for Ardiuno UNO MEGA DUE YUN AVR FPGA CPLD
 
Packing list 
  
5 pcs USB Auto buck-boost Voltage regulator (input DC 1-6V , output DC 5V -6% ) ;
 
Description: 
  
Input voltage DC 1 ~ 6V, output DC 5V( -6% )
The maximum input voltage can not exceed 6.5V
Short-term maximum output current : 12000mA
Long time maximum output current: 1000mA
Auto Buck-Boost Converter Module working frequency 1MHZ.efficiency 60% -85% .
Operating temperature range : -25~ 85 Degrees Celsius
Storage temperature range : -45~ 125 Degrees Celsius
 Size : 47mm x 16mm x 13.7mm
Weight : 4.6g 
  
    
      
Applications:
  
Battery powered equipment
Wireless Module,NRF24L01 CC1101 CC2500 etc.
MCU Development Board,AVR PIC FPGA/CPLD STM32 
Arduiuo uno mega2560 due YUN Breadboard Raspberry Pi
LED Lighting
Wireless communication equipment
Audio equipment
Digital cameras,GPS,wireless transceiver
Portable devices
 
  
Attention :
  
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low

   
   
   
   
   
   
   
   
   
   
   
   
Kit No. : RT396
 
This remote switch allows you to remotely control any 12 Volt DC device. Perfect for controlling any 12V devices such as Lights, Fans, Landscaping Lighting and more. This easy-to-wire kit is perfect for anybody with a basic knowledge of electrical wiring, and can easily be wired to many 12V applications. For PC Modders, the end of result of the Remote Control 12VDC kit is truly impressive and is sure to impress the crowds. For DIYers, the kit will give some magical effect to your projects.
 
Encoding and Decoding
The popular link is like this: MCU -> Encoder -> Transmitter ------ Receiver -> Decoder -> MCU,
PT2262(Encoder) are optional, their existence is to 1)avoid confusing when multiple RF links in range 2) isolate disturbance.
You can integrate the encoding and decoding work to the MCUs on both side. Whenever there is no 433.92MHz devices around, you may use it as direct cable connection.
Qty : 1 pcs PT2262 transmitter module and 1 pcs 4 channels relay switch ;
 
 
Transmitter :
 
Model No.
TB195 Encoder Transmitter
Function discription
Encoder Transmitter modules
Operating voltage
3V ~ 12V DC
Static current
max≤8mA(12V) min≤2mA(3V)
Operating frequency
433MHz
modulation Mode
ASK/OOK
SAW Frequency stability
±150kHz(max)
Transmitter Power
50mW (315MHz, 12V)
Data rate
≤10Kbps
Antenns length

24 cm (315 MHz), 18 cm (433.92 MHz)
Dimension
36 * 27mm
Encodeing format PT2264 fixing code (same as PT2262 SC2262 ) Work with PT2272 decoder IC
Transmitter distance 100M (open area)
 
Connect to MCU or Ardiuno :
 
Connect to Switch: