Kereskedelmi, irodai és ipari

 
 
Product Name:   R411A01_3V3 mini 3.3V Auto RS485 to TTL232 Converter Board SP3485 LvTTL RS232 MAX3485 for FPGA CPLD ESP8266 HC-05 Wifi Bluetooth Module
 
 
 
Package inlcuded:
1 PCS R411A01_3V3 DC 3.3V RS485 to LvTTL 232 converter
 
 
Description:
 
Read and write automatic control RS485 TO RS232(3.3V TTL Logic level) converter
 
Operating Voltage : DC 3.3V
Logic level : 3.3V LvTTL Logic level
RS485 BUS IC : SP3485
Read and write automatic control IC :SM74HC04
7x 2.54MM pin,mini size.
Size(Does not include pin) : 17.9x11.7x2.8mm(very small)
Weight :1.2g(Very light)
 
Application
 
RS485 Temperature and humidity sensor
PTZ camera
LED controller
MODBUS RTU
RS485 Relay
485 sensor
automated manufacturing line
Wifi to RS485(ESP8266)
Bluetooth to RS485(HC-05/HC06)
 
Wiring Diagram:
 
 

Modules No: TB132
 
Qty: 1 pcs step-up modules (input 3.5~9V , output 9V ) ;
 
Description: 
 
1: Input less then 5V ,  power is 1-2W;
    Input is 5-6V, power is 2.7-4W;
    Input is 6- 9V, power is 5W-8W;
 
2: DC-DC Boost module working frequency 100KHZ. efficiency is normal 80%   !
3: Attention to cooling problems, continuous output must take care of the heat!
The module operating temperature -10 ~ 80 degrees; Please note that more than 80 degrees heat, Easily burn module (you can mount heat sink);
Note: no icing or condensation of water vapor, in order to avoid short-circuit;we suggest resin potting ;
 
Attention : 
1: Boost modules or buck module indicate the operating voltage, Please donot exceed operating voltage , or it will be damaged easily !
2: Boost module output voltage can only be greater than or equal to input voltage, cannot be less than the input voltage!
3: Buck module input voltage must be higher than output voltage of 1.5V or 2V, otherwise it can not output enough power!
4: Automatic Adjustable Boost or Buck module has start voltage and limit working voltage, Please donot exceed them , or it will be damaged easily !
5: Cannot reverse polarity , or it will be short circuit, or will be  born easily !
 
Typical application :  

Below item is powered by Canton-Power Ltd.
 
Product Name:  DD06AJSA DC 2.6-6V to 3-15V Adjustable Output Board DC DC Boost Step up Converter Voltage Regulator Module
  
Packing list:
 
1 PCS 2.6V-6V TO 3-15V adjustable Step-up Boost Module
Description:
 
Input voltage 2.6~6V,output 3~15V adjustable
Maximum input current :  1.4A
Long-term work Current : 1.2A
Conversion efficiency : 80-90%
   
DC-DC Boost module working frequency 1.0MHZ. 
Operating ambient temperature : -40~ 85 Degrees Celsius
2.54mm pin pitch,Arduiuo UNO MEGA2560 DUE Breadboard XILINX ALTERA LATTICE FPGA/CPLD AVR  Development Board friendly.
 
Excluding Pin Size 20mm x 10.16mm x 5.6mm(Very small)
Weight : about 1.3g(Very light)
 
Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.
 
 
Start Voltage 2.6V, Output Current 10MA
Input  Voltage

Input  Current

Output  Voltage

Output  Curren
2.8V

0.94A

3V

0.7A
2.8V

1.05A

3.3V

0.7A
3V

0.93A

3.26V

0.7A
2.8V

1A

3.72V

0.63A
3V

1.16A

3.7V

0.77A
3.3V

1A

3.7V

0.74A
2.8V

1A

4.5V

0.52A
3V

1.15A

4.52V

0.62A
3.3V

1.2A

4.5V

0.72A
3.7V

1.2A

4.49V

0.83A
2.8V

1A

5.07V

0.46A
3V

1.13A

5.06V

0.55A
3.3V

1.2A

5.04V

0.66A
3.7V

1.23A

5.02V

0.76A
4.5V

1A

5V

0.79A
 
     
2.8V

1A

6.09V

0.38A
3V

1.12A

6.10V

0.46A
3.3V

1.22A

6.08V

0.54A
3.7V

1.22A

6.06V

0.63A
4.5V

1.2A

6.03V

0.78A
5V

1.3A

6.00V

0.95A
2.8V

0.64A

9.11V

0.17A
3V

0.78A

9.12V

0.22A
3.3V

0.98A

9.14V

0.3A
3.7V

1.20A

9.15V

0.41A
4.5V

1.32A

9.16V

0.56A
5V

1.3A

9.15V

0.63A
6V

1.2A

9.11V

0.71A
3V

0.15A

12.15V

0.03A
3.3V

0.51A

12.18V

0.12A
3.7V

0.87A

12.23V

0.23A
4.5V

1.33A

12.16V

0.42A
5V

1.4A

12.16V

0.5A
6V

1.2A

12.17V

0.53A
 
 
Applications
 
MCU Development Board,FPGA/CPLD UNO MEGA2560 DUE 8051 AVR C8051 etc
PLC  RS485 Modbus RTU
Network equipment/Router
Temperature and humidity sensor
LED Lighting
Instruments and meters
5V 6V 9V 12V Relay board
Wireless communication equipment
315M 433M Wireless remote controller
 
Attention :
  
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
 
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
how to use:
With a suitable screwdriver, slowly rotating adjustable resistance
 
 
 

Product Name:2pcs 2.54mm Female Pin Header 4 Button key Switch Keyboard kit for raspberry pi FPGA CPLD ARM AVR Development Board
 
 
Packing list:
 
2 PCS  2.54mm Female Pin Header 4 Button key;
 
 
Description:
 
Can be inserted directly into raspberry pi FPGA CPLD ARM AVR Development Board
,Ideal for linking up to your   raspberry pi AVR STM32 RM PIC AT89C51 STC MSP430 STM8 XILINX ALTERA  FPGA CPLD etc.
  
1 4-button Common Cathode key module .
 
2 " GND K1 K2 K3 K4" 4 2.54mm Female Pin Header
 
3 Size: 12.7MM x 33MM.
 

Circuit schematics : 
 

Below item is powered by Canton-Power Ltd . 
 
Product Name:   1.5V 1.8V 3V 3.3V to 3.7V DC/DC Converter Step up Boost Module for X5C Quadcopter Aircraft Drone Wltoys Lipo Battery
  
Packing list:
 
1 PCS DD0606SB_3V7 1V-3.7V TO 3.7V Step-up Boost Module
 
  
Description:
Input voltage DC 1 ~ 3.7V, output DC 3.7V( -5% )
 
DC DC Boost Converter Module working frequency 1MHZ.efficiency 66% -88% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Size : 21.3mm x 12.5mm x 5.7mm(Very small)
 
Weight : 1.66g(Very light) 
 
 
   
Applications
Battery powered equipment
Breadboard Power Supply
ARM STM32 FPGA CPLD Board
Wireless Module,  esp8266 nrf24l01 rtl8710 GSM etc
3.3V Small power motors
Camera, Video camera
3.3V Toy car
PDA
LED Lighting
Wireless communication equipment
Audio equipment 
 
 
Attention :
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 

Product Name : mini 1.4Mhz 1.2A DC DC Converter Step Down DC 6.5V 9V 12V 15V 18V 20V to 5V Buck Module
  
  Packing list:
1 PCS mini 1.2A DC DC Converter Step Down 6.5V-23V to 5V
 
 
Description: 
 
Input voltage 6.5~23V,output 5V
 
Maximum output current 1.2A,Short time maximum output current 2A
 
DC-DC Step-Down Converter module working frequency 1.4MHz. efficiency is 80-92% .
 
2.54mm pin pitch, Arduiuo Breadboard MCU Development Board friendly
 
Excluding Pin Size 22.5mm x 13.5mm x 6.5mm( small)
 
Weight : about 2.2g( Very light)
 
 
Applications:
 
MCU Development Board,FPGA/CPLD UNO MEGA2560 DUE 8051 AVR C8051 etc
5V LED Lighting
5V Motor
Mobile phone charger
Wireless communication equipment
Smart home / home automation
315M 433M Wireless remote controller
Distributed Power Systems 
Battery Charger 
Pre-Regulator for Linear Regulators 
DSL Modems
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 

 
Product Name :     1A DC 5-40V to 3.3V Regulator DC-DC Step-Down Buck Converter Module Board replace AMS1117-3.3 LM1117-3.3 1117 LDO 
    
 Packing list:
 
1 PCS DD4012SA_3V3 5V-40V to 3.3V DC DC Buck Converter Module 
    
 
Description: 
 
Input voltage 5~40V,output 3.3V
 
Maximum output current 1A
 
DC-DC Step-Down Converter module working frequency 550KHz. efficiency is 76-90% .
 
Quiescent current: about 1.5MA
 
Overtemperature shutdown, input under-voltage protection, BS-voltage protection, and short circuit protection.
 
2.54mm pin pitch, Arduiuo UNO MEGA2560 Breadboard MCU Development Board friendly
 
Excluding Pin Size 18.3mm x 10.2mm x 6.7mm( small)
 
Weight : about 1.3g(Very light)
 
  
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
Applications:
 
3.3V MCU ARM CPU FPGA/CPLD 
12V 5V TO 3.3V lithium battery-powered systems
3.3V Motor
WIFI esp8266 Module
CCTV camera
Wireless Module:Nrf24l01 CC1101 CC2500 CC2530 Zigbee
Smart home / home automation
Distributed Power Systems
Battery Charger
Pre-Regulator for Linear Regulators
​replace AMS1117-3.3 LM1117-3.3 1117 LDO 
 
 

Below item is powered by Canton-electronics Ltd . 
 
Product Name:  DD0606SA_3V 1-3V to 3V DC-DC Step-up Boost Converter Module Voltage Regulator Board for A AA  Dry battery cell
  
Packing list:
 
1 PCS 1V-3V TO 3V Step-up Boost Module
  
Description:
Input voltage DC 1 ~ 3V, output DC 3V( -5% )
DC DC Boost Converter Module working frequency 1MHZ.efficiency 65% -88% .
Operating temperature range : -25~ 85 Degrees Celsius
Storage temperature range : -45~ 125 Degrees Celsius
2.54mm pin pitch,MCU Development Board Breadboard friendly.
Excluding Pin Size : 21.3mm x 12.5mm x 5.7mm(Very small)
Weight : 1.85g(Very light) 
 Applications
Battery powered equipment
Breadboard Power Supply
Wireless Module, NRF24L01 Zigbee CC1101 CC2500 etc
3V Small power motors
Camera, Video camera
3V Toy car
PDA
LED Lighting
Wireless communication equipment
Audio equipment 
 
 
Attention :
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 

Below item is powered by Canton-Power Ltd . 
 
Product Name:   DD0606SB_4V5 1.5V 3V 3.7V to 4.5V DC DC Converter Step up Boost Board for 18650 aa battery stepper motor
  
Packing list:
 
1 PCS DD0606SB_4V5 1V-4.5V TO 4.5V Step-up Boost Module
 
  
Description:
Input voltage DC 1 ~ 4.5V, output DC 4.5V( -5% )
 
DC DC Boost Converter Module working frequency 1MHZ.efficiency 66% -88% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Excluding Pin Size : 21.3mm x 12.5mm x 5.7mm(Very small)
 
Weight : 1.66g(Very light) 
 
 
   
Applications
Battery powered equipment
Breadboard Power Supply
ARM STM32 FPGA CPLD Board
Wireless Module,  esp8266 nrf24l01 rtl8710 GSM etc
4.5V Small power motors
Camera, Video camera
4.5V Toy car
18650 & aa battery
PDA
LED Lighting
Wireless communication equipment
Audio equipment 
 
 
Attention :
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
 
   
 
 
 

Nama produk:  1A DC 9 V 12 V 15 V 24 V 6 V DC DC converter power supply modul Langkah -Down Modul Regulator Tegangan
Daftar kemasan:
 
1 pcsDD4012SB_6V 7.5 V-40 V 6 V DC DC Buck Converter Modul
Deskripsi:
Tegangan Input 7.5 ~ 40 V, output 6 V
 
Arus keluaran maksimum 1A
 
DC-DC Step-Down modul Konverter frekuensi kerja 550 KHz. efisiensi 75-90% .
 
Diam saat ini: Tentang 1.5MA
 
Overtemperature shutdown, masukan di bawah tegangan perlindungan, BS-Perlindungan tegangan dan perlindungan sirkuit pendek.
 
2.54mm pin lapangan Arduiuo UNO MEGA2560 Papan Tempat Memotong Roti MCU Dewan Pengembangan ramah
 
Ukuran 18.3mm X 10.2mm x 6.7mm(Kecil)
Berat: sekitar 1.1g(Sangat terang)
Perhatian:
Ini adalah DC-DC tegangan converter modul harus dicatat dengan menggunakan:
1 tegangan Input tidak dapat lebih besar dari maksimum berbagai masukan
2 daya keluaran tidak dapat lebih besar dari beban maksimum untuk waktu yang lama
3 daya Input harus lebih besar dari daya output, karena konsumsi daya modul itu sendiri
Aplikasi:
12 V 9 V UNTUK 6 V baterai lithium bertenaga sistem
6 V Motor Mainan
WIFI ESP8266 HC-12 Modul Bluetooth
CCTVKamera
Mainan elektrik
Modul nirkabel: Nrf24l01 CC1101 CC2500 CC2530 Zigbee
Smart Home/home Automation
Distributed Power Sistem
Baterai Charger
-Regulator untuk Linear Regulator
FM radio
Baterai peralatan
Audio amplifier

Below item is powered by Canton-Power Ltd . 
 
Product Name:   DD0606SB_5V 1.5V 3V 3.7V to 5V  DC DC Boost Step up Converter Power Supply Module for Motor USB LED LCD power bank 
  
Packing list:
 
1 PCS DD0606SB_5V 1V-5V TO 5V DC DC Boost Converter Module
 
  
Description:
Input voltage DC 1 ~ 5V, output DC 5V( -5% )
 
DC DC Boost Converter Module working frequency 1MHZ.efficiency 66% -88% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Excluding Pin Size : 21.3mm x 12.5mm x 5.7mm(Very small)
 
Weight : 1.85g(Very light) 
 
 
   
Applications
Battery powered equipment
Breadboard Power Supply
ARM STM32 FPGA CPLD Board
Small power motors
Camera, Video camera
Toy car
power bank 
Phone PDA
LED Lighting
Wireless communication equipment
Audio equipment 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
 
   
 
 
 

Nama produk: 3.7 V 5 V untuk 9 V DC DC Converter Step-Up Meningkatkan Current Mode PWM Tegangan Transformasi Modul
Daftar kemasan:
1 PCS 5 W 3 V-6 V 9 V Meningkatkan Langkah UP Voltage Regulator    Modul

 
 
Deskripsi:
Tegangan Input 2.8 ~ 6 V, output 9 V (penyimpangan -5% )
Input maksimum saat ini: 1.2A
Jangka Panjang bekerja Saat Ini: 1A
Efisiensi konversi: 81-91%
Mulai Tegangan 2.8 V, Output Saat Ini 60MA
INPUT 3 V 1A; OUTPUT 9 V 290MA
INPUT 3.3 V 1A; OUTPUT 9 V 330MA
INPUT 3.7 V 1A; OUTPUT 9 V 360MA
INPUT 4.5 V 1A; OUTPUT 9 V 440MA
MASUKAN 5 V 1A; OUTPUT 9 V 490MA
INPUT 6 V 1A; OUTPUT 9 V 590MA
DC-DC Meningkatkan modul bekerja frekuensi 1.0 MHZ.
Ambient operasi suhu:-40 ~ 85 Derajat Celcius
2.54mm pin lapangan Arduiuo UNO KARENA Papan Tempat Memotong Roti FPGA/CPLD  Development BoardRamah.
Tidak termasuk Pin Ukuran 20.5mm x 10.16mm x 5.6mm (Sangat kecil)
Berat: sekitar 1.4g (Sangat ringan)
Aplikasi:
MCU Dewan Pengembangan, FPGA/CPLD UNO MEGA2560 KARENA 8051 AVR C8051 dll
PLC Modbus RS485
Peralatan Jaringan/Router
VIDEO PLAYER
PDA
Lampu LED
9 V Relay papan
Komunikasi nirkabel peralatan
315 M 433 M remote kontrol Nirkabel
Perhatian:
Ini adalah DC-DC tegangan converter modul harus dicatat dengan menggunakan:
1 tegangan Input tidak dapat lebih besar dari maksimum berbagai masukan
2 daya keluaran tidak dapat lebih besar dari beban maksimum untuk waktu yang lama
3 daya Input harus lebih besar dari daya output, karena konsumsi daya modul itu sendiri
Q & A:
Q: Mengapa tegangan output kurang dari Tegangan nominal
A: Input power supply power terlalu rendah. uji tegangan input dengan digital t ini tegangan input yang sangat rendah

Product Name:  50-1000MA Adjustable 3.7V 4.2V Li-ion Rechargeable lithium Battery Charger Module replace TP4056 
 
 
 
Packing list:
 
1 PCS  DD07CRTA 3.7V Li Lithium Battery 50-1000MA Charger Module 
 
  
 
Description: 
     
100-2700mAh(50-1000MA) Lithium Battery Charger Module - Linear charging.
     
Input voltage : DC 4.5V-8V(Recommend DC 5V)
 
Charger current : 50-1000MA(Adjust Rprog value)
 
Full charge voltage : 4.2V -2% .
 
Led indicator :
"OK" LED is fully charged OR battery failure status indicator;
"CR" LED is charge status indicator
Operating ambient temperature : -40° to 85°
Storage temperature : -65° to 125°
Size : 30x15x6mm
Weight :1.75g
      
Can be used DC 4.5V-8V power supply charger(Such as Solar panels)Charging module comes with charge-management functions, will not overcharge or over discharge
Comes with rechargeable function,Will enter standby mode when fully charged.When the battery capacity is below 80% , the charging start.
    
Charger current(MA) = Battery capacity(mAh) * 0.37
For example :
1000mAh lithium battery recommended charger current is 370MA
2000mAh lithium battery recommended charger current is 740MA
  
  
  
Applications:
​  
Lithium Battery 14500,14650,17490,18500,18650,26500
Mobile phone
Solar charging
MP3/MP4 player
Audio equipment
Portable Devices
Wife Bluetooth Applications

  
 
 
 
 

Below item is powered by Canton-Power Ltd.
 
Product Name:  DD06AJSB DC 3.3V 3.7V 5V to 6V 9V 12V Adjustable Step-Up Boost Voltage Regulator Power supply Module
  
Packing list:
 
1 PCS DD06AJSB 2.6V-6V TO 3-15V adjustable Step-up Boost Module
 
Description:
 
Input voltage 2.6~6V,output 3~15V adjustable
Maximum input current :  1.4A
Long-term work Current : 1.2A
Conversion efficiency :79-90%
   
DC-DC Boost module working frequency 1.0MHZ. 
Operating ambient temperature : -40~ 85 Degrees Celsius
FPGA/CPLD AVR  Development Board friendly.
 
Size 20mm x 10.16mm x 5.6mm(Very small)
Weight : about 1.2g(Very light)
 
Note: Adjustable resistors (potentiometers) are components that are easily damaged. Use a suitable screwdriver to slowly rotate. Click here to buy a screwdriver.
 
 
Start Voltage 2.6V, Output Current 10MA
Input  Voltage

Input  Current

Output  Voltage

Output  Curren
2.8V

0.94A

3V

0.7A
2.8V

1.05A

3.3V

0.7A
3V

0.93A

3.26V

0.7A
2.8V

1A

3.72V

0.63A
3V

1.16A

3.7V

0.77A
3.3V

1A

3.7V

0.74A
2.8V

1A

4.5V

0.52A
3V

1.15A

4.52V

0.62A
3.3V

1.2A

4.5V

0.72A
3.7V

1.2A

4.49V

0.83A
2.8V

1A

5.07V

0.46A
3V

1.13A

5.06V

0.55A
3.3V

1.2A

5.04V

0.66A
3.7V

1.23A

5.02V

0.76A
4.5V

1A

5V

0.79A
 
     
2.8V

1A

6.09V

0.38A
3V

1.12A

6.10V

0.46A
3.3V

1.22A

6.08V

0.54A
3.7V

1.22A

6.06V

0.63A
4.5V

1.2A

6.03V

0.78A
5V

1.3A

6.00V

0.95A
2.8V

0.64A

9.11V

0.17A
3V

0.78A

9.12V

0.22A
3.3V

0.98A

9.14V

0.3A
3.7V

1.20A

9.15V

0.41A
4.5V

1.32A

9.16V

0.56A
5V

1.3A

9.15V

0.63A
6V

1.2A

9.11V

0.71A
3V

0.15A

12.15V

0.03A
3.3V

0.51A

12.18V

0.12A
3.7V

0.87A

12.23V

0.23A
4.5V

1.33A

12.16V

0.42A
5V

1.4A

12.16V

0.5A
6V

1.2A

12.17V

0.53A
 
 
Applications
 
MCU Development Board,FPGA/CPLD UNO MEGA2560 DUE 8051 AVR C8051 etc
PLC  RS485 Modbus RTU
9-12V Network equipment/Router
Temperature and humidity sensor
LED Lighting
Instruments and meters
5V 6V 9V 12V Relay board
Wireless communication equipment
315M 433M Wireless remote controller
 
Attention :
  
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
Q & A:
 
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
how to use:
With a suitable screwdriver, slowly rotating adjustable resistance
 
 
 

Below item is powered by Canton-Power Ltd . 
 
Input 3.7V/1220MA,Output 6V/640MA 
 
Input 4.5V/1100MA,Output 6V/700MA  
 
Input 5V/940MA,Output 6V/700MA 
 
 
 
   
 
Product Name:    DD0606SA_6V 800MA DC-DC 1.5V 3V 3.3V 3.7V 4.5V 5V to 6V Step-up Boost Converter Module for LED Motor
  
Packing list:
 
1 PCS 1V-6V TO 6V DC DC Boost Converter Module
 
  
Description:
Input voltage DC 1 ~ 6V, output DC 6V( -5% )
 
DC DC Boost Converter Module working frequency 1MHZ.efficiency 66% -88% .
 
Operating temperature range : -25~ 85 Degrees Celsius
 
Storage temperature range : -45~ 125 Degrees Celsius
 
2.54mm pin pitch,MCU Development Board Breadboard friendly.
 
Excluding Pin Size : 21.3mm x 12.5mm x 5.7mm(Very small)
 
Weight : 1.85g(Very light) 
 
 
Applications
Battery powered equipment
Breadboard Power Supply
ARM STM32 FPGA CPLD Board
Wireless Module,  esp8266 nrf24l01 rtl8710 GSM etc
Small power motors
Camera, Video camera
Toy car
Phone PDA
LED Lighting
Wireless communication equipment
Audio equipment 
 
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
 
   
 
 
 

 
Product Name :      DD4012SA_3V 1A DC DC Step Down Converter Module DC 5-40V to 3V Buck Power supply Board replace AMS1117-3.0  
    
  Packing list:
 
1 PCS DD4012SA_3V 4.75V-40V to 3V DC DC Step Down Converter Module 
    
 
Description: 
 
Input voltage 4.75~40V,output 3V
 
Maximum output current 1A
 
DC-DC Step-Down Converter module working frequency 550KHz. efficiency is 75-90% .
 
Quiescent current: about 1.5MA
 
Overtemperature shutdown, input under-voltage protection, BS-voltage protection, and short circuit protection.
 
2.54mm pin pitch, Arduiuo UNO MEGA2560 Breadboard MCU Development Board friendly
 
Excluding Pin Size 18.3mm x 10.2mm x 6.7mm( small)
 
Weight : about 1.3g(Very light)
 
  
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
Applications:
 
3V MCU ARM CPU FPGA/CPLD 
12V 5V TO 3V lithium battery-powered systems
3V Motor
WIFI esp8266 Module
CCTV camera
Wireless Module:Nrf24l01 CC1101 CC2500 CC2530 Zigbee
Smart home / home automation
Distributed Power Systems
Battery Charger
Pre-Regulator for Linear Regulators
 
 

Below item is powered by Canton-electronics Ltd .
Module No.:  TB114
 
Qty : 2 pcs  0-8Ghz SMA 90 degrees connector ; 
 
 
 
 
 

 
Applications:
 
Low-power LED Driver
White LED Backlighting
Li-Ion Battery Backup Supplies
Local 3V to 5V Conversion
Smart Card Readers
PCMCIA Local 5V Supplies
 
 
 
Product Name: DD0505MC 3V 3.3V 3.7V to 5V Charge Pump DC DC Converter Boost Step Up Power Module for LED MCU 18650
 
Packing list:
 
2 PCS DD0505MC 250MA 2.7V-5V to 5V DC DC Boost Converter
 

 
This is a micro-power( only 250MA ) DC-DC Step-Up Converter module.
If you need 1200MA 3V-5V to 5V Boost module ,Click here
If you need 1200MA 5V-23V to 5V Buck module ,Click here
 
Description:
 
Low Noise, Regulated Charge Pump DC/DC Converter
 
It produce a regulated output voltage from a 2.7V to 4.5V input with up to 250mA of output current
 
Fixed 5V -4% Output
 
Voltage Input Range: 2.7~5V
 
Long time maximum output current 200mA
 
Short time maximum output current 250mA
 
working frequency 1.2MHz.
 
Short-Circuit Protection
 
No load input current : 1.8mA
 
2.54mm pin pitch, Arduiuo Breadboard MCU Development Board friendly
 
Excluding Pin Size 11mm x 7.62mm x 2.4mm(Very very small)
 
Weight : about 0.47g(Very very light)
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 

Product Name :  Ultra Small mini DC 3.7V 4.2V 4.5V 5V 6V to 3.3V Step Down Buck Regulator Module  for 18650 ESP8266 breadboard
  
  Packing list:
 
1 PCS mini 500mA DC DC Converter Step Down 3.3V-6V to 3.3V
     
 
  
 
 
 
Description: 
 
Input voltage 3.3-6V, output 3.3V (deviation -5% )
 
Long time maximum output current 500mA
Short time maximum output current 700mA
Conversion efficiency : 80-93%
  
The maximum input voltage can not exceed 6.5V
 
INPUT 3.7V/600MA;  OUTPUT  3.3V/550MA
INPUT 4V/600MA;    OUTPUT  3.3V/610MA
INPUT 4.2V/580MA;  OUTPUT  3.3V/600MA
INPUT 4.5V/550MA;  OUTPUT  3.3V/620MA
INPUT 5V/470MA;    OUTPUT  3.3V/590MA
INPUT 6V/370MA;    OUTPUT  3.3V/550MA
 
DC-DC Buck Step-down module working frequency 1.2MHZ. 
Operating ambient temperature : -40~ 85 Degrees Celsius
2.54mm pin pitch,Arduiuo UNO DUE Breadboard FPGA/CPLD  Development Board friendly.
Excluding Pin Size 10.8mm x 7.7mm x 5.6mm(Very small)
Weight : <1g(Very light)
 
Applications:
 
Wifi Module:ESP8266
Bluetooth module : HC-05 HC-06
Wireless UART module : HC-11 HC-12
wireless module : CC1101 CC2500 Nrf24l01
3-3.5V led lights
3.3V Development Board: ARM FPGA/CPLD MSP430
  
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
   
 

 
Product Name :       1A DC 9V 12V 15V 24V to 7.5V dc dc converter module Step-Down Buck Voltage Regulator power supply Board    
    
  Packing list:
 
1 PCS DD4012SB_7V5 9V-40V to 7.5V DC DC Buck Converter Module 
    
  
 
Description: 
   
Input voltage 9~40V,output 7.5V
 
Maximum output current 1A
 
DC-DC Step-Down Converter module working frequency 550KHz. efficiency is 75-90% .
 
Quiescent current: about 1.5MA
 
Overtemperature shutdown, input under-voltage protection, BS-voltage protection, and short circuit protection.
 
2.54mm pin pitch, Arduiuo UNO MEGA2560 Breadboard MCU Development Board friendly
 
 Size 18.3mm x 10.2mm x 6.7mm( small)
  
Weight : about 1.1g(Very light)
 
  
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
Applications:
  
12V 9V TO 7.5V lithium battery-powered systems
7.5V Motor ​Toy
WIFI Router Switch
CCTV camera
Electric toys
Wireless Module:Nrf24l01 CC1101 CC2500 CC2530 Zigbee
Smart home / home automation
Distributed Power Systems
Battery Charger
Pre-Regulator for Linear Regulators
FM radio
Battery powered equipment
Audio amplifier
 
  
 

 
Product Name :   DD4012SB_3V 1A DC-DC Step-Down Buck Converter Module DC 5V 6V 9V 12V to 3V Voltage regulator Board 
    
  Packing list:
 
1 PCS DD4012SB_3V 4.75V-40V to 3V DC DC Step Down Converter Module 
    
  
 
Description: 
   
Input voltage 4.75~40V,output 3V
 
Maximum output current 1A
 
DC-DC Step-Down Converter module working frequency 550KHz. efficiency is 75-90% .
 
Quiescent current: about 1.5MA
 
Overtemperature shutdown, input under-voltage protection, BS-voltage protection, and short circuit protection.
 
2.54mm pin pitch, Arduiuo UNO MEGA2560 Breadboard MCU Development Board friendly
 
Excluding Pin Size 18.3mm x 10.2mm x 6.7mm( small)
  
Weight : about 1.3g(Very light)
 
  
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
 
 
Applications:
  
3V MCU ARM CPU FPGA/CPLD 
12V 5V TO 3V lithium battery-powered systems
3V Motor​Toy
WIFI esp8266 Module
CCTV camera
Wireless Module:Nrf24l01 CC1101 CC2500 CC2530 Zigbee
Smart home / home automation
Distributed Power Systems
Battery Charger
Pre-Regulator for Linear Regulators
FM radio
Battery powered equipment
Audio amplifier
 
 
 
 

Below item is powered by eletechsup Ltd . 
 
Product Name:   600MA 1.5V 3V 3.3V 3.7V to 5V Boost Step-up DC-DC Converter Module Voltage PFM regulator Board 
  
Packing list:
 
1 PCS 600mA  1-5V to 5V High Efficiency ,synchronous PFM step-up DC-DC converter
  
  
Description:  
Input voltage DC 1 ~ 5V,output DC 5V±2%
  
DC DC Boost Converter Module working frequency 350KHZ.
   
High efficiency : 95% (usually is 76% -93% )
   
Low Quiescent Current : 13uA
     
Ultra-small size : 10.7x10.6x5.6mm
  
Ultra-light weight : 0.65g
  
  
  
Applications
Battery powered equipment
Breadboard Power Supply
Small power motors
Camera, Video camera
Electric toys
Model aircraft
LED Lighting
C8051 STC PIC AVR Board
raspberry pi UNO MEGA2560
electronic diy kit
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself
  
Q & A:
     
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a t this time of the input voltage is very low
 
 
 
   
 
 
 
 

Nama produk: ultra kecil DC-DC 0.8-3.3 V untuk DC 3.3 V Langkah yang LEBIH TINGGI Meningkatkan PFM Tegangan Converter Power Supply modul DC/DC 1.5 V 2 V 2.5 V 3 V untuk KARENA FPGA
 
 
 
Daftar kemasan:
 
1 PCS 0.9 V-3.3 V UNTUK 3.3 V Langkah-UP PFM Tegangan Converter Modul  
 
 
 
Deskripsi:
Tegangan Masukan 0.8 ~ 3.3 V, output 3.3 V
Output maksimum saat ini: 500 MA
Mulai Tegangan 0.8 V, Output Saat Ini 10MA
INPUT 1-1.5 V, OUTPUT 3.3 V 50-110MA;
INPUT 1.5-2 V, OUTPUT 3.3 V 110-160MA;
MASUKAN 2-3 V, OUTPUT 3.3 V 160-400MA;
MASUKAN di atas 3 V, OUTPUT 3.3 V 400-500MA;
DC-DC Meningkatkan modul bekerja frekuensi 150 KHZ.Efisiensi <85% (Direkomendasikan efisiensi tinggi versi)
Tidak termasuk Ukuran Pin 11mm x 10.5mm x 7.5mm (Sangat kecil), Pin 2.54mm pitch
Aplikasi:
Baterai peralatan
Wirels Modul NRF24L01 CC1101 CC2500.
Pengembangan Papan, FPGA/CPLD STM32
Kamera, Video kamera
VIDEO PLAYER
PDA
Lampu LED
Komunikasi nirkabel peralatan
MP3/MP4 pemain
Peralatan Audio
Perhatian:
Ini adalah DC-DC tegangan converter modul harus dicatat dengan menggunakan:
1 tegangan Input tidak dapat lebih besar dari maksimum berbagai masukan
2 daya keluaran tidak dapat lebih besar dari beban maksimum untuk waktu yang lama
3 daya Input harus lebih besar dari daya output, karena konsumsi daya modul itu sendiri

Product Name:  "Small and light" DC/DC 0.8-5V to DC 5V Step UP Boost Voltage Converter Power Supply Module DC-DC in 1.5V 2.5V 3V 3.3V 3.7V 4.5V
 
 
 
Packing list:
 
1 PCS 0.9V-5V TO 5V Step-UP  PFM Voltage Converter Module  
 
 
 
Description: 
Input voltage 0.9 ~ 5V, output 5V
Maximum output current: 500 MA,
 
Start Voltage 0.9V, Output Current 10MA
  
INPUT 1-1.5V,      OUTPUT 5V 50-110MA;
INPUT 1.5-2V,      OUTPUT 5V 110-160MA;
INPUT 2-3V,         OUTPUT 5V 160-400MA;
INPUT above 3V,  OUTPUT 5V 400-500MA;
 
DC-DC Boost module working frequency 180KHZ. efficiency <85% (Recommended high efficiency version).
Operating ambient temperature : -25~ 85 Degrees Celsius
Excluding Pin Size 11mm x 10.5mm x 7.5mm(Very small), 2.54mm pin pitch
 
 Applications:
Battery powered equipment
Wirels Module,NRF24L01 CC1101 CC2500 etc.
Development Board,FPGA/CPLD UNO MEGA2560 DUE 8051 AVR STC etc
Camera, Video camera
VCR
PDA
LED Lighting
Wireless communication equipment
MP3/MP4 player
Audio equipment
 
Attention :
 
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power consumption of the module itself

Product Name:Universal 3V~12V 6bit Green LED Board Module for Breadboard 3d printer UNO MEGA2560 DUE FPGA CPLD PIC AVR STM32 ARM MSP430 MCU
Packing list:
 
1 pcs 6 bit Green LED's Board(Does not include ARDUIUO UNO R3);
Description:
Can be inserted directly into Arduiuo uno mega2560 Breadboard,Ideal for linking up to your Arduiuo UNO Pro Mini Nano Mega2560 DUE etc,or others MCU ( AVR STM32 ARM7 ARM9 ARM10 ARM11 PIC C8051 C51 STC MSP430 FPGA/CPLD etc.) 
 
 
1 6 bit Green Common Cathode LEDs.
 
 
2 7 PIN OUT  2.54mm
 
3 1K ohm Limiting resistor
 
4 Power Supply Voltage: 3.3-12V;
 
 
5 Size: 17.78MM x 11.43MM.
PCB:
Circuit schematics : 
Connection with Arduiuo(Only 6 bit LED's Board ,Does not include ARDUIUO UNO R3) :
Circuit schematics :
Arduiuo uno/mega2560 Code
//******************************************************//
/*
Arduiuo_6led
 
This example code is in the public domain.
*/
 
// give it a name:
int D1 = 13;
int D2 = 12;
int D3 = 11;
int D4 = 10;
int D5 = 9;
int D6 = 8;
 
// the setup routine runs once when you press reset:
void setup() {
// initialize the digital pin as an output.
pinMode(D1, OUTPUT);
pinMode(D2, OUTPUT);
pinMode(D3, OUTPUT);
pinMode(D4, OUTPUT);
pinMode(D5, OUTPUT);
pinMode(D6, OUTPUT);
}
 
// the loop routine runs over and over again forever:
void loop() {
 
digitalWrite(D1, HIGH);   // turn the LED on (HIGH is the voltage level)
delay(200);               // wait for a 200 Millisecond
digitalWrite(D1, LOW);    // turn the LED off by making the voltage LOW
 
digitalWrite(D2, HIGH);   // turn the LED on (HIGH is the voltage level)
delay(200);               // wait for a Millisecond
digitalWrite(D2, LOW);    // turn the LED off by making the voltage LOW
 
digitalWrite(D3, HIGH);   // turn the LED on (HIGH is the voltage level)
delay(200);               // wait for a Millisecond
digitalWrite(D3, LOW);    // turn the LED off by making the voltage LOW
 
digitalWrite(D4, HIGH);   // turn the LED on (HIGH is the voltage level)
delay(200);               // wait for a Millisecond
digitalWrite(D4, LOW);    // turn the LED off by making the voltage LOW
 
digitalWrite(D5, HIGH);   // turn the LED on (HIGH is the voltage level)
delay(200);               // wait for a Millisecond
digitalWrite(D5, LOW);    // turn the LED off by making the voltage LOW
 
digitalWrite(D6, HIGH);   // turn the LED on (HIGH is the voltage level)
delay(200);               // wait for a Millisecond
digitalWrite(D6, LOW);    // turn the LED off by making the voltage LOW
 
}
//******************************************************//

Description
NOTE 1 : You can go to our google drive to watch the video tutorials and download the documents:
Google Drive: https://drive.google.com/drive/folders/0B6uNNXJ2z4CxWjcybmpFOUprRWc?usp=sharing
This is a rich sensor module multifunctional kit compatible for Arduino.
The kit include an OPEN-SMART board and 9 sensor module, 3 display module and other accessories.
You can use the kit to do many projects such as Speak Clock / Speak Temperature / Clock display / Infrared Remote Control / Touch Control MP3 / MP3 Player / Ultrasonic Distance Measurement.
OPEN-SMART Board is an ATMEGA328P development board with rich peripherals.
Peripherals on OPEN-SMART Board include 4 digit display, DS1307 clock, LM75 temperature sensor, infrared receiver, serial MP3 player, rotation angle sensor, 4-channel touch sensor. Hardware resources are very rich, do not need any DuPont wires, and the usage is very simple. It is very suitable for learners.
The kit contains TF card, speaker, CR1220 battery, infrared remote control, and these are the necessary accessories for MP3,DS1307, infrared receiver.
And it contains ultrasonic sensor / water sensor / PIR motion sensor / light sensor / vibration motor / 8 – led bar / I2C 1602 display, etc.
4 digit display: 4 digit tube (0.36 inches) which can display the clock point, it needs D10/D11 pins to control and display the integer, clock, stopwatch, score and so on.
DS1307 clock: based on DS1307 high-precision real-time clock module, I2C interface, the address is 0x68.
LM75 temperature sensor: I2C interface temperature sensor, not only can measure the temperature, it can also set the temperature protection temperature, the address is 0x48.
Infrared receiver: use D2 pin,It can receive the modulated infrared signal of 38KHz that is sent by the IR transmitter module and demodulate it into logic level, and it can complete the infrared remote control with the codec program.
Serial MP3: MP3 music player module is based on high-quality MP3 music chip, use D7 / D8 pins to be software serial port, you can send commands to switch songs, change the volume and play mode and other operations.
Rotation angle sensor: 10K ohm adjustable potentiometer knob angle sensor, use A0 pin, can be used for MP3 volume adjustment, 4-digit display brightness adjustment.
4-CH touch sensor: capacitive touch switch, only when you touch the corresponding position with your fingers, the module corresponding pin (D3 / D4 / D5 / D6) will output high level, otherwise it outputs low.
NTC Temperature Sensor: can measure the temperature directly in the water.
Vibration Motor: a mini vibration motor suitable as a non-audible indicator.
I2C 1602 LCD: a high-quality 2 line 16 character LCD module with I2C interface and it is a basic character LCD screen for lots of applications.
Features:
- Use the bootloader for Arduino.
- The program, expansion shields, IDE is compatible for Arduino.
- Use through hole mount type B USB connector, consistent for the Board, ruggedness and long service life.
- You can burn the program with the type A male to type B male cable.
- Onboard 500mA resettable fuse to protect power supply from the USB port and the DC jack at the same time.
- USB interface driver chip: CH340G, compatible with win7, win8, linux, MAC OS.
- Microcontroller: Atmel ATmega328P
- Working voltage: 5V
- IO logic voltage: 5V
- Working current: 500mA (Max)
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Flash Memory: 32 KB of which 2 KB used by bootloader
- SRAM: 2KB
- EEPROM: 1KB
- Clock Speed: 16 MHz
- Onboard DIP switch, you can disconnect the connection between the peripheral module on the board and the Atmega328P.
- Onboard Shield interface, can plug the compatible expansion shield.
Photos
Part List (Schematics and program can be sent, Please contact us)
1 x Board
1 x IO Shield
1 x USB cable (50cm)
1 x 40pin female to female cable
1 x Voltage sensor
1 x Ultrasonic sensor
1 x Touch sensor
1 x Water sensor
1 x PIR motion sensor
1 x Rocker switch
1 x NTC sensor
1 x Light sensor
1 x Slide Potentiometer
1 x Vibration motor
1 x Passive buzzer
1 x Speaker
1 x 8 LED bar
1 x Eagle eyes LED
1 x I2C 1602 LCD
1 x 4-Digit display
1 x TF card (256MB)
1 x CR1220 button battery (40mAh)
1 x Infrared Remote Control (with one CR2032 battery)
1 x Micro SD card adapter
1 x Infrared emitter
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
This is multifunctional module kit compatible for Arduino.
Each module has one function, such as touch-sensing, measuring temperature, playing MP3 songs and so on.
According to the design concept of the electronic building blocks, the module has a standard interface, standard mounting holes.
You can quickly and successfully complete the development projects with R3 board, IO Expansion Shield, bread board wires for Arduino.
It can help the designer greatly speed up the progress of the invention or the scheme design.
Photos
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 x IO Expansion Shield
1 x Serial MP3 Player module
1 x 4-Digit Display module
1 x RTC module without CR1220 battery
2 x Touch Sensor module
1 x Touch Sensor(T) module
1 x Light Sensor module
2 x Water Sensor module
2 x Rotary Angle Sensor module( White Black )
1 x DS18B20 Temperature Sensor module
1 x Voltage Sensor module
2 x LED module
1 x Buzzer module
1 x MicroSD Card Adapter module
1 x PS/2 Adapter module
1 x 40P Female-to-Female Bread Board Wires (20cm)
1 x Box
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
NOTE: 
You should use two 3.7V AA lithium battery(14500) to supply power for the car.
The kit does not include any 3.7v battery.
Note2: 
You should know the package does not include any tutorial.
We can send the doc or tutorial download link to you by the station message system.
The kit is IR remote control smart car kit that is designed for ATmega328P development Board for Arduino.
Every step has a clear graphic explanation, so the installation is very simple. It contains an PCB chassis that can be easily installed with OPEN-SMART Board or other compatible motherboards. 
You can follow the installation tutorial and video to assemble the car, and each step has a clear graphic explanation, the installation is very simple.
Gear motors and battery holder are all XH-2.54 connectors, so you can plug them directly onto the corresponding white socket on the chassis.
After installation, please follow the operations in the tutorial video, so you can directly use the IR remote to control the car.
The kit can help you learn ATmega328P programming and learn how to make interesting projects, such as ultrasonic distance measurement and display, ultrasonic obstacle avoidance, bluetooth-compatible remote control smart car.
Before enjoying the car, you should get the battery power for the Smart car kit.
NOTE: The car will be shipped disassembled.
Features:
- Rubber tires: beautiful and wearable
- Using the TT gear motors, small, large torque, long service life
- Gear motor has been soldered wires, easy to use
- The car chassis has been soldered regulator circuit and motor drive module, can be directly connected to motors.
- Car chassis can install OPEN-SMART Board and compatible motherboard
- You can install HC-SR04 ultrasonic sensor.
- You can use the included Infrared Receiver module, and instead you can use other wireless modules such as Bluetooth-compatible, 433MHz remote kit, NRF24L01 transceiver module.
- Battery socket: you should use 2x 3.7V lithium batteries to supply the power for the whole car.
- It is suitable for DIY Smart car project.  
Photos

 
Part List (Schematics and program can be sent via e-mail,Please contact us)
 
1 x PCB Car Chassis
1 x OPEN-SMART Board
1 x 50cm USB Cable 
1 x IO Expansion Shield
1 x Wide-angle IR receiver module
1 x Buzzer module
4 x Gear Motor with Connection Wires(15cm)
4 x Motor Fixing
4 x Wheels
1 x 14500 Battery Holder
1 x Cross screwdriver 3*75mm
1 x 40P Female to Female Header Dupont Wire(20cm)
1 x 2P XH2.54mm cable
1 x White Nylon Rivet (R2672)
12 x Black Nylon Rivet (R2064)
3 x Copper Pillars (M3x6 6mm)
3 x Steel Screws (M3x5)
3 x Steel Hex nuts (M3 x 2.5)
6 x Steel Screws (M2x6)
2 x Copper Pillars(M2*25)
1 x IR remote(built-in one CR2032 coin battery)
1 x Packing List
 
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Features
This is a rich multifunctional kit compatible for Arduino.
The kit include an OPEN-SMART board and 9 sensor module, 4 display module and other accessories.
You can use the kit to do many projects such as Speak Clock / Speak Temperature / Clock display / Infrared Remote Control / Touch Control MP3 / MP3 Player / Ultrasonic Distance Measurement.
Easy to plug OPEN-SMART products with XH socket to the Easy IO shield and do not need to pay attention to the connection. So it is great for Training institutions and visual programming education
OPEN-SMART Board is an ATMEGA328P development board Compatible for Arduino.
The kit contains TF card, speaker, CR1220 battery, infrared remote control, and these are the necessary accessories for MP3,DS1307, infrared receiver.
And it contains ultrasonic sensor / water sensor / light sensor / vibration motor / I2C 1602 display, etc.
4 digit display: 4 digit tube (0.36 inches) which can display the clock point, it needs 2 pins to control and display the integer, clock, stopwatch, score and so on.
DS1307 clock: based on DS1307 high-precision real-time clock module, I2C interface, the address is 0x68.
Infrared receiver: It can receive the modulated infrared signal of 38KHz that is sent by the IR transmitter module and demodulate it into logic level, and it can complete the infrared remote control with the codec program.
Serial MP3: MP3 music player module is based on high-quality MP3 music chip, use D7 / D8 pins to be software serial port, you can send commands to switch songs, change the volume and play mode and other operations.
Rotation angle sensor: 10K ohm adjustable potentiometer knob angle sensor, use A0 pin, can be used for MP3 volume adjustment, 4-digit display brightness adjustment.
4-CH touch sensor: capacitive touch switch, only when you touch the corresponding position with your fingers, the module corresponding pin will output high level, otherwise it outputs low.
NTC Temperature Sensor: can measure the temperature directly in the water.
Vibration Motor: a mini vibration motor suitable as a non-audible indicator.
I2C 1602 LCD: a high-quality 2 line 16 character LCD module with I2C interface and it is a basic character LCD screen for lots of applications.
Features:
- Use the bootloader compatible for R3 Board.
- The program, expansion shields, IDE is compatible for Arduino.
- Peripheral modules are rich in type, rich library, simple sketch codes, easy functions to use.
- Use through hole mount type B USB connector, consistent for R3 Board, ruggedness and long service life.
- You can burn the program with the type A male to type B male cable.
- Onboard 500mA resettable fuse to protect power supply from the USB port and the DC jack at the same time.
- USB interface driver chip: CH340, compatible with win7, win8, win10, linux, MAC OS.
- Microcontroller: ATmega328P
- Working voltage: 5V
- IO logic voltage: 5V
- Working current: 500mA (Max)
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Flash Memory: 32 KB of which 2 KB used by bootloader
- SRAM: 2KB
- EEPROM: 1KB
- Clock Speed: 16 MHz.
Photos
 
Part List (Schematics and program can be sent , Please contact us)
1 x Board
1 x Easy IO Shield
1 x USB cable (50cm)
1 x 2pin XH2.54MM cable (12cm)
6 x 3pin XH2.54MM cable (20cm)
6 x 4pin XH2.54MM cable (20cm)
2 x 6pin XH2.54MM cable (20cm)
1 x Ultrasonic sensor
1 x Slide Potentiometer
1 x 4-CH Touch Sensor
1 x Button
1 x Water sensor
1 x Rocker switch
1 x NTC sensor(100cm)  Adapter module
1 x Light sensor
1 x Rotary angle sensor
1 x Vibration motor
1 x Serial MP3 Player
1 x Buzzer
1 x Passive buzzer
1 x Speaker
1 x Eagle eyes LED
1 x I2C 1602 LCD
1 x 4-Digit display
1 x RGB LED
1 x TF card (256MB)
1 x Blue DS1307 RTC ( built-in one CR1220 button battery 40mAh )
1 x Infrared Remote Control (built-in one CR2032 battery 80mAh)
1 x Infrared receiver
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
Use for android phone and for iOS phone to control smart car easily.
NOTE1:
The kit does not include any battery.
You should use three 3.7V lithium battery(18650) to supply power for the car and the Joystick remote. Such as this picture shows:
NOTE2:
You should know the package does not include any tutorial.
We can send the doc or tutorial download link to you by the message system.
NOTE3:
The car will be shipped disassembled.
The kit is RF 315MHz joystick remote control Omnidirectional smart car kit that is designed for Arduino development board.
It contains acompatible PCB chassis that can be easily installed for Arduino UNO R3 / OPEN-SMART C Board or other compatible motherboards.
Gear motors and battery holder are all XH-2.54 connectors, so you can plug them directly onto the corresponding white socket on the chassis.
This kit includes an OPEN-SMART C board which uses type-C USB interface.
Easy to plug OPEN-SMART products with XH socket to the Easy IO Shield Pro and do not need to pay attention to the connection. So it is great for training institutions and visual programming education.
This kit includes a 4-Channel 1.2A L293DD quad motor driver module, so you can control the 4 DC motors independently.
This kit includes special wheel that can help the car to make an omnidirectional move.
The kit can help you learn for Arduino programming and learn how to make interesting projects, such as ultrasonic distance measurement,ultrasonic obstacle avoidance, joystick remote control smart car.
Features:
- Easy to install.
- Rubber tires: beautiful and wearable
- Using the TT gear motors, small, large torque, long service life
- Gear motor has been soldered wires, easy to use
- The car chassis has been soldered regulator circuit that can help to supply power for motor driver
and for Arduino board.
- Wireless joystick frequency: 315MHz.
- Car chassis can install OPEN-SMART C Board and compatible motherboard
- You can install HC-SR04 ultrasonic sensor.
- You can use the included wireless joystick remote module, and instead you can use other wireless modules such as Bluetooth, infrared, NRF24L01 transceiver module.
- It is suitable for DIY Smart Car project.
Photos
Part List :
1 x PCB Car Chassis
1 x OPEN-SMART C Board
1 x Easy IO Shield Pro
1 x 100cm Type-C Cable
4 x Wheels
4 x Gear Motor with Wires(15cm)
4 x Motor Fixing
1 x Quad Motor Driver
1 x Ultrasonic Sensor module
1 x Ultrasonic Sensor Acrylic stand
1 x RF 315MHz Receiver module
1 x RF 315MHz Joystick Control
1 x 18650 Battery Holder
4 x White Nylon Rivet (R4070)
2 x Copper Pillars (M3x6 6mm)
2 x Steel Screws (M3x5)
2 x Steel Hex nuts (M3 x 2.5)
2 x 2pin XH2.54MM cable (12cm)
1 x 3pin XH2.54MM cable (20cm)
5 x 4pin XH2.54MM cable (20cm)
1 x Cross screwdriver 5*75mm
1 x Packing List
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
NOTE1:
You should use two 3.7V AA lithium battery(14500) to supply power for the car.
The kit does not include any battery.
Note2: 
You should know the package does not include any tutorial.
We can send the doc or tutorial download link to you by the station message system.
The kit is wireless joystick remote control smart car kit that is designed for ATmega328P development Board compatible for Arduino.
Every step has a clear graphic explanation, so the installation is very simple.
It contains an PCB chassis that can be easily installed with OPEN-SMART Board or other compatible motherboards. 
You can follow the installation tutorial and video to assemble the car, and each step has a clear graphic explanation, the installation is very simple.
Gear motors and battery holder are all XH-2.54 connectors, so you can plug them directly onto the corresponding white socket on the chassis.
After installation, please follow the operations in the tutorial video, so you can directly use the wireless joystick remote to control the car.
The kit can help you learn ATmega328P programming and learn how to make interesting projects, such as ultrasonic distance measurement and display, ultrasonic obstacle avoidance, bluetooth-compatible remote control smart car.
Before enjoying the car, you should get the battery power for the Wireless Joystick Remote and the Smart car.
NOTE3: The car will be shipped disassembled and the batteries is not included, please know.
NOTE4: For the power for the remote control, you can use 3.7V lithium battery with XH2.54 connector. You can refer to the red and black line order from the follow reference photo:
Features:
- Rubber tires: beautiful and wearable
- Using the TT gear motors, small, large torque, long service life
- Gear motor has been soldered wires, easy to use
- The car chassis has been soldered regulator circuit and motor drive module, can be directly connected to motors.
- Car chassis can install OPEN-SMART Board and compatible motherboard
- You can install HC-SR04 ultrasonic sensor.
- You can use the included wireless joystick remote module, and instead you can use other wireless modules such as Bluetooth-compatible module, infrared, NRF24L01 transceiver module.
- It is suitable for DIY Smart car project.  
Photos
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 x PCB Car Chassis
1 x OPEN-SMART Board
1 x 50cm USB Cable
1 x IO Expansion Shield
1 x Ultrasonic Sensor module
1 x Ultrasonic Sensor Acrylic stand
1 x Joystick Remote control
1 x RF433 Receiver module
1 x 4-Digit Display module
4 x Gear Motor with Connection Wires(15cm)
4 x Motor Fixing
4 x Wheels
1 x 14500 Battery Holder
1 x Cross screwdriver
1 x 40P Female to Female Header Dupont Wire(20cm)
1 x 2P XH2.54mm cable
1 x White Nylon Rivet (R2672)
12 x Black Nylon Rivet (R2064)
3 x Copper Pillars (M3x6 6mm)
3 x Steel Screws (M3x5)
3 x Steel Hex nuts (M3 x 2.5)
1 x Packing List
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
Use for android phone and for iOS phone to control smart car easily. 
NOTE:
The kit does not include any battery.
You should use two 3.7V AA lithium battery(14500) to supply power for the car.
NOTE2:
You should know the package does not include any tutorial.
We can send the doc or tutorial download link to you by the station message system.
The kit is Bluetooth-compatible remote control smart car kit that is designed compatible for Arduino.
Every step has a clear graphic explanation, so the installation is very simple.
It contains an compatible PCB chassis that can be easily installed for Arduino.
And it can installed other compatible motherboards. 
You can follow the installation tutorial and video to assemble the car, and each step has a clear graphic explanation, the installation is very simple.
Gear motors and battery holder are all XH-2.54 connectors, so you can plug them directly onto the corresponding white socket on the chassis.
After installation, please follow the operations in the tutorial video, so you can directly use for android phone to control the car. 
In addition to use the touch buttons on the APP page, you can also use the gyroscope control built in the phone.
The kit can help you learn for programming and learn how to make interesting projects, such as ultrasonic distance measurement and display, ultrasonic obstacle avoidance, remote control smart car.
NOTE3: The car will be shipped disassembled.
Features:
- Rubber tires: beautiful and wearable
- Using the TT gear motors, small, large torque, long service life
- Gear motor has been soldered wires, easy to use
- The car chassis has been soldered regulator circuit and motor drive module, can be directly connected to motors.
- Car chassis can install for OPEN-SMART Board and compatible motherboard, or for Digispark Motherboard.
- You can install HC-SR04 ultrasonic sensor.
- You can use the included Bluetooth-compatible wireless transceiver module, and instead you can use other wireless modules such as infrared, NRF24L01 transceiver module, 433M remote control kit.
- It is suitable for DIY Smart car project.
Photos
 
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 x PCB Car Chassis
1 x OPEN-SMART Board
1 x 50cm USB Cable
1 x IO Expansion Shield
1 x Ultrasonic Sensor module
1 x Ultrasonic Sensor Acrylic stand
1 x Serial Bluetooth-compatible module
1 x 4-Digit Display module
4 x Gear Motor with Connection Wires(15cm)
4 x Motor Fixing
4 x Wheels
1 x 14500 Battery Holder
1 x Cross screwdriver 3*75mm
1 x 40P Female to Female Header Dupont Wire(20cm)
1 x White Nylon Rivet (R2672)
12 x Black Nylon Rivet (R2064)
3 x Copper Pillars (M3x6 6mm)
3 x Steel Screws (M3x5)
3 x Steel Hex nuts (M3 x 2.5)
1 x Packing List
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
NOTE: You can go to our google drive to watch the video and download the documents.
NOTE: This kit does not include the MCU development board. You can Buy the OPEN-SMART Board here :
For Red Color OPEN-SMART Board:   //////////////////////////////////  For the Black Color OPEN-SMART Board:
------/------
------------------------------------------------------------------------------------------------------------------------------------------------------------------------
This is a rich multifunctional kit for Arduino with 9 sensor modules, 4 display module and other accessories. You can use the kit to do many projects such as Speak Clock / Speak Temperature / Clock display / Infrared Remote Control / Touch Control MP3 / MP3 Player / Ultrasonic Distance Measurement.
Easy to plug OPEN-SMART products with XH socket to the Easy IO shield and do not need to pay attention to the connection. So it is great for Training institutions and visual programming education
Compatible with Arduino, OPEN-SMART ONE R3 which is an ATMEGA328 development board.
The kit contains TF card, speaker, CR1220 battery, infrared remote control, and these are the necessary accessories for MP3,DS1307, infrared receiver.
And it contains ultrasonic sensor / water sensor / light sensor / vibration motor / I2C 1602 display, etc.
4 digit display: 4 digit tube (0.36 inches) which can display the clock point, it needs 2 pins to control and display the integer, clock, stopwatch, score and so on.
DS1307 clock: based on DS1307 high-precision real-time clock module, I2C interface, the address is 0x68.
Infrared receiver: It can receive the modulated infrared signal of 38KHz that is sent by the IR transmitter module and demodulate it into logic level, and it can complete the infrared remote control with the codec program.
Serial MP3: MP3 music player module is based on high-quality MP3 music chip, use D7 / D8 pins to be software serial port, you can send commands to switch songs, change the volume and play mode and other operations.
Rotation angle sensor: 10K ohm adjustable potentiometer knob angle sensor, use A0 pin, can be used for MP3 volume adjustment, 4-digit display brightness adjustment.
4-CH touch sensor: capacitive touch switch, only when you touch the corresponding position with your fingers, the module corresponding pin will output high level, otherwise it outputs low.
NTC Temperature Sensor: can measure the temperature directly in the water.
Vibration Motor: a mini vibration motor suitable as a non-audible indicator.
I2C 1602 LCD: a high-quality 2 line 16 character LCD module with I2C interface and it is a basic character LCD screen for lots of applications.
Features:
- Rich types of peripheral modules, rich program libraries, simple code, and simple functions.
- Suitable for MCU development board whose working voltage is 5V.
- The provided library is for Arduino or compatible development boards.
- Modules for analog input: 5.
- Modules for digital input and output: 11.
- Modules for I2C interface: 2.
- Modules for UART interface : 1.
Photos
Part List
1 x Easy IO Shield
1 x 2pin XH2.54MM cable (12cm)
6 x 3pin XH2.54MM cable (20cm)
6 x 4pin XH2.54MM cable (20cm)
2 x 6pin XH2.54MM cable (20cm)
1 x Ultrasonic sensor
1 x Slide Potentiometer
1 x 4-CH Touch Sensor
1 x Button
1 x Water sensor
1 x Rocker switch
1 x NTC sensor(100cm) Adapter module
1 x Light sensor
1 x Rotary angle sensor
1 x Vibration motor
1 x Serial MP3 Player
1 x Buzzer
1 x Passive buzzer
1 x Speaker
1 x Eagle eyes LED
1 x I2C 1602 LCD
1 x 4-Digit display
1 x RGB LED
1 x TF card (256MB)
1 x Blue DS1307 RTC ( built-in one CR1220 button battery 40mAh )
1 x Infrared Remote Control (built-in one CR2032 battery 80mAh)
1 x Infrared receiver
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
It can measure the pressure of non-corrosiveness gas or liquid and output linear analog voltage.   
Features:
- Working Voltage VCC: 5.0 VDC
- Output Voltage: 0.5-4.5 VDC, Vout = VCC*(1.6*Pressure 0.1)
- Working Current: <=10 mA
- Pressure Scale: 0-0.5 MPa
- The Biggest Pressure: 1.5 MPa
- Destroy Pressure: 3.0 MPa
- Working temperature range: 0-85 Celsius Degree
- Measuring Error:±1.5 % FSO
- Temperature Range Error: ±3.5 % FSO
- Response Time: <=2.0 ms
- Variable-speed pump interface: G1/4 (1/4 inch)
- Output connector: XH2.54MM-3P
- Output leads: yellow (DATA), red (VCC), black (GND)
- sLead length: 20cm
Photos
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 x Module
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
No additional modules, this kit can achieve rich projects such as character display, image reading and display, touch sketchpad, temperature measurement and display.
The kit includes a OPEN-SMART 5V / 3.3V board, and the program, expansion shields, IDE is compatible for Arduino.
The kit includes a 2.8 inch TFT touch screen expansion board using standard Shield interface and it has good compatibility.
It integrates a 2.8-inch touch screen, I2C temperature sensor, TF card holder, level conversion circuit, and the secondary development is less difficult.
With GPRS module, you can design your DIY phone.
With NFC reader module, you can create access control systems with the photos show.
- Can use it directly to display characters, graphics and BMP format images. And touch controlling is available.
- Compatibility: As the SD card is connected to SPI pins of ICSP  interface, it's also compatible for Mega2560 Board.
- USB interface driver chip: CH340;
- Microcontroller: ATmega328P or ATmega328PB;
- Library: TFTLibrary and Adafruit_GFX;
- Touch screen type: resistive touchscreen.
- Touch Pen: length is 9cm;
- Resolution: 240X320;
- Display size: 2.8 inch;
- Operating voltage: 5V;
- Logic level: 5V / 3.3V;
- On-board 3.3V / 300mA regulator circuit;
- Operating current: the maximum is 150mA
- Use the A0 ~ A3 pins, D4 ~ D13 pins. And  I2C interface, D0 / D1 / D2 / D3 is available, please refer to the product schematics for the details.
- Onboard Micro SD slot, support Micro SD / TF Card;
- Onboard LM75 temperature sensor: default I2C address is 0X48, scale is -20 ~ 80'C
- Great for DIY
2.8inch TFT LCD Dimensions  and View area:
Photos
Part List(Schematics and program can be sent, Please contact us)
1 x Shield
1 x Board
1 x USB cable (50cm)
1 x Micro SD card (256MB)
1 x Touch pen
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description   
When you give high level for the pin of the module, the electromagnet can suck magnetically conductive object. Otherwise it will release the object.
An electromagnet is a type of magnet in which the magnetic field is produced by electric current. An electric current flowing in a wire creates a magnetic field around the wire, due to Ampere's law.
To concentrate the magnetic field, in an electromagnet the wire is wound into a coil with many turns of wire lying side by side. The magnetic field of all the turns of wire passes through the center of the coil, creating a strong magnetic field there.
It is easy to use, to learn electromagnet principle.
Note: If something needs to be attract by an electromagnet, the thing is a material that can be magnetized, please know.
The electromagnet must meet the following conditions in use to achieve maximum attraction:
1. Suction object must be a material with good magnetic permeability.
2. The surface of the sucked object must be flat and clean。
3. The contact area between the sucked object and the electromagnet must be greater than or equal to the maximum outer diameter of the electromagnet.
4. The thickness of the suction object must be greater than 8mm, otherwise the suction force will be reduced.
5.  Do not place anything between the sucked object and the electromagnet.
6. Use the correct power and voltage.
Features:
- Working Voltage: 3.2 - 5.3VDC
- Working Current: 200mA(MAX)
- Drive current from SIG pin: 4.3mA (@VCC = 5V)
- Load Weight: 1KG / 10N (MAX)
- Active level: High level(3.0 - 5.5V)
Photos
 
Part List (Schematics and program can be sent,Please contact us)
 
1 x Board
 
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
Use for android phone and for iOS phone to control smart car easily. 
NOTE: 
You should use two 3.7V AA lithium battery(14500) to supply power for the car.
The kit does not include any battery.
The kit is remote control smart car kit that is designed compatible for Arduino.
It contains an compatible PCB chassis, the motor driver circuit, a Bluetooth-compatible transceiver module, a ultrasonic ranging module, and you can easily install for R3 Board or other compatible motherboard.
When you get the parts, you can follow the electronic version of the installation tutorial to assemble the car. Every step has a clear graphic explanation, so the installation is very simple.
The kit can help you learn for programming and learn how to make interesting projects, such as ultrasonic distance measurement and display, Bluetooth-compatible remote control smart car.
You only need to purchase two pieces of 3.7V 14500 lithium battery to complete the smart car project.
NOTE: The car will be shipped disassembled.
Features:
- Rubber tires: beautiful and wearable
- Using the N20 geared motors, small, large torque, long service life
- N20 motor has been soldered wires, easy to use
- The car chassis has been soldered regulator circuit and motor drive module, can be directly connected to motors.
- Car chassis can install for R3 Board and compatible motherboard, or for Digispark Motherboard
- You can install HC-SR04 ultrasonic sensor.
- You can use the included Bluetooth-compatible wireless transceiver module, and instead you can use other wireless modules such as infrared, NRF24L01 transceiver module, 433M remote control kit.
- It is suitable for DIY Smart car project.
Photos
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 x Smart Car Kit
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Features
No additional modules, this kit can achieve rich projects such as character display, image reading and display, touch sketchpad.
The kit includes a 2.0 inch TFT touch screen breakout board, and the secondary development is easy.
The kit includes an Easy-plug ONE R3 Air development board. And the program, expansion Shields, IDE is compatible for Arduino.
There's a switch to choose the system supply voltage, 3.3V or 5V, which is very useful if you want to set the system to 3.3V to save power.
For example, you want to connect directly 3.3V LCD / ESP8266 wifi-compatible / BME280 barometric sensor module for the Board without level conversion module, you can set the Air Board to be 3.3V level.
With GPRS module, you can design your DIY phone.
With NFC reader module, you can create access control systems with the photos show.
With voltage and current sensor, you can make oscilloscope.
2.0 inch TFT LCD :
- Can use it directly to display characters, graphics and BMP format images. And touch controlling is available;
- Touch screen type: resistive touchscreen.
- Touch Pen: length is 9cm;
- Resolution: 176 * 220
- Display size: 2.0 inch;
- Operating voltage: 3.3V;
- Logic level: 3.3V;
Air Board:
- Operating current: the maximum is 500mA
- I2C female header: can connect to DS1307 RTC / LM75A temperature sensor / I2C 1602 LCD
- GPIO(D2 and D3) female header: can connect to Serial MP3 Player / Serial Bluetooth-compatible module
- SPI female header: can connect to MicroSD card Adapter module
- TFT LCD female header: can connect to OPEN-SMART TFT LCD breakout module(2.0”, 2.2”, 2.8”, 3.5”)
- Very suitable for digital photo frame, oscilloscope, function generator, detection system monitor.
Photos
Part List (Schematics and program can be sent , Please contact us)
1 x 2.0inch TFT
1 x Board
1 x USB cable (50cm)
1 x Micro SD card (128MB)
1 x Touch pen
1 x Micro SD card Adapter module
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

NOTE: You can go to our google drive to watch the video and download the documents.
This is a rich multifunctional kit compatible for Arduino.
The kit include a Rich OPEN-SMART board and 9 sensor module, 3 display module and other accessories.
You can use the kit to do many projects such as Speak Clock / Speak Temperature / Clock display / Infrared Remote Control / Touch Control MP3 / MP3 Player / Ultrasonic Distance Measurement.
Features:
- Use the compatible bootloader.
- The program, expansion shields, IDE is compatible for Arduino.
- Peripheral modules are rich in type, rich library, simple sketch codes, easy functions to use.
- Use through hole mount type B USB connector, consistent for Board, ruggedness and long service life.
- You can burn the program with the type A male to type B male cable.
- Onboard 500mA resettable fuse to protect power supply from the USB port and the DC jack at the same time.
- USB interface driver chip: CH340G, compatible with win7, win8, linux, MAC OS.
- Microcontroller: Atmel ATmega328P
- Working voltage: 5V
- IO logic voltage: 5V
- Working current: 500mA (Max)
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Flash Memory: 32 KB of which 2 KB used by bootloader
- SRAM: 2KB
- EEPROM: 1KB
- Clock Speed: 16 MHz.
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

You can also buy Programmer Module Test Tool PCB Test Fixture 1 * 10P here (Link) :
NOTE: If you have other Pin count requirement, please contact with us before ordering.
Description
This is a test fixture dedicated to module testing and code burning. It is suitable for modules and boards without soldering pin headers, and can be used to upload code for sketch to Pro Mini / OPEN-SMART Mini ATmega8 without soldering pin headers.
feature:
- Number of Pins: 1X6P
- Pin pitch: 2.54mm
- Probe head type: P75-E3 (cone), gold-plated, durable
- Probe head applicable pad: through pad, surface pad
- Probe receptacle type: R75-3W
- Probe receptacle tail specifications: 0.64X0.64MM, apply to DuPont cable
- Wire slot specifications: width 6mm, height 6mm (can pass through 12 DuPont line)
- Operating current: Each pin 1A (max)
- Operating voltage: 30V (max)
Photos
 
Part List (Schematics and program can be sent, Please contact us)
 
1 x Test Fixture
 
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Features
No additional modules, this kit can achieve rich projects such as character display, image reading and display, touch sketchpad.
The kit includes a 3.5 inch TFT touch screen breakout board, and the secondary development is easy.
The kit includes an Easy-plug development board. And the program, expansion Shields, IDE is compatible for Arduino.
There's a switch to choose the system supply voltage, 3.3V or 5V, which is very useful if you want to set the system to 3.3V to save power.
For example, you want to connect directly for 3.3V LCD / ESP8266 wifi-compatibke / BME280 barometric sensor module for the Board without level conversion module, you can set the board to be 3.3V level.
With GPRS module, you can design your DIY phone.
With NFC reader module, you can create access control systems with the photos show.
With voltage and current sensor, you can make oscilloscope.
3.5 inch TFT LCD:
- Can use it directly to display characters, graphics and BMP format images. And touch controlling is available;
- Touch screen type: resistive touchscreen.
- Touch Pen: length is 9cm;
- Resolution: 400 x 240, 16-bit (262,000) color
- Display size: 3.5 inch;
- Operating voltage: 3.3V;
- Logic level: 3.3V;
The Air Board:
- Operating current: the maximum is 500mA
- I2C female header: can connect to DS1307 RTC / LM75A temperature sensor / I2C 1602 LCD
- GPIO(D2 and D3) female header: can connect to Serial MP3 Player / Serial Bluetooth-compatible module
- SPI female header: can connect to MicroSD card Adapter module
- TFT LCD female header: can connect to OPEN-SMART TFT LCD breakout module(2.0”, 2.2”, 2.8”, 3.5”)
- Very suitable for digital photo frame, oscilloscope, function generator, detection system monitor.
3.5inch TFT LCD Dimensions  and View area:
Photos
Part List(Schematics and program can be sent , Please contact us)
1 x 3.5 inch TFT
1 x Board
1 x USB cable (50cm)
1 x Micro SD card (128MB)
1 x Touch pen
1 x Micro SD Card Adapter module
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Features
This is a 2.8 inch TFT LCD expansion board. This display has a controller built into it with RAM buffer, so that almost all work is done by the TFT.
It leads out the pins of the TFT and breakout pins pitch is 2.54mm, so the secondary development is easy.
With GPRS module, you can design your DIY phone.
With NFC reader module, you can create access control systems with the photos show.
With voltage and current sensor, you can make oscilloscope.
- Can use it directly to display characters, graphics and BMP format images with the help of Micro SD card adapter module.
- Compatibility: Because the logic level is 3.3V, it is compatible for board 3.3V, you generally need to add a level conversion circuit if you use a 5V Board for Arduino.
- Touch screen type: resistive touchscreen.
- Touch Pen: length is 9cm;
- Resolution: 320 * 240, 16-bit (262,000) color
- Display size: 2.8 inch;
- Operating voltage: 3.3V;
- Logic level: 3.3V;
- Operating current: the maximum is 60mA
- Bus interface: 8080-parallel interface (8 bit)
- IO Port Package: PAD is available, and the pin pitch is 2.54mm.
- LED pin can connect to external backlight control circuit to control the brightness of backlight. You can connect it to GND to turn on the backlight all day.
- Very suitable for digital photo frame, oscilloscope, function generator, detection system monitor
2.8inch TFT LCD Dimensions  and View area:
Photos
Dimensions:
Part List(Schematics and program can be sent , Please contact us)
1 x Module
1 x Touch pen
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
This kit includes PCB experimental board, lead-free solder wire, male pin header, female pin header, resistor.
Features:
- Tin wire: diameter 0.8mm, lead-free solder wire, soldering easy
- Experimental board: single-sided tin plated
- Wire jumper pack of different lengths, can be used to connect two pads
- Using these resistors and LED, you can make some basic projects.
Photos
 
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 * Reel solder wire
3 * PCB experiment board (5 * 7cm)
3 * PCB experimental Board (7 * 9cm)
25 * Resistor, 220ohm-1% -1 / 4W
25 * Resistor, 1K-1% -1 / 4W
25 * Resistor, 4.7K-1% -1 / 4W
25 * Resistor, 10K-1% -1 / 4W
5 * Aluminum electrolytic capacitor 47UF
5 * Monolithic capacitor 100nF
5 * 3mm red LED
5 * 3mm green LED
5 * 3mm blue LED
1 * Jumper wire (5cm ~ 10cm)
3 * 40P pin header
3 * 40P female pin header
1 * Box
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Features
No additional modules, this kit can achieve rich projects such as character display, image reading and display, touch sketchpad.
The kit includes a 2.8 inch TFT touch screen breakout board, and the secondary development is easy.
The kit includes an Easy-plug development board. And the program, expansion Shields, IDE is compatible for Arduino.
There's a switch to choose the system supply voltage, 3.3V or 5V, which is very useful if you want to set the system to 3.3V to save power.
For example, you want to connect directly for 3.3V LCD / ESP8266 wifi-compatible / BME280 barometric sensor module for the Board without level conversion module, you can set the Air Board to be 3.3V level.
With GPRS module, you can design your DIY phone.
With NFC reader module, you can create access control systems with the photos show.
With voltage and current sensor, you can make oscilloscope.
2.8 inch TFT LCD :
- Can use it directly to display characters, graphics and BMP format images. And touch controlling is available;
- Touch screen type: resistive touchscreen.
- Touch Pen: length is 9cm;
- Resolution: 240 * 320
- Display size: 2.8 inch;
- Operating voltage: 3.3V;
- Logic level: 3.3V;
Air Board :
- Operating current: the maximum is 500mA
- I2C female header: can connect to DS1307 RTC / LM75A temperature sensor / I2C 1602 LCD
- GPIO(D2 and D3) female header: can connect to Serial MP3 Player / Serial Bluetooth-compatible module
- SPI female header: can connect to MicroSD card Adapter module
- TFT LCD female header: can connect to OPEN-SMART TFT LCD breakout module(2.0”, 2.2”, 2.8”, 3.5”)
- Very suitable for digital photo frame, oscilloscope, function generator, detection system monitor.
Photos
Part List(Schematics and program can be sent , Please contact us)
1 x 2.8 inch TFT
1 x Board
1 x USB cable (50cm)
1 x Micro SD card (128MB)
1 x Touch pen
1 x Micro SD card Adapter module
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
This is a radio frequency ID card reader module that can read the ID card's serial number. It can help to design the intelligent access control system.
When the module sensed ID card, it will convert the card number into a 8-digit hexadecimal number, each digit of which will be converted into ASCII code.
Then it adds the starting byte and 5 other bytes, so a total of 14bytes output to the serial port. You can convert it into a decimal number that is the serial number engraved on the ID card.
Features:
- Support Card Type: Read-only ID cards (such as EM4100, EM4001, etc.);
- Working voltage: 4.5-5.5VDC;
- Working current: 40mA (max);
- Working frequency: 125KHz;
- Reading distance: 1-3cm;
- Logic Interface: UART TTL serial port;
- Communication format: 8N1;
- Baud rate: 9600 ;
- Induction coil: soldered on the board;
- Coil size: 35X40mm;
- PCB size: 53x37mm;
- Easy to use and great for DIY;
- Applications: Access control systems, Attendance system;
Photos
Part List
1 x  module
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
NOTE:The screen may have a bright pixel that will light all day on but it does not affect the application.
If you buy it, that means you know this exactly and accept it, please know.
No additional modules, this kit can achieve rich projects such as character display, image reading and display, touch sketchpad, temperature measurement and display.
The program, expansion shields, IDE is compatible for MEGA2560 R3.
The kit includes a 3.2 inch TFT touch screen expansion board using standard Shield interface and it has good compatibility. Itintegrates a 3.2-inch touch screen, I2C temperature sensor, TF card holder, level conversion circuit, and the secondary development is easy.
With GPRS module, you can design for DIY phone.
With NFC reader module, you can create access control systems with the photos show.
With voltage and current sensor, you can make oscilloscope.
- Can use it directly to display characters, graphics and BMP format images. And touch controlling is available;
- Compatibility: As the SD card is connected to SPI pins of ICSP  interface, it is compatible for Arduino.
- Library: TFTLibrary and Adafruit_GFX;
- Touch screen type: resistive touchscreen.
- Touch Pen: length is 9cm;
- Resolution: 240X320;
- Display size: 3.2 inch;
- Operating voltage: 5V;
- Logic level: 5V / 3.3V;
- On-board 3.3V / 300mA regulator circuit;
- Operating current: the maximum is 150mA
- Use the A0 ~ A3 pins, D4 ~ D13 pins. And  I2C interface, D0 / D1 / D2 / D3 is available, please refer to the product schematics for the details.
- Onboard Micro SD slot, support Micro SD / TF Card;
- Onboard LM75 temperature sensor: default I2C address is 0X48, scale is -55 ~ 125'C
- Very suitable for digital photo frame, oscilloscope, function generator, detection system monitor.
Photos
Part List(Schematics and program can be sent via e-mail,Please contact us)
1 x Shield
1 x Board
1 x USB cable (50cm)
1 x Micro SD card (256MB)
1 x Touch pen
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
Clock Shield (digital clock module) Shield contains most common resources for a basic electronic project, like buttons, sensors, buzzer and display, it's compatible for Arduino.
And it is a perfect start for beginners.
Features
1 Brand new handy and pretty cheap
2 Can be directly inserted on the compatible board
3 On-board real-time clock chip
4 For rich supporting experimental routines with other SCM systems
5 Handy and pretty cheap
Specificaton
Item

Min

Typical values

Max

Unit
Voltage

4.5

5

5.5

V
Current

—

80

—

mA
Size

74x59x30

mm
Net weight

35

g
Interface
Clock Shield interface as shown below:
Hardware resources:
Battery Holder : Battery on the card to the real-time clock chip power supply , making the board can continue to power down timer ;
Buzzer : 5V DC buzzer , do alarm clock, key tone ;
Photoresistor : intensity of ambient light sensor ;
Thermistor: detecting environmental temperature ;
K1 ~ K3: SCM can be scanned directly touch of a button ;
U5: TM1636, namely, four 8-segment common anode LED Driver IC ;
U3: DS1307, namely, real-time clock chip ;
D1 ~ D4: blue, green , red, red , 3mm plug LED.
Digital tube: 4 8 segments of positive points with a digital clock , and the decimal point is not displayed , only for identification purposes direction .
Occupied Shield pin Resources: Total occupied nine digital pins , two analog input pins, an I2C interface
D2: control blue LED1;
D3: Control the green LED2;
D4: Control the red LED3;
D5: Control the red LED4;
D7: connection TM1636 clock pin SCLK;
D8: TM1636 data connection pin DIO;
D9: control keys K1;
D10: control buttons K2;
D11: control buttons K3;
A0: poll readings from temperature sensor;
A1: poll readings from light sensor;
A4: connect the DS1307 I2C data pin SDA;
A5: connect the DS1307 I2C clock pin SCL
Photos
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 x Clock Shield 
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
This is high speed 8-Bit bidirectional voltage-Level translator module. It is commonly used to match those circuits whose logic level is inconsistent, such as 5V motherboard IO ports and peripheral modules of 3.3V.
- Level translation rate: 2Mbps (open-drain driving), 60Mbps(Push-pull driving @VCCA=3.3V)
- VCCA voltage: 1.2V-3.6V
- VCCB voltage: 1.65V-5.5V
- Voltage of VCCA should not be greater than VCCB
- Supports 3.3V-5V, 1.8V-3.3v and other common level translation
- Applicable to 5V microcontroller and 3.3V module
- Great for DIY
Photos
 
 
Part List (Schematics and program can be sent via e-mail,Please contact us)
1 x  8-Bit Bidirectional Voltage level shifter  
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Description
Use for android phone and for iOS phone to control smart car easily.
NOTE1:
The kit does not include any battery.
You should use two 3.7V lithium battery(18650) to supply power for the car. Such as this picture shows:
NOTE2:
You should know the package does not include any tutorial.
We can send the doc or tutorial download link to you by the message system.
NOTE3:
The car will be shipped disassembled.
This is a bluetooth-compatible remote control Omnidirectional smart car kit that is designed for Arduino.
It contains a compatible PCB chassis that can be easily installed for OPEN-SMART Board or other compatible motherboards.
Gear motors and battery holder are all XH-2.54connectors,so you can plug them directly onto the corresponding white socket on the chassis.
This kit includes an OPEN-SMART board which use stype-C USB interface.
Easy to plug OPEN-SMART products with XH socket to the Easy IO shield Pro and do not need to pay attention to the connection. So it is great for training institutions and visual programming education.
This kit includes a 4-Channel 1.2A L293DD quad motor driver module, so you can control the 4 DC motors independently.
This kit includes special wheel that can help the car to make an omnidirectional move.
The kit can help you learn for programming and learn how to make interesting projects, such as ultrasonic distance measurement,ultrasonic obstacle avoidance, remote control smart car.
Features:
- Easy to install.
- Rubber tires: beautiful and wearable
- Using the TT gear motors, small, large torque, long service life
- Gear motor has been soldered wires, easy to use
- The car chassis has been soldered regulator circuit that can help to supply power for motor driver and the board.
- Car chassis can install for OPEN-SMART Board and compatible motherboard
- You can install HC-SR04 ultrasonic sensor.
- You can use the included bluetooth-compatible wireless transceiver module, and instead you can use other wireless modules such as infrared, NRF24L01 transceiver module, 433M remote control kit.
- It is suitable for DIY Smart car project.
Photos
Part List :
1 x PCB Car Chassis
1 x OPEN-SMART C Board
1 x 100cm Type-C Cable
1 x Easy IO Shield Pro
1 x Ultrasonic Sensor module
1 x Ultrasonic Sensor Acrylic stand
1 x Serial Bluetooth-compatible module
1 x Quad Motor Driver
4 x Gear Motor with Wires(15cm)
4 x Motor Fixing
4 x Wheels
1 x 18650 Battery Holder
2x 2pin XH2.54MM cable (12cm)
5x 4pin XH2.54MM cable (20cm)
1 x Cross screwdriver 5*75mm
4 x White Nylon Rivet (R4070)
2 x Copper Pillars (M3x6 6mm)
2 x Steel Screws (M3x5)
2 x Steel Hex nuts (M3 x 2.5)
1 x Packing List
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)

Features
Note: This kit will be send as parts, please know
This is high quality DIY board Soldering Parts Kit for Arduino.
The development board based on ATMEGA328P.
It is great for beginners, students, training institutions.
Advanced Features:
- Included ATmega328P-PU has been burned for R3 bootloader;
- Included CH340 USB to UART module that you can upload code directly after install CH340 driver for your PC, compatible with win7, win8, linux, MAC OS;
- Included colorful Standard Shield pin headers ;
- Included 3 Programmable LEDs which connect to D13 / D8 / D7;
- Included 3 Buttons which connect to D4 / D3 / D2;
- Included 1 Buzzer which connect to D6;
- Included 28PIN-DIP socket so you can replace the ATmega328P-PU chip;
- Included 49S Crystal oscillator socket, so you can replace it easily;
- The program, expansion shields, development environment IDE is compatible.
- Microcontrollers: ATmega328P-PU
- Operating voltage: 5V
- IO interface logic voltage: 5V
- Operating Current: 500mA (max)
- Digital I / O pins: 14 (of which 6 can provide PWM output)
- Analog input pins: 6
- Clock frequency: 16MHz
- Onboard power indicator.
- Bootloader burning Interface: ICSP
Soldering in the order shown in the following table:
Then, you can plug the HC-49S 16MHz crystal oscillator onto the 3pin Round hole pin header.
And then, you can plug ATmega328P-PU onto the 28PIN-DIP socket, please pay attention to the direction and be careful
not to bend the pins.
After you have done all of the previous steps, you can use it as for R3 board because the ATmega328P-PU has been
burned for R3 bootloader.
Photos
Part List (Schematics and program can be sent , Please contact us)
4 x 1kOhm metal film resistor
2 x 10kOhm metal film resistor
1 x USB to UART module
1 x 2pin button
2 x 22pF Ceramic capacitor
3 x 100nF ceramic capacitor
1 x 3pin Round hole pin header
1 x 28PIN-DIP socket
1 x Buzzer
1 x Aluminum electrolytic capacitor 47uF
1 x 5mm Red LED
1 x 5mm Green LED
2 x 5mm Yellow LED
1 x 10pin yellow female pin header
1 x 8pin yellow female pin header
1 x 2X3P pin header
1 x 6pin blue female pin header
1 x 8pin red female pin header
1 x USB socket
3 x 4pin button
1 x ATmega328P-PU
1 x HC-49S 16MHz crystal oscillator
1 x DIY PCB
1 x USB cable(50cm)
               
Please Note That (Note: After you buy the product, the documents can be send, Please contact us)